Clarus Fusion Series Manuel utilisateur

MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347

SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624

Visit our web site:

clarusenvironmental.com

Product information presented

here reects conditions at time

of publication. Consult factory

regarding discrepancies or

inconsistencies.

SEE LIST BELOW FOR

WARNINGS

Thank you for choosing a Fusion®Series Treatment System. High quality

workmanship and easy maintenance have been incorporated into the

Fusion®system. The system will provide years of trouble-free service

when maintained according to the manufacturer’s recommendations.

Please read this manual in its entirety before using the Fusion®, and follow

all instructions to ensure proper operation. Keep this manual for future

reference along with other important onsite documents. Should further

assistance be necessary, please contact Clarus Environmental at 1-800-928-

7867 or +1-502-778-2731.

Warning Labels

You will nd warning labels on the Fusion®, riser lids, blower, and the alarm

control panel. It is very important to follow the information on these labels

to ensure your safety. Please do not remove these labels.

1. DO NOT attempt to service the Fusion®unit yourself. Contact your

authorized maintenance provider for all service related issues.

2. There are buried electrical cables and piping near and around the

Fusion®. Please consult your authorized maintenance provider to

locate these utilities before excavation.

3. DO NOT bury or cover the Fusion®lids with soil or other debris. This is

necessary to allow access for operation and maintenance of the unit.

4. The Fusion®blower must be unobstructed and vented for proper

operation. Care must be taken that no grass clippings or other

materials accumulate on or around the blower and block ventilation.

5. DO NOT place heavy objects over the Fusion®or drive heavy

equipment over the Fusion®, as damage may occur. Damage of this

kind is not covered by the warranty.

6. DO NOT plant trees within 15 feet (4.6 m) of the Fusion® Series

Treatment System.

Fusion®Series Treatment Systems

SECTION: C3.10.140

CL0056

0320

Supersedes

1219

OWNER'S MANUAL

Manufacturer warrants, to the purchaser and subsequent owner during the

warranty period, which is retroactive to the date of June 1, 2014 for previously

installed Fusions, the Fusion Fiberglass Tank only to be free from defects in

material and workmanship under normal use and service, when properly

installed, used and maintained, for a period of ten (10) years from date of

purchase by the end user. Tanks that fail within the warranty period that

inspections determine to be defective in material or workmanship, will be

repaired, replaced or remanufactured at Manufacturer’s option, provided

that by so doing the manufacturer will not be obligated to replace the entire

assembly or the complete unit. No allowance will be made for shipping charges,

damages, labor or other charges that may occur due to product failure, repair

or replacement.

All other Fusion components including the blower and alarm panel will be

warranted for a two-year (2) period from date of purchase by the end user.

This warranty does not apply to and there shall be no warranty for any material

or product that has been disassembled , subjected to misuse, misapplication,

neglect, alteration, accident or act of God; that has not been installed, operated

or maintained in accordance with Manufacturer's installation instructions;

that has been exposed to outside substances including but not limited to the

following: tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents,

etc.), or other abrasive or corrosive substances that can damage the berglass

material. The warranty set out in the paragraph above is in lieu of all other

warranties expressed or implied; and we do not authorize any representative or

other person to assume for us any other liability in connection with our products.

Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky 40211,

Attention: Customer Support Department to obtain additional information

pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,

CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF EXPRESSED

OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO

THE DURATION OF THE EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty,

so the above limitation may not apply to you. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

This warranty gives you specic legal rights and you may also have other rights

which vary from state to state.

LIMITED WARRANTY

Fusion®Model: ZF-450 ZF-800

Serial No. ____________________________________

Installing Contractor ____________________________________

Phone Number ____________________________________

Installation Date ____________________________________

Maintenance Provider’s Name ____________________________________

Phone Number ____________________________________

Limited Warranty ................................1

Process Description ..............................3

System Components and Care .......................3

Excavation and Installation..........................6

Start Up ......................................9

Blower Timer Setting ............................ 11

Operation and Maintenance ........................ 12

Aeration Chamber Cleaning ........................ 14

Fusion®Pumping................................ 15

Troubleshooting ................................ 16

TABLE OF CONTENTS





Clarus Environmental Product

on our website:

http://reg.clarusenvironmental.com/

PRELIMINARY

INFLOW

RECIRCULATION BAFFLE

EFFLUENT

AERATION

(BLUE)

BACKWASH

(RED)

SLUDGE RETURN

BAFFLE

RECIRCULATION WALL OPENING

INFLOW

BAFFLE

BACKWASH MECHANISM

RECIRCULATION WALL OPENING

BAFFLE

EFFLUENT

6" (152mm) STONE OR CONCRETE PAD

W.L W.L W.L

W.L

G.L G.L

SIDE VIEW

TOP VIEW

The Fusion®is simple in design, yet advanced in its wastewater

treatment ability. The design has been rened over many years

of intense research and development in an effort to perfect this

superior treatment system. Fusion® systems are 90% - 95%

efcient at treating wastewater. This is nearly twice as effective

as a traditional septic tank, which is approximately 50% efcient.

This high degree of treatment helps to protect both your personal

property and the environment.

The Fusion®utilizes a combination of anaerobic (without oxygen)

and aerobic (with oxygen) biological processes to treat wastewater.

As wastewater enters the Fusion®, it is broken down and becomes

food for biological organisms benecial to bacteria operating

within the unit. The rst chamber serves to separate grease and

large solids from the liquid. In the second chamber, plastic media

with large surface areas are used to increase contact between

water and benecial bacteria to optimize treatment. A small linear

air blower is used to move air (oxygen) into the third chamber

for the aerobic process. The nal efuent leaving the system will

have been treated to secondary quality efuent and will average

*9 mg/L CBOD5and 9mg/L TSS.

* Based on NSF Standard 40 testing.

HOW A FUSION®SERIES TREATMENT SYSTEM WORKS

Anaerobic Chamber -

Organisms adhere to xed lm

media and digest waste

Recirculation Line

Storage

Chamber

Inlet Pipe

4” PVC

SCH 40

(DN 100)

Fiberglass

Sedimentation

Chamber -

Separates bulk

solid and grease

waste

Outlet Pipe

4” PVC

SCH 40

Aeration Chamber

Floating/Circulating

Filter Media -

“Fluidized Bed”

Invigorates aerobic

bacteria

Sludge Return Line

Figure 1 - The following diagram will help you to better understand the process:

Figure 2 - Schematic diagram of the Fusion®Treatment System

SK3194

(DN 100)

PRELIMINARY

The NSF mark displayed here will

be on all NSF Standard 40, Class

1 certied Fusion®systems. The

Fusion®models ZF-450 and ZF-

800 will have the mark displayed

on the alarm panel. Systems not

NSF Standard 40, Class 1 certied,

will not display the mark.

Back-Wash Recirculation

Sedimentation Chamber

Anaerobic Chamber

Aeration Chamber

Storage Chamber

Effluent

Inflow

Figure 3 - Treatment Flow of the Fusion®System.

PROCESS DESCRIPTION

1. Sedimentation Chamber

This chamber is designed to physically separate solids

from the incoming water. Scum is the oating material and

sludge is the material that has settled at the bottom.

2. Anaerobic Chamber

This chamber contains a spherical skeleton-type lter

media, 4.3 inch diameter (109 mm). Through bacterial

growth processes on the surface of the lter media,

biological anaerobic treatment thrives while suspended

solids are captured. Furthermore, the microorganisms

in this chamber convert nitrates in the recirculated water

returning from the aerobic chamber to gaseous nitrogen.

The gaseous nitrogen then escapes to the atmosphere.

3. Aeration Chamber

The aeration chamber consists of an aerated upper section

and a lter media lower section. The chamber is lled with

hollow, cylindrical lter media, 0.6 inch diameter (15 mm)

and 0.55 inches long (14 mm). Biological treatment takes

place on the lter media surface. Aeration is continuous.

Residual suspended solids are captured by the lter media

circulating in this section. During normal operation, a

recirculation line transfers water back to the sedimentation

chamber.

The lter media in the aeration chamber are backwashed

regularly (twice a day, 5 or 10 minute cycle) by the

backwash system located at the bottom of the chamber.

The accumulated sludge is transferred back into the

sedimentation chamber for further digestion.

4. Storage Chamber

This chamber is designed to temporarily store treated water

exiting the aeration chamber. This treated water is ready for

discharge.

The complete wastewater treatment system will typically consist of

the Fusion® treatment components and a soil absorption eld for nal

disposal of the liquid efuent. Some states or counties may require the

addition of a septic tank before the Fusion®to increase the sedimentation

chamber capacity and retain more solids. Please see Figure 11 for a

typical Fusion®system. Variations to the typical system will be made

to suit your particular site and system design needs. Please contact

your authorized Fusion®installer or maintenance provider for further

information about your system design.

Certified to

NSF/ANSI

Standard 40

Class 1

Performance

Designation

Figure 4 NSF STANDARD 40, CLASS 1,

CERTIFICATION MARK

The Fusion®treatment unit utilizes an electronic, dual-port blower

designed specically for use with this system. The blower consists

of a linear motor and two diaphragms to generate the air ow

necessary to aerate and recirculate water within the system. This

style of blower is quieter and more efcient than traditional rotary

vane compressors. Once installed and adjusted, circuitry within the

blower will automatically switch the unit from normal recirculation

mode to backwash mode and back again when appropriate. In the

event of a power outage, the blower will stop, but a backup battery

within the unit will retain the correct time and backwash settings.

THE FUSION®DUAL-PORT BLOWER

SYSTEM COMPONENTS

Blower Part # 5250-0050

RATING

Voltage AC120V

Frequency 60Hz

Insulation class A Rank

Operating time Continuous

CHARACTERISTICS AND PERFORMANCE

Solenoid Valve

off

Solenoid Valve on

Voltage(V) AC120V

Current (A) 1.8 or less 2.0 or less

Power consumption (W) 71 ± 20% 77 ± 20 %

Air volume (L/min) 80 ± 10%

Leak air volume(%) 1.0 or less 2.0 or less

Noice level (dBA) 43.0 or less

Valve movement (N/L) 75.0 or less

Temperature rise 60 deg or less at 30 °C room

temperature

PRELIMINARY

FU S IO N TRE ATM ENT S Y ST EM

450GALLONS/DAY

800 GALLONS/ DAY

BLO WER SER VI ＣE P ART S

COMPLETE BLOWER: P/N 5250-0050-A

BLOWER DIAPHRAGM: P/N 152949-A

BLOWER FILTER: P/N 152950-A

MFG．DATE：

Manufacturer:

Clarus Environmental • 3649 Cane Run Road

Louisville, KY 40211•1-800-928-7867 toll free

ZF 450

ZF 800

□

P/N 018860-E

Certified to

NSF - ANSI

Standard 40

The Fusion®utilizes an alarm panel (see Figure 6) that is designed to

activate an audible buzzer and red beacon light on top of the panel if

there is a drop in air pressure, if a high water alarm condition occurs,

or if the blower does not cycle between recirculation and backwash

modes within the preset time. (Note: Alarm panel can only function

as long as there is electrical power supplied to the panel)

You may from time to time check the proper operation of the alarm

panel by toggling the black switch on the side of the panel to “test”.

The buzzer will sound and the red beacon will light as long as you

hold the switch in the test position. Release the switch for normal

operation.

A dataplate similar to the one in Figure 5 is located on the blower

housing and the alarm panel. There is important information about

the Fusion®on the dataplate, such as the part number, model

number, serial number, and hydraulic capacity. Please make a note

of this information for future reference or in case you should need to

contact your Fusion®maintenance provider.

The contracting installer must mark the installed model number on

the dataplate, the blower housing and the alarm control panel.

Figure 6

P/N

WARNING!

RED BEACON

SILENCE/TEST

SWITCH

BUZZER

FUSION

DATAPLATE

sk2649

LEAKY FIXTURES

It is very important to monitor all water xtures in the home for leaks and

drips and repair them immediately. Leaks can cause tremendous water

use and may hydraulically overload your Fusion®system and reduce

its treatment efciency. Excessive water use may also overload your soil

absorption eld and cause failure.

HIGH USE WATER DEVICES

The draining of hot tubs and swimming pools into your Fusion®system

will cause hydraulic overloading and will impair the treatment efciency.

Please drain these devices to another location. Contact your local

regulatory authorities or authorized Fusion®maintenance provider for

more information. The use of large capacity single ll and drain whirlpool

bathtubs may also cause hydraulic overloading of your Fusion®. Please limit

the use of these types of tubs.

The Fusion®system is designed to continuously operate automatically with

little direct maintenance from the owner. Periodically, a check of the blower

area is recommended to ensure no debris obstructs the ventilation or intake

areas of the blower. Also, periodically test the control panel as outlined under

the alarm panel section. The owner should closely monitor the types and

amounts of substances and products used. Water use should also be closely

monitored to ensure proper operation of the Fusion®system.

Periodically, more extensive maintenance must be performed. Your authorized

Fusion®maintenance provider will oversee this service. The name of the

maintenance provider can be recorded on the front of this document and should

also be located on the alarm panel. For more information see the Operation and

Maintenance section of the manual.

The owner should only perform minimal routine maintenance on the Fusion®

such as clearing debris from around blower housing (leaves, snow, and grass

clippings). The Fusion®should also be protected from excessive weight such

as vehicular trafc. Trees and bushes should not be planted in close proximity

to the Fusion®. The Fusion®should be accessible to maintenance personnel

and the riser lids must never be buried.

ALARM PANEL

DATAPLATE

FLOODING

If ooding of the Fusion®occurs and the blower or the

alarm panel is submerged, please disconnect power at the circuit breaker.

DO NOT try to reconnect power to either the blower or alarm panel once

it has been submerged. Immediately contact your authorized Fusion®

maintenance provider to inspect the Fusion®, the blower, and the alarm

panel. Your maintenance provider will repair or replace the components as

needed.

Figure 5

SYSTEM CARE

sk2933

Figure 7

12 3 4 5 6 7 8

TB2

120 VAC L1

INCOMING N

POWER GND

DISNF

ALARM

HIGH WATER

ALARM

BLOWER

*FOR ILLUSTRATION PURPOSES ONLY*

REFER TO SCHEMATIC LOCATED IN

PANEL FOR INSTALLATION

BLOWER FOR ZF-450 AND ZF-800

GND LUG

The Fusion®system is designed to function even if wastewater does not

enter it for extended periods of time. The power to the blower must remain

on during this time for the system to function properly. Weekend use will

not harm the system as long as the blower is on. Should seasonal use

require a complete shut down of the property, then it is recommended that

the blower be turned off. It is important to start up the system in advance of

actual occupancy to allow for normal treatment to resume. Please contact

your authorized Fusion®maintenance provider for further information

concerning shut down and startup of the Fusion®. You may also contact

your maintenance provider for the shut down and startup services.

INTERMITTENT USE

PRELIMINARY

The Fusion®is designed to treat household type waste and can

treat most common substances introduced into the system.

However, certain harmful substances may reduce the efciency

or stop the treatment process by reducing or destroying the

benecial bacterial populations responsible for treatment. In

general, if a chemical substance is considered harmful to humans

then it should also be considered harmful to the Fusion®treatment

system. If you have any questions concerning the use of any of

these substances, please contact your Fusion®maintenance

provider. The introduction of any substance on the “Do Not" List

into the Fusion®will void the warranty.

- THE "DO NOT" LIST -

DO NOT introduce the following substances into the Fusion®

treatment system:

• Motor oil • Antifreeze

• Brake uid • Paint

• Paint thinner • Gasoline

• Solvents • Pesticides

• Herbicides • Strong disinfectants

• Strong caustic drain • Toilet tank

cleaners in excess disinfection chemicals

• Excess pharmeceuticals • Chemicals & chemical

waste

Not Recommended: Trash and excess food products will likely

increase frequency of pumping.

Trash

• Sanitary napkins and • Condoms

feminine products • Cat litter

• Diapers • Dental oss

• Paper products such as • Cigarette butts

paper towels & baby wipes • Plastic/rubber products

Food Products

• Coffee lters and grounds • Greases or lards

• Fruit and vegetable peels • Seeds

• Meat products • Bones

• Garbage disposal waste • Egg shells

Limited Use Products

Certain products in small or moderate amounts should not

disrupt the Fusion®treatment process. You should always use the

minimum quantities of these substances as recommended by the

manufacturer.

• Liquid laundry bleach only as needed per load

• Liquid laundry detergents without added bleach

• Liquid dishwashing detergents

• Household cleaners

If water softners are present in the home, Clarus Environmental

recommends the use of water and salt conservative models that

are installed and operated correctly. If you have questions about

softeners, contact the Water Quality Association at www.wqa.

org. Contact factory for installation details.

HARMFUL SUBSTANCES

WATER SOFTENERS

AUTHORIZED MAINTENANCE PROVIDER

Your authorized maintenance provider will perform many system

checks and adjustments as needed during the maintenance inspection.

Two inspections per year will be made for a total of four inspections

during the initial service policy. Please see the Operation and

Maintenance section of this manual for further details.

Should there be any operational deciencies with your Fusion®,

the maintenance provider will notify the owner in writing when

the deciencies will be corrected. If the maintenance provider does

not correct the deciencies or the service calls are not completed,

please contact Clarus Environmental at 1-800 928 2731.

ALARM CONDITION

If an alarm condition occurs, please check the air intake area

around the blower and make sure no debris blocks the blower

intake. Remove the air lter cap by removing the screw from

the cap and then pulling on the sides of the top of the blower.

Remove the foam lter and gently tap against your other

hand. If it is very clogged wash it in warm, soapy water and

dry well before replacing. Reassemble lter and cap on top of

blower. Do not attempt to remove the blower housing or any

other parts from the blower. If the blower is operating properly,

there may be a high water condition within the Fusion®. It

may be necessary to discontinue water use until the alarm

condition has been resolved. If the buzzer continues to sound

or the red light stays on, please contact your authorized Fusion®

maintenance provider. The buzzer may be silenced by toggling

the black switch on the side of the alarm panel to “silence”.

The red beacon light will remain on until the problem has been

resolved.

POWER OUTAGE

Should you experience a power outage, the blower will not

operate and air (oxygen) will not be supplied to the Fusion®. If

the blower is off for more than 24 hours, the lack of fresh air will

cause the treatment efciency to decrease. During a power outage,

the Fusion® will still allow efuent to ow, and will not create a

backup in the home. You may, however, have a pump or dose tank

with a pump on the outlet of the Fusion®, which requires power to

pump the efuent to the soil absorption eld. If you have a system

such as this, please be aware of this condition and conserve water

accordingly.

Fusion® Series systems are compact, efcient, and designed to

be installed in a typical residential/light commercial environment.

The nal efuent leaving the system will typically be treated to the

secondary quality strength of *9 mg/L CBOD5and 9 mg/L TSS.

EFFLUENT QUALITY

*Based on NSF/ANSI Standard 40 testing.

INSPECTION AND MAINTENANCE

FREQUENCY

Fusion®Series systems are to be inspected and maintained every

six months under normal usage. The inspection and maintenance

are only to be performed by personnel trained and authorized by

Clarus Environmental. A Maintenance & Service Report (CL0059)

is to be completed for each inspection and maintenance visit.

An extended maintenance policy is available for purchase from

your authorized Fusion®distributor. The extended maintenance

policy will include the same system checks, schedule, and

adjustments as the initial maintenance policy. Please contact your

Fusion®distributor or maintenance provider for further information

regarding the extended maintenance policy.

EXTENDED MAINTENANCE POLICY

INITIAL SERVICE POLICY

The Fusion®models ZF-450 and ZF-800 (NSF Standard 40, Class

1 certied systems) have a two-year service policy included in the

initial purchase price. The service policy will include two inspections

per year for a total of four inspections. During these inspections,

numerous system checks and adjustments will be made to ensure

proper operation.

PRELIMINARY

1. Excavate an area large enough for the Fusion®Series unit to be installed. See Figure 8 and Table 3 for the actual dimensions of the

unit. Excavation dimensions are calculated by adding 12-18" (305-457 mm) to the length and width of the Fusion®. This will allow

sufcient room for proper backlling.

2. Construct a 6" (152 mm) thick stone pad of either 1/4" - 1/2" (6-13 mm) diameter stone or concrete pad and level to within 1/8" (3 mm).

3. If the unit is not level, it will cause uneven water ow as well as unbalanced aeration, which will result in poor

performance.

4. Gently lift the unit at all four lifting points with a harness and install it on leveled stone pad (Figure 9).

5. Check unit to make certain it is level by placing a level at several locations on the riser. (riser covers removed) (Figure 9).

1. If groundwater is present, anti-otation measures must be

used to stabilize the unit prior to backlling. Please follow the

procedures in the Anti-otation section to properly anchor

the Fusion®.

2. Fill the unit with clean water to the normal operating depth

prior to backlling. Partition walls between chambers are

water-tight and will ll in succession beginning on the inlet side

of the unit. Therefore, it is best to alternate chambers when

lling with water so the unit remains level. Check for leakage

around the unit.

3. If necessary, install riser extensions on the adapter rings

prior to backlling. See Table 1 for number and size of access

openings. Riser extensions are available for deeper burial.

Make certain risers are sealed properly and watertight.

CAUTION

Apply two beads of silicone fully around each

riser section prior to securing with supplied screws.

5. Install riser covers.

6. Backll with good quality granular soil around the unit that is

free of organic matter, rock, stone, tree roots, or other debris

that could damage the unit.

7. Tamp soil around perimeter of the unit as it is backlled to

stabilize the unit and to reduce settling.

8. Finalize backll with a mounded contour so that surface water

is shed away from the unit. Under no circumstances should

surface water be allowed to accumulate around unit.

CAUTION

MAXIMUM soil burial depth over the unit is 36

inches (914 mm).

EXCAVATION AND INSTALLATION

BACKFILLING

Number AND Size of ACCeSS opeNiNgS iN fuSioN ®SerieS

ZF-450 ZF-800

20" (51 cm) Diameter 0 1

24" (61 cm) Diameter 2 2

Table 1

COLD WEATHER INSTALLATION

When installing Fusion®in cold climates, the designer may

specify insulated lids and risers. In addition, the blower must be

protected from snow drifts. If installed in a riser, the blower must

be protected from inundation and may have a vent pipe installed

to above the maximum snow depth with a 180 degree angle at the

end to prevent snow and water entry. Also, the top and sides of the

Fusion®may be insulated with insulation sheeting or other means

to provide a minimum insulation value of R-8. Please contact the

factory for further information.

ANTI-FLOTATION PROCEDURES

It is necessary to anchor the Fusion®in high ground water

conditions to prevent otation. If groundwater rises above the rock

or concrete pad that the Fusion®sits on, anchoring is required.

Please consult a design engineer, soil scientist or other qualied

individual to determine high groundwater conditions.

1. Follow the procedures outlined in the Excavation and

Installation Section, items 1-5, to properly prepare and level

the Fusion excavation.

2. Follow the procedures outlined in the Backlling Section,

items 1-4 to properly ll the Fusion®with water and add risers

if needed.

3. Refer to Figure 10, Anchoring Schematic to determine the

minimum amount of backll to be placed around the Fusion®

in the excavation. Tamp the ll to prevent settling.

4. Refer to Table 3, Concrete Anchoring Dimensions, to determine

the amount of concrete needed for the concrete anchor collar

that is poured around the entire circumference of the Fusion®.

Pour concrete to the specied dimensions to fully engage

the mid-seam of the Fusion®, which will anchor it once the

concrete cures. Make certain to pour the concrete in a manner

to minimize trapped air within the concrete. Agitating or lightly

mixing the concrete with a metal rod or other similar device

once poured will help release trapped air.

5. Allow the concrete to harden before nal backlling.

6. Complete the procedures outlined in the Backlling Section,

items 5-8.

OUTLET

INLET

1) DIMESIONS "I" AND "E" ARE TO THE BOTTOM

OF THE INLET/OUTLET PIPE.

ADAPTER RING. NOT THE RISER LID.

SEPARATELY.

3) A RISER COVER COMES STANDARD. ADDITIONAL

RISERS ARE PURCHASED

2) THE OVERALL HEIGHT DIMENSION "H" IS TO

THE TOP OF THE NARROW

NOTES:

Figure 8 - Dimensions

Table 2

FUSION®DIMENSIONS

SYSTEM L W H I E

Fusion®450 7'-1" (2.2 m) 3'-8" (1.1 m) 5'-2" (1.6 m) 4'-4" (1.3 m) 3'-10" (1.2 m)

Fusion®800 8'-3" (2.5 m) 4'-8" (1.4 m) 6'-2" (1.9 m) 5'-4" (1.6 m) 4'-10" (1.5 m)

sk2624

PRELIMINARY

4-POINT

LIFTING

LESS THAN 60°

60°

LIFTING

HOOK

LIFTING

LEVEL ACROSS TOP OF UNIT

MANHOLE

FRAME

LEVELING

Figure 9 - Lifting & Positioning

Table 3 - Concrete Anchoring Dimensions

MIN. REQUIRED

BACKFILL

UNIT SIZE Z

18"

21"

ZF-450

ZF-800

CONCRETE ANCHOR

COLLAR

Figure 10 - Concrete Anchoring

sk2931

moDel Nocover 6" (15 cm) cover 12" (30 cm) cover 18" (46 cm) cover

iN (cm)

coNcrete volume

Ft3(m3) (cY)

iN (cm)

coNcrete volume

Ft3(m3) (cY)

iN (cm)

coNcrete volume

Ft3(m3) (cY)

iN (cm)

coNcrete volume

Ft3(m3) (cY)

zf-450 16

(40.6)

(61.0) 72 (2.0) 3 14

(40.6)

(61.0) 62 (1.8) 3 13

(33.0)

(61.0) 56 (1.6) 3 12

(30.5)

(61.0) 51 (1.4) 2

zf-800 20

(50.8)

(61.0) 109 (3.1) 4 19

(48.3)

(61.0) 102 (2.9) 4 40,6

(17)

(61.0) 90 (2.5) 4 16

(40.6)

(61.0) 84 (2.4) 4

moDel 24"(61 cm) cover 30"(76 cm) cover 36"(91 cm) cover

iN (cm)

coNcrete volume

Ft3(m3) (cY)

iN (cm)

coNcrete volume

Ft3(m3) (cY)

iN (cm)

coNcrete volume

Ft3(m3) (cY)

zf-450 12

(30.5)

(61.0) 72 (2.0) 3 12 (30.5) 24

(61.0) 51 (1.4) 2 12 (30.5) 24 (61.0) 51 (1.4) 2

zf-800 12

(30.5)

(61.0) 109 (3.1) 4 14 (35.6) 24

(61.0) 72 (2.0) 3 13 (33.0) 24 (61.0) 66 (1.9) 3

PRELIMINARY

WARNING!

TO DISPERSAL

SEWER LINE

FUSION ALARM PANEL

BLOWER RISER AND LID

FUSION

OPTIONAL SEPTIC TANK INSTALLATION

MAY BE REQUIRED BY LOCAL

OR STATE REGULATIONS

AIR LINES

CLEANOUT

ALARM FLOAT

CONDUIT INSTALLED

BY CONTRACTOR

WHERE APPLICABLE

Figure 11 - Typical Fusion® Layout

sk2650

1. The blower must be connected to a grounded, metallic, permanent wiring system, or an

equipment-grounding terminal or lead on the product.

2. Place the blower where it is easily accessible for maintenance and inspection.

3. Install the blower in an area where it will be protected from damage and inundation. Also

make certain the location has good ventilation.

4. Install the blower on a foundation that is level and solid.

5. Excavate trenches for two air lines from blower to the unit.

6. Install two separate 1/2" (13 mm) air lines from the blower to the unit. Length of piping

must be less than 17' (5 m). If distances from 17' (5 m) to 33' (10 m) are required, use

3/4" (19 mm) diameter piping (Figure 12). If longer air lines are needed, consult the

factory.

7. The blower is provided with two discharge ports. The blower label is color-coded with the

aeration outlet port being BLUE (main) and the backwash (skim) outlet port being RED

(Figure 12).

8. The air port inlets on the Fusion®are also color-coded, BLUE for aeration and RED for

backwash (Figure 12).

9. Attach the barbed end of each PVC tee (included in the blower box) to the blower using the

rubber elbows (Figure 12).

10. Attach the small diameter black air tubing (included in the blower box) to barbed tting

on PVC tee. Black air tubing and blower power cord should be routed to the alarm panel

through conduit. Attach the two black air tubing lines to the two air pressure sensor barbed

ttings in the alarm panel (Figure 12).

11. Connect the remaining end of each PVC tee to the

airlines installed in Step 6.

12. Install the Fusion®blower at an elevation where the

air line outlets are located above the elevation of the

Fusion®air line inlets (Figure 12).

BLOWER INSTALLATION AND PLACEMENT

TO PREVENT ELECTRICAL SHOCK

FROM BACK-SIPHONING, LOCATE

THE PUMP ABOVE THE WATER

LEVEL.

DECORATIVE ROCK CONFIGURATION

INTERIOR CONFIGURATION

DRILL HOLES FOR

BLOWER MAKE UP AIR

Figure 12

ELECTRICALSHOCK

HAZARD

!WARNING

DECORATIVE ROCK CONFIGURATION

INTERIOR CONFIGURATION

RED AIR

LINE

BLUE AIR

LINE

HIGH WATER FLOAT CONDUIT

TO BE INSTALLED BY

CONTRACTOR

(WHERE APPLICABLE)

FUSION UNIT

AIR LINE FROM PUMP

1/2" SCH 40 PVC

BULK HEAD FITTINGS

RUBBER

ELBOWS

POWER

CORD

RED AIR

LINE

BLUE AIR

LINE

CONDUIT TO PANEL

AIR LINE

TO PANEL

ADAPTER

BLOWER

AIR LINES

TO PANEL

SPRING

CLAMPS

DRILL HOLES FOR

BLOWER MAKE UP AIR

ALARM FLOAT

CONDUIT

SEAL AFTER LINE

INSTALLATION

AIR SENSOR LINE

1/2 X 3/4 REDUCER

INSTALL BUSHING IF AIR

LINE IS LESS THAN 17'

TO UNIT

GLUE

FITTINGS

BLOWER

sk2639

PRELIMINARY

There are two aeration systems provided within the aeration

chamber: normal aeration and backwash. Valves (1 and 3) are set

at 50%. Observe the air ow on each side of the unit to verify equal

ow. If there is an obvious discrepancy in air ow between the two

sides, adjust the valves (1 and 3) so that the ow is equal.

CLEAN-OUT

FLOW RECIRC. PIPE

SLUDGETRANSF. PIPE

CLEAN-OUT

ARERATION AIR-IN

(BLUE)

BACKWASH AIR-IN

(RED)

CLEAN-OUT SLUDGETRANSF.

CLEAN-OUT RECIRC.

GREY 0 100

RED 100 100

GREY 0 100

BLUE 100 100

Figure 13 - Aeration Flow Adjustment

1. Connect house sewer pipe or septic tank outlet, if

required, to the unit inlet. Make certain only household

waste enters the unit (no foundation drains, gutter

drains, oor drains, etc.).

2. Connect the outlet pipe to the outlet of the unit.

PIPING INSTALLATION

HIGH WATER ALARM FLOAT INSTALLATION

The Fusion®alarm panel assembly includes a high water alarm

oat switch that is used to monitor the liquid level in the Fusion®

unit. The switch should be tethered to one of the gray, vertical

air lines in the aeration chamber with a 3" (76 mm) tether

length. The cord should pass through the opening in the partition

wall between the aeration and anaerobic chamber and allow

the oat to hang in the outlet bafe of the anaerobic chamber.

1. The oat switch should be tethered to one of the gray,

vertical pipes in the aeration chamber. When the oat is

in the horizontal position, the cord should be at least 1"

(25 mm) below the top of the partition wall opening in

the anaerobic chamber bafe.

2. Place the cord into the clamp and secure to gray aeration

pipe. NOTE: Do not install the cord under the clamp.

3. Position the oat with a 3" (76 mm) tether.

4. Tighten the clamp with a screwdriver. Be careful not to

overtighten as this may cause damage to the plastic clamp.

5. Make sure the oat cord is not allowed to touch the

excess clamp band during operation as this may cause

damage to the cord.

6. The oat switch cord should be installed in an electrical

conduit connecting the alarm panel to the Fusion®unit. The

electrical conduit must be rated for burial, and should be

properly sealed to prevent gases from entering the alarm

panel.

7. A 1/2" (13 mm) bulkhead tting (supplied by others) should

be used to connect the electrical conduit to the Fusion®unit.

A hole must be drilled through the wall of the Fusion®unit

between the red and blue bulkhead ttings to facilitate

this connection.

8. Please be certain that the bulkhead tting for the electrical

conduit forms a watertight connection with the FRP wall

of the Fusion®unit.

9. Electrical conduit from the Fusion®unit to the alarm

panel can be buried in the same trench as the air lines.

10. The control switch can be wired directly into the alarm

panel. See Figure 7.

1. All electrical installations must follow the

National Electrical Code and/or your local/state electrical

codes.

2. The blower should be directly wired into the alarm panel.

The alarm panel must be located in a dry location that is

accessible for maintenance. Please see Figure 7 and the

wiring diagram and instructions enclosed with the alarm

panel.

3. Make certain the timer within the control panel is set to the

proper time. The timer unit display should be set to 10 hrs.

and the timer dial needle set to 3.6 for 36 hours. This will

activate an alarm if the blower doesn't go into backwash

cycle within a 36-hour time frame.

ELECTRICAL CONNECTIONS

START UP

An installation and start-up check list (CL0057)

is furnished with the information package in the blower box.

Please use this as a guide and ll out all sections and return to

your distributor.

Valve Legend:

1. Aeration Blue 3. Backwash Red

2. Recirculation Gray 4. Sludge transfer Gray



PRELIMINARY

The recirculation ow is designed to be 1.2-1.8 times

that of the average design inow. Table 4 indicates

starting ow rates for each unit. However, ne

adjustments may be necessary to ensure optimum

performance.

Setting the flow rate:

• Adjust the ow using rates in Table 4.

• The ow rate is adjusted by rotating the gray

recirculation valve (2) and observing the ow at the

pipe end.

• There are prescribed lines at the outlet of the

recirculation pipe to aid in approximating the correct

ow.

Measuring the flow rate:

• The actual ow rates must be measured to verify

ow after adjustment of the valve and observation

at the pipe end.

• Measure the time in seconds required to ll a 1L

container.

• Compare the time to value ranges in Table 4.

• If necessary, adjust the valve again and collect

another sample to verify the correct ow rates.

In order to prevent plugging of the media in the

aeration chamber, the backwash cycle activates

at a preset schedule. If there is no backwash cycle

or if the backwash cycle is too short, the unit’s

performance will be adversely affected. Likewise, if

the backwash cycle is too long, performance will be

compromised.

The backwash cycle begins at 2:00 AM and lasts for

ve minutes. One hour later, another ve minute

backwash cycle occurs. The backwash initiation

time can be set for any time during a 24-hour period

to accommodate unusual water use patterns. The

goal is to set the time when there is no ow into the

unit.

The backwash cycle and sludge transfer from the

aeration chamber takes place in the same action.

Verify that the air ow is uniform across the

aeration chamber during a backwash cycle. If not,

adjust the red backwash valve (3) accordingly.

Setting the ow rate:

• On all HIBLOW HP series model blowers, press

the [MINUTE] button for at least 2 seconds to

switch to manual mode. The "aeration" and

"backwash" can be switched by the [MINUTE]

button.

• Set the backwash ow rate by adjusting the

gray sludge transfer valve (4). Use Table 5 to

determine the setting for each Fusion®model.

Measuring the ow rate:

• Measure the actual backwash ow rate at the

outlet of the sludge return pipe in the rst

chamber the same way the recirculation ow rate

is measured.

• Adjust the gray sludge transfer valve (4) if

necessary to obtain the proper ow.

• Be sure to press [SET] to return the unit back to auto

mode on HIBLOW Unit.

It is important not to set the ow rate too high

because it can cause excessive agitation within the rst chamber

(Sedimentation Chamber). This could result in poor performance.

RECIRCULATION FLOW ADJUSTMENT BACKWASH FLOW ADJUSTMENT

Table 5 - Backwash Flow Rate Setting

Model Frequency ZF450 ZF800

Backwash ow

rate (sec/liter)

Twice/day 7-10 4-6

Valve open (%) Twice/day 50-55% 40-45%

Figure 15 - Flow

Controlling Valve

Figure 14 - Flow

Measurement

Model ZF450 ZF800

Recirculating ow rate (sec/liter) 29-45 14-22

Suggested Valve Opening 35-40% 30-35%

Table 4 - Recirculation Flow Rates

100

MCL

SUGGESTED

RANGE

RECIRCULATION OR BACKWASH PIPE

CONTAINER

G.L

WATER

TOTREATMENT UNIT

FAUCET

BACKFLOW PREVENTER

HOSE

BLOWER

CLAMP

EXISTING AIR LINE

BRUSH

100

MCL

SUGGESTED

RANGE

RECIRCULATION OR BACKWASH PIPE

CONTAINER

G.L

WATER

TOTREATMENT UNIT

FAUCET

BACKFLOW PREVENTER

HOSE

BLOWER

CLAMP

EXISTING AIR LINE

BRUSH

Autres manuels pour Fusion Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarus Système de filtration d'eau

Clarus

Clarus 5000-0006 Manuel utilisateur

Manuels Système de filtration d'eau populaires d'autres marques

Wisy

Wisy LineAir 100 Manuel utilisateur

Schaffner

Schaffner Ecosine FN3446 Series Manuel d'utilisation

Pentair

Pentair FLECK 4600 SXT Guide de l'utilisateur

H2O International

H2O International H20-500 Manuel utilisateur

Renkforce

Renkforce 2306241 Manuel utilisateur

Neo-Pure

Neo-Pure TL3-A502 Manuel utilisateur

FLTR

FLTR OBF Manuel utilisateur

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manuel utilisateur

Applied Membranes

Applied Membranes W-G844EM Manuel utilisateur

BEGA

BEGA 116 Manuel utilisateur

WATA

WATA Standard Manuel utilisateur

Price

Price FFU series Manuel

Gaggenau

Gaggenau BRITA INTENZA 467873 Manuel utilisateur

Brita

Brita SAFF-100 Manuel utilisateur

HEISSNER

HEISSNER FPU24000-00 Manuel utilisateur

BGS technic

BGS technic 1518 Manuel utilisateur

Reverse Osmosis

Reverse Osmosis RF Series Manuel utilisateur

ubbink

ubbink Filtramax Series Manuel utilisateur