Classic Flame 52EB497GRA Manuel utilisateur

ATTENTION

IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL

OR CALL CUSTOMER SERVICE BEFORE YOU RETURN

THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.

For Customer Service: email: par[email protected]

in English Call: 866-661-1218

in Spanish Call: 866-661-1218

in French Call: 866-374-9203

ATENCIÓN

SI TIENE ALGÚN PROBLEMA O PREGUNTAS,

ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO

DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER

ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.

Servicio de atención al cliente: Correo electrónico: par[email protected]

Línea para llamadas en inglés: 866-661-1218

Línea para llamadas en español: 866-661-1218

Línea para llamadas en francés: 866-374-9203

STOP STOP

PARE PARE

ATTENTION

SI VOUS AVEZ DES PROBLÈMES OU DES QUESTIONS,

ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE

SERVICE À LA CLIENTÈLE AVANT DE RETOURNER

CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.

Pour le service à la clientèle : courriel : par[email protected]

pour le service en anglais, composez le 866-661-1218

pour le service en espagnol, composez le 866-661-1218

pour le service en français, composez le 866-374-9203

ARRÊT ARRÊT

INSTRUCTION MANUAL ENCLOSED

MANUEL D’INSTRUCTION À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

INSTRUCTION MANUAL ENCLOSED

MANUEL D’INSTRUCTION À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

Electric Builder Box

E-1

CONSUMER SAFETY INFORMATION

PLEASE READ THIS MANUAL BEFORE USING THIS APPLIANCE

WARNING

Thank you and congratulations on your purchase of a Classic Flame electric

builder box. Please read the installation instructions before installing and

operating this appliance.

IMPORTANT: Read all instructions and warnings carefully before using.

Failure to follow these instructions may result in a possible electric shock,

ﬁre hazard and/ or injury and will void the warranty.

For Customer Service:

E-Mail: par[email protected]m

In English Call: 866-661-1218

In French Call: 866-374-9203

In Spanish Call: 866-661-1218

Twin-Star International, Inc.

Delray Beach, FL 33483

Made in China

Printed in China

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED,

AN ELECTRIC SHOCK OR FIRE MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE

VAPORS AND LIQUIDS IN THE VICINITY OF THIS

OR ANY OTHER APPLIANCE.

U.S.A.

ELECTRIC BUILDER BOX

MODEL NUMBERS:

INSTALLATION GUIDE

52EB497GRA

LISTINGS AND CODE APPROVALS

THE BUILDERS BOX SERIES HAS BEEN TESTED AND APPROVED IN ACCORDANCE WITH

CSA AND UL STANDARD.

MODEL SPECIFICATIONS

MODEL

NUMBER DESCRIPTION VOLTAGE AMPS

120 25 YES 0.25

52EB497GRA

!!! WARNING !!!

STEP - BY - STEP INSTALLATION OVERVIEW

(Please read all instructions before installation)

52” STANDARD

RATED POWER

WATTS

REMOTE

CONTROL

THE INSTALLATION OF THE BUILDER BOX MUST COMPLY WITH THE APPLICABLE

LOCAL AND / OR NATIONAL ELECTRICAL CODES AND UTILITY REQUIREMENTS.

THIS INSTALLATION SHOULD BE ENTRUSTED TO ONLY QUALIFIED

PERSONNNEL WHERE REQUIRED BY LAW.

Section 1.) Prepare product for installation.

Section 2.) Rough in framing following the recommended dimensions.

Section 3.) Mount the unit.

Section 4.) Wire the unit to the power supply.

Section 5.) Wire the control box.

Section 6.) Function check.

Section 7.) Finish wall construction.

Section 8.) Finalize product installation.

Section 9.) Electric wirng diagram.

E-2

SECTION 1: PREPARATION

1.) Open the master carton, stone box , side panel boxes and wall mounted control box

are on the top of product, take them out and put them in a safe location( see figure 1.)

2.) Cut the master carton along the cut line shown on the box, open the box.

3.) Take off the styrofoam ends from the builder box. Put the product over a big flat surface

with a raised flat blocks underneath the product to keep the product flat.

Recommended size of blocks are L 60 in x D 15 in x H 2 in ( see figure 2.)

4.) Unscrew 2 screws on the top edge of the frame. Securely holding the frame lift up and pull

away from the unit to remove the frame. Do not remove the protective plastic film at this time.

Place the frame in a safe place( see figure 3.)

E-3

60"

15"

Figure 2

Side panel

(2 pcs)

Wall mounted

control box

AUTO

UPLIGHT

DOWNLIGHT

FLAME

Remote

Stones

Builder box

Figure 1

Figure 3

Section 1: Framing

Model A B C D E F G H I J K L M N

52EB497GRA 11 51 18 20 17 52 49 50.5 17.4 10.2 1.5 73.4 52 52

Framing Specification: Figure 4

SECTION 2: FRAMING

Built the framing according to the specifications shown in the below table & figure 4.

SECTION 3: MOUNTING

There are two secure methods to mount the unit to the framing:

Method # 1: Use 4 mounting tabs ( see figure 6 & 7.)

Method # 2: Use the mounting holes ( see figure 8 & 9.)

E-4

MOUNTING TABS

Method 1:

1.) The tabs are shipped flat, bend them out at a 90° angle ( see figure 5.)

2.) Insert the builder box into the opening in the framing.

3.) Secure the tabs to the framing using screws (see figure 6 & 7.)

E-5

Bend 90

to outside

Tabs

bending 90

Figure 5: Mounting Tab Location Figure 6: Wall and Mounting Tabs

Figure 7: Mounting Tolerances - Top View

STUD

WOOD OR METAL

MOUNTING TABS

DRYWALL/SHEETROCK

DRYWALL / SHEETROCK

STUD

FRONT

MOUNTING TAB

916

E-6

Method 2:

1.) Insert the builder box into the opening in the framing .

2.) Secure the builder box to the frame directly using the screws ( see figure 8 & 9.)

Figure 8

Figure 9 : Builder Box Side View

FRONT

DRYWALL/ SHEETROCK

MOUNTING SCREWS

FRONT FRAME

BUILDER BOX

HOUSING

STUD

SECTION 4: WIRNG MAIN BOX

1.) Loosen the screw securing the junction box cover abd remove the cover.

2.) Pull the power supply wires through the hole in the cover.

3.) Pull out the 6 wires marked L, N, G, K1, K2, S from the junction box on the

builder box.

4.) Connect the black L wire from the unit to the black L from the power supply.

5.) Connect the white N wire from the unit to the white N from power supply.

6.) Connect the green ground wire from the unit to the ground from the power supply.

7.) Ensure that all connections are tight. ( see figure 10)

E-7

Figure 10

18AWG WIRE

( NOT SUPPLIED)

SIGNAL CABLE (SUPPLIED)

SIGNAL CABLE

Juction box cover

Builder Box

Black

White

Green

Black

Green

White

18AWG WIRE FROM

POWER SUPPLY

(NOT SUPPLIED)

Orange

Black

SECTION 5: WIRNG CONTROL BOX

1.) Mount one standard single gang junction box in the wall.

2.) Prepare 2 orange 18AWG wires, pull one end through the hole on the cover of junction box.

3.) Connect one of orange wires to K1 from the unit.

4.) Connect another orange wires to K2 from the unit.

5.) Find the signal wire which was provided with product. Pull the end through the hole on

the cover of junction box.

6.) Plug the wire marked S into the unit.

7.) Insert all wiring black into the junction box on the unit and secure with a wire tie.

8.) Pull the other ends of 2 orange 18AWG wires and signal wire through the hole on wall

outlet.

9.) Connect one of the orange wires to C1 from the control box.

10.) Connect another orange wire to C2 from the control box.

11.) Plug the signal wire into the control box.

12.) Secure the control box to wall outlet.

13.) Ensure that all connections are tight. ( see figure 11)

E-8

Figure 11

Control

Box

Wall outlet

Juction box cover

Builder box

Black

EXTENSION SIGNAL CABLE (SUPPLIED)

SIGNAL CABLE

Orange

Black

18AWG WIRE

(NOT SUPPLIED)

Black

Orange

SECTION 6: CHECK & TEST

1.) Recheck all the wiring work, make sure all connections are tight and correct to this

manual.

2.) Switch on the power supply to the unit.

3.) On the control box switch the ON/OFF switch to the ON position.

4.) Using the wall controls, test all the functions to ensure they are correctly working.

If any functions do not work correctly recheck the wiring using sections 4 and 5

of this guide.

5.) Use the remote control to operate the unit, check all the functions.

Now the unit has been correctly wired.

6.) Slide the switch on the control box to the OFF position.

7.) Switch off the power supply to the unit.

SECTION 7: WALL FINISH

Finish wall construction work. Refer to figure 6 in section 3 for reference.

SECTION 8: COMPLETION

1.) Remove the protective film from the front frame of the unit.

2.) Open the slide panel brick box and identify left panel & right panels.

3.) Mount the side panels into the unit. The panels have magnets on the back that

hold the panels in place (see figure 12.)

4.) Open stone box and clean the stones. Place both the clear and white stones on the

shelf, mixing the two stone types evenly (see figure 12.)

5.) Securely holding the frame, line up the 3 pins on front frame with the holes on the unit.

Insert the pins into the holes and carefully lower the frame; the frame will seat down

into place (see figure 13.)

6.) Secure the frame with 2 screws.

E-9

Figure 12

pins

screws

side panel

stones

Figure 13

Table des matières

Langues :

Autres manuels Classic Flame Cheminée intérieure

Classic Flame

Classic Flame 23EF024GRA Manuel utilisateur

Classic Flame

Classic Flame CFI-950-4 Manuel utilisateur

Classic Flame

Classic Flame 36EB110-GRT Manuel utilisateur

Classic Flame

Classic Flame 18EF010GAA Manuel utilisateur

Classic Flame

Classic Flame 42II042FGT Manuel utilisateur

Classic Flame

Classic Flame 39EB500ARA Manuel utilisateur

Classic Flame

Classic Flame 39EB500ARA Manuel utilisateur

Classic Flame

Classic Flame 33EB304GRS Manuel utilisateur

Classic Flame

Classic Flame 26MM9872 Manuel utilisateur

Classic Flame

Classic Flame 36EB110-GRT Manuel utilisateur

Classic Flame

Classic Flame Helen Manuel utilisateur

Classic Flame

Classic Flame 26MM6501 Manuel utilisateur

Classic Flame

Classic Flame 45EB424GRS Manuel utilisateur

Classic Flame

Classic Flame 36EB110-GRT Manuel utilisateur

Classic Flame

Classic Flame 18E01 Manuel utilisateur

Classic Flame

Classic Flame 36EB110-GRT Manuel utilisateur

Classic Flame

Classic Flame 33EB304GRS Manuel utilisateur

Classic Flame

Classic Flame CFI-763-01 Manuel utilisateur

Classic Flame

Classic Flame 26MMS9872 Manuel utilisateur

Classic Flame

Classic Flame 47IMM4931 Manuel utilisateur

Classic Flame

Classic Flame 23IIU42FGL Manuel utilisateur

Classic Flame

Classic Flame 26MM9856 Manuel utilisateur

Classic Flame

Classic Flame 34HF600GRA Manuel utilisateur

Classic Flame

Classic Flame 26MM90273 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation