Classeq ECO 2 Guide de l'administrateur

Installation

Operators Manual

Eco, Hydro and Duo

under counter range

Part number 902.0001

Revision E

Installation and Operation instructions

For ‘Classeq’ under counter range of glass and dishwashers.

Section Title Page(s)

1Safety instructions 1

2The appliance 2

3Installation 2 -5

4Commissioning 5 -8

5Operation 8 -11

6Cleaning 12,13

7Trouble shooting 13 -15

CAREFULLY READ THESE INSTRUCTIONS, BEFORE

INSTALLING AND OPERATING THIS APPLIANCE.

INCORRECT INSTALLATION, ADAPTATIONS OR

ALTERATIONS COULD RESULT IN INJURY OR DAMAGE TO

PROPERTY.

MALICIOUS DAMAGE, DAMAGE DUE TO NEGLIGENCE, OR

FAILURE TO COMPLY WITH THESE INSTRUCTIONS AND

LOCAL LEGISALTION, OR UNAUTHORISED TAMPERING

WILL INVALIDATE ANY WARRANTY AND RELIEVE THE

MANUFACTURER OF ALL LIABILITY

1.0 Safety instructions

1.1 Warning :

1.2 Installation :

Installation should only be carried out by a ‘Classeq’ approved technician,

and in accordance with current regulations and within our instructions.

1.3 Modification :

‘Classeq Limited’ reserves the right to modify either the appliance or the

contents of these instructions without notice.

1.4 Operation :

The appliance should only be used by a trained operator as instructed in

section 5 of this manual.

1.5 Failure / malfunction :

In the event of a failure / malfunction, the mains electrical

and water supplies MUST be isolated at the wall and not

just at the machine.

1.6 Repairs and spare parts :

The appliance must only be repaired by a ‘Classeq’ approved technician,

using genuine ‘Classeq’ spare parts.

Page 1

2.0 The appliance

2.1 Unpacking :

Use suitable means and protective equipment to avoid injury whilst

unpacking and handling the appliance. Remove all outer packaging and

the protective film from the outer panels of the appliance prior to

installation.

Ensure all packing materials are disposed of in accordance with local

regulations.

2.2 Items included :

The following items are included within the appliance

•2 x Baskets

•1 x Cutlery basket (Dishwashers only)

•1 x Water inlet hose

•2 x Primary filters

•2 x Secondary filters (Only 1 on Gravity drain machines)

•1 x Drain plug (Gravity drain machines only)

•2 x Bottle weight kits (for Rinse Aid and Detergent tubes)

•1 x Installation and Operation Instructions (Must be left with the

customer)

•1 x Warranty card (Must be left with the customer)

3.0 Installation

3.1 The site :

Ensure that there is sufficient space for the installation, servicing and easy

access to all mains isolator switches / valves (i.e. electricity and water).

Ensure that the surface the appliance is going to be installed onto is

adequately stable and capable of supporting the appliance during normal

operation, listed below are the approximate machine weights when fully

laden during normal operation.

Once installed ensure that the appliance is stable and secure, with its

weight being distributed equally and does not tilt more than 3° in any

direction.

Machine sizes Weight

400mm² basket 90 Kgs

500mm² basket 135 Kgs

Page 2

3.2 Electrical connection :

All electrical connections MUST be carried out by an authorised

technician and in accordance with local regulations.

As a minimum ‘Classeq’ recommends that the following standards are

maintained :

•All appliances are connected via a residual current device

(R.C.D.) or earth leakage protection device.

•EN 60204

Supply isolator switch must have all pole separation of more

than 3mm.

•EN 60335

The appliance must be connected to a equi-potential

conductor, the connection stud is located at the rear of the

appliance (a suitable ring terminal shall be required), this is in

addition to the earthed electrical supply.

Prior to connecting the appliance, ensure that the voltage and the supply

fuse complies with the rating plate on the appliance.

3.2.1 Electrical rating :

Within the ‘Classeq’ range several of the 500mm² basket appliances can

be either down rated or up rated electrically, such a procedure MUST be

carried out by a ‘Classeq’ approved technician.

The down / up rating of the machine is carried out by configuring the

terminal block within the appliance to the following

13 Amp –Single phase

•Links removed between L1, L2 and L3

•Ensure link remains between neutrals (N)

30 Amp –Single phase

•Ensure all link remains between lives

terminals (L1, L2 and L3)

•Ensure link remains between neutrals (N)

Three phase

Only Eco3, H750, Duo3 and Duo750 appliances can be converted to three phase,

such conversion must be carried out in accordance with instructions WI-PROD-001A

Page 3

3.3 Water connection :

The appliance comes with a water supply hose requiring a ¾” BSP male

threaded connection at the mains water supply, upon installation and

commissioning all water joints must be checked for leaks).

3.3.1 Water supply restrictions :

Water supply constraints must be adhered to :

•Incoming water temperature

•4°c minimum

•55°c maximum

•Supply water dynamic pressure (air break machines, minimum water pressure

0.25 bar, all other parameters apply).

•0 to 2 bar Rinse booster pump required

•2 to 4 bar No modifications required

•4 to 6 bar Flow restrictor required

•6 bar plus Pressure reducing valve required

If the above requirements are not adhered to, the performance of the appliance

will be impaired

3.3.2 Drainage systems

Appliances are available as either gravity drain or pumped drain, upon

installation the waste hose and stand pipe must be configured as shown within

this manual, also all installations must be with a running / ‘P’ trap to ensure

hygiene, to identify your appliance see page 9 of this manual :

Drain pump machine

•Ø40mm (Ø1 ½”) standpipe required

•Standpipe must be 100 to 150mm

(4” to 6”) below the top of the

appliance.

•The end of the waste outlet hose in

the standpipe must not be lower

than the bottom of the door.

•The waste outlet hose must be a

loose fit within the standpipe.

Page 4

Bleeding of drain pump

After installation and once the tank is partially filled, i.e. before the 1st wash

cycle the drain system MUST be ‘BLED’, simply lower the drain hose into an

empty bucket and allow approximately 4 litres of water to flow out of the hose,

carefully return the hose to the stand pipe as shown above. Ensure any spillage

is cleaned before leaving the appliance.

Gravity drain machine

•Flexible waste hose must

be securely attached to

the waste outlet elbow on

the rear of the machine.

•The waste hose must

flow down from the waste

outlet elbow to the drain.

•Ø35mm (Ø1 ¼”) stand-

pipe required, must be

lower than the baseline

of the appliance

•H800 standpipe must be

a minimum of 75mm (3”)

below the baseline of the

appliance.

4.1 Rinse aid & detergent :

Ensure chemical tubes are attached correctly to the individual chemical

pumps (pumps located behind front lower panel of the appliance).

At the bottle end of the chemical tubes, slide the bottle weight onto the

tube, now place the tube and bottle weight into the correct chemical

bottle.

Ensure the correct chemical tubes now go to the corresponding chemical

bottles.

WARNING : Only rinse aids and detergents developed for commercial

glass and dishwashers are to be used, rinse aids must be suitable for

water temperatures down to 40°c.

4.0 Commissioning

Page 5

•Hose to be a close / tight fit into the drain pipe to reduce odours from the

drain system

4.1.2 Detergent / Soap prime :

The detergent / soap pump system on these appliances is self

priming.

4.1.3 Chemical dosage :

Chemical doses are pre-set to the following nominal values,

however these values should be calibrated to suit individual sites

requirements

Pre-set values (in seconds)

4.1.1 Rinse aid prime :

•Switch machine ON and allow to fill

•Remove the lower front panel (do not

to touch any wire connections).

•Depress and hold button located on

the chemical pump bracket.

•To fully prime, this will take approx 1 ½

minutes.

•Replace the front lower panel.

Machine sizes Rinse aid

Cycle Detergent

Initial Cycle

Eco 2 & Duo 2 540 10

Eco 3 & Duo 3 570 10

Hydro500 & Duo 500 540 10

Hydro700, Hydro750 & Duo 750 545 10

Adjustment of chemical dose is via the timer located under the top

panel of the appliance, the timer allows the following values to be

calibrated to suit the sites requirements

Page 6

Rinse aid pump Soap pump

The chemical timer allows the following dosing to be adjusted

•Cycle rinse aid

•Cycle detergent / soap

•Initial detergent / soap

4.2 Rinse & wash tank temperatures :

The water temperatures on ’Classeq’ range of machines is none adjustable.

Machine type Temperatures

Rinse water Wash water

Glasswashers 70°c

55°c

Dishwashers 80°c

4.3 Interlock options :

All appliance now have the following three interlock options, to select such an

option remove the front lower panel, towards the centre of the machine you will

find four cables tied together, each wire with a different coloured cover (black,

green, red & white), by connecting different combinations together you will

obtain the appropriate interlock option

•Interlock removed

Will start at any temperature

Connect the Black crimp to the White crimp

•Quick start (default setting)

Will start if the rinse tank is above 55°c

Connect the Green crimp to the White crimp

•Interlock

All tanks must be up to temperature, before a cycle will start

Connect the Red crimp to the White crimp

Page 7

P1 = Detergent / Soap

pump

P2 = Rinse aid pump

4.4 Demonstration :

‘Classeq’recommends that prior to leaving the site / installation, the installer

demonstrates the following to the end user, as this will ensure the appliance is

correctly used

•What to do in case of an emergency, i.e. how to isolate the mains

electricity and water (see section 1).

•Switching the appliance on.

•Operating the appliance.

•Draining down.

•Switch the appliance off.

•Clean the appliance, including removal and replacement of all filters.

•Replenishing and priming of rinse aid and detergent.

5.0 Operation

5.1 Machine description :

The design of commercial glass and dishwashing machines differ from

their domestic versions as they are designed to run nearly continually for

many hours.

Commercial appliances, wash results can be effected by external

considerations such as incoming water temperature, pressure, hardness

and choice of chemicals, ‘Classeq’ recommends that your appliance is

either connected to a water softener or a softened water supply, for

further details on water softeners please contact the supplier of your

appliance.

Upon completion of the installation and commissioning of the appliance,

this manual MUST be left with the end user.

Page 8

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Classeq Lave-vaisselle

Classeq

Classeq CST Guide de démarrage rapide

Classeq

Classeq P500 Manuel utilisateur

Classeq

Classeq D 400 Manuel d'instructions

Classeq

Classeq DUO 750 Guide de l'administrateur

Classeq

Classeq DUO 750 Instructions d'installation

Classeq

Classeq D12000 Instructions d'installation

Classeq

Classeq G 350 Manuel utilisateur

Classeq

Classeq P500 Manuel d'instructions

Classeq

Classeq HYDRO 850 Manuel utilisateur

Classeq

Classeq H750 Mode d’emploi

Classeq

Classeq D 400 Manuel d'instructions

Classeq

Classeq G 350 Guide de démarrage rapide

Classeq

Classeq D 400 Manuel utilisateur

Classeq

Classeq ECO 3 Instructions d'installation

Classeq

Classeq P500A Manuel utilisateur

Classeq

Classeq P500AS Manuel utilisateur

Classeq

Classeq CST 100 Instructions d'installation

Classeq

Classeq C200G Guide de l'administrateur

Manuels Lave-vaisselle populaires d'autres marques

Electrolux

Electrolux ESI5211LOX Manuel utilisateur

KitchenAid

KitchenAid KUDB230B Manuel utilisateur

Brandt

Brandt BDJ424DB Manuel utilisateur

Asko

Asko DSD767UXXL.AU Manuel utilisateur

Beko

Beko DFN26210W Manuel utilisateur

NEFF

NEFF S153ITX00E Fiche technique

Midea

Midea SV 4.45 wi Manuel utilisateur

LG LDF7932 Manuel utilisateur

Gorenje

Gorenje GV63214 Manuel utilisateur

Hotpoint

Hotpoint HDA1100ZWH Manuel de service

Blomberg

Blomberg LDFN2240W Manuel utilisateur

AEG

AEG FFB83836PM Manuel utilisateur

Cylinda

Cylinda DM3220RFD Manuel utilisateur

Atag

Atag DW8214MB Manuel utilisateur

GE GLD8000 Series Manuel utilisateur

Siemens

Siemens SN23HI02KE Fiche technique

Omega

Omega ODW717X Manuel utilisateur

BORETTI

BORETTI BVW-683 Manuel utilisateur