Clarke HARRY Mode d’emploi
WARNING: Read these instructions before using the machine
OPERATION & MAINTENANCE
INSTRUCTIONS
LS0119 - ISS 1
ORIGINAL INSTRUCTIONS
HOT WASHER
MODEL NO: HARRY
PART NO: 7320180
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE Hot Washer.
The machine has been designed to use hot or cold water to clean any
surfaces which can stand the force of the high pressure water jet and the
action of the detergents used.
The machine must only be used for the purpose for which it was designed.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL PROTECTION
Through purchase of this tool, the customer is taking on the obligation
to deal with the WEEE in accordance with the WEEE regulations in
relation to the treatment, recycling & recovery and environmentally
sound disposal of the WEEE.
In effect, this means that this tool must not be discarded with general waste.
Refer to the laws governing Waste Electrical and Electronic Equipment (WEEE)
at a recognised disposal facility.
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
GENERAL SAFETY RULES
1. NEVER direct the spray towards any person or animal.
2. NEVER direct the spray towards electrical wiring or equipment.
3. NEVER hold your finger over the high pressure nozzle.
4. NEVER allow children or untrained personnel to use this machine.
5. NEVER operate the machine with any of the covers removed.
6. NEVER attempt any repairs to this machine. Always refer to your Clarke dealer.
7. NEVER supply any liquid other than water to the water inlet.
8. NEVER use the detergent bottle to introduce flammable liquids/solvents, e.g. paint
thinners, petrol, oil as there is a risk of explosion.
9. NEVER direct the jet at electrical equipment or the machine itself.
10. NEVER use the pressure washer if the power cable or important parts of the machine
are damaged.
11. ALWAYS release any residual pressure in the system by turning off the water supply
and operating the trigger before disconnecting any hose or accessory.
12. ALWAYS keep the machine itself dry and well clear of water spray.
13. ALWAYS wear protective clothing and safety glasses. Loose particles and other
debris may be propelled at high speed by the water jet.
14. ALWAYS grip the gun firmly and expect the spray gun to ‘kick’ when starting.
15. ALWAYS respect the requirements of the local water company. Pressure washers may
only be connected to the mains drinking water supply, if a system separator (known
as a backflow preventer) is installed in the supply hose.
16. ALWAYS disconnect from the water supply and ensure the system is completely
drained when not in use. Store in a cool dry location.
17. ONLY use chemical cleaning agents (detergents), that are approved for pressure
washers. CLARKE Traffic Film Remover or CLARKE Wash and Wax (available from your
dealer), is recommended.
18. WARNING: High pressure water jets can be dangerous if subject to misuse. The jet
must not be directed at a person or anything that they are wearing.
19. WARNING: High pressure hoses, fittings and couplings are important for the safety of
the machine. Only use hoses, fittings and couplings recommended by the
manufacturer.
20. WARNING: Water that has flowed through a system separator (known as a backflow
preventer) is considered non-drinkable.
WARNING: WATER AT HIGH PRESSURE CAN BE DANGEROUS AND CAN
CAUSE DAMAGE IF THE OPERATOR IS CARELESS. NEVER ALLOW ANYONE
TO OPERATE THIS PRESSURE WASHER UNLESS THEY ARE FAMILIAR WITH THE
SAFETY PRECAUTIONS.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ELECTRICAL CONNECTIONS
Before switching the product on, make sure that the voltage of your electricity supply is
the same as that indicated on the rating plate. This product is designed to operate on
230VAC 50Hz. Connecting it to any other power source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to change the
fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or
damaged, the plug must not be used until a suitable replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or due to
damage, it should be cut off and a replacement fitted, following the wiring instructions
shown below. The old plug must be disposed of safely, as insertion into a mains socket
could cause an electrical hazard.
If the colours of the wires in the power cable of this product do not correspond with the
markings on the terminals of your plug, proceed as follows.
• The blue wire must be connected to the terminal which is marked N.
• The brown wire must be connected to the terminal which is marked L.
• The yellow and green wire must be connected to the terminal which is
marked E or .
We strongly recommend that this machine is connected to the mains supply via
a Residual Current Device (RCD).
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.
WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE
COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH
Plug must be BS1363/A approved.
Always fit a 13 Amp fuse.
Ensure that the outer sheath of the cable is firmly held by the clamp
Neutral
(Blue)
Live
(Brown)
Earth
(Green and Yellow)
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
EXTENSION CABLES
If an extension cable is used, always ensure it is fully unwound. When used
outdoors, ensure that the extension cable is specifically designed for outdoor
use. Ensure that the cable is rated for the voltage and amperage of the
machine.
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs
yourself.
SYMBOLS ON THE MACHINE
Read the
manual before
use.
Failing to follow these
instructions could
result in injury or
damage to the
machine.
Conforms to
CE Regulations.
Wear safety glasses
when using this
machine.
Hot Surface
Do Not Touch
Repiritory Hazard.
Always Wear
Protection.
The high pressure jet
must not be directed
at persons, animals,
live electrical
equipment or at the
appliance itself.
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ASSEMBLY
1. Remove all items from the carton.
• The following items should be supplied. If any parts are missing or
damaged, please see your Clarke dealer.
ATTACH THE HANDLE
1. Push the upper handle onto the pins as shown until it clicks into place.
2. Fit the lance holder and cable holder as shown below using the fixing
screws supplied.
1 x High Pressure Cleaner 1 x Gun Assembly
1 x Upper Handle Assembly 1 x Lance & Nozzle Assembly
1 x Lance Holder and 2 Fixing Screws 1 x Detergent Bottle
1 x Cable Holder and 2 Fixing Screws 1 x Hose Adaptor and Water Inlet Flter
1 x High Pressure Hose (8 metre) 1 x Nozzle Clearing Pin
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CONNECT THE HOSE ADAPTOR
1. Insert the Water inlet filter into the
water inlet,
2. Screw the supplied hose adaptor
onto the water inlet as shown.
CONNECT THE HIGH PRESSURE HOSE
1. Push the end of the high pressure
hose into the gun assembly as
shown.
• It will click into place when
secure.
2. Remove the travel cap from the
high pressure hose inlet.
3. Screw the other end of the hose
on to the outlet.
• Tighten the connector hand
tight only;- do not use a
spanner.
• Make sure the connection is
secure.
8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
OVERVIEW
1 Handle 6 Gun
2 OFF/ON/BURNER switch 7 Lance
3 Detergent bottle 8 Diesel tank filler cap
4 Water outlet 9 Power cable
5 High pressure hose 10 Water inlet adaptor + filter
9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
BEFORE USE
FILL WITH FUEL (DIESEL ONLY)
• Always refuel in a well-ventilated area.
• Do not leave fuel within the reach of children.
• Refuel carefully to avoid spillages.
1. Remove the filler cap.
2. Fill the tank with diesel fuel.
• Maximum 1litre.
3. Replace the filler cap securely.
CONNECT TO A WATER SUPPLY
The pressure washer must never be connected to the drinking water supply
without using a system separator (also known as a backflow preventer)
available from most hardware stores.
Always follow the regulations of your local water supplier.
WARNING: INCORRECT FUELS
MUST NOT BE USED AS THEY MAY
PROVE HAZARDOUS.
CAUTION: WATER THAT HAS FLOWED THROUGH A SYSTEM SEPARATOR IS
CONSIDERED NON-DRINKABLE.
10
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
1. Connect a supply hose to the inlet
adaptor.
• We recommend that you use a
push fit quick connector (not
supplied) .
• The water supply must be able
to deliver at least 7.5 l/min with
an inlet temperature not
exceeding 40°C.
ATTACH THE EXTENSION LANCE
1. Push the extension lance into the
gun assembly and rotate it 90
degrees.
2. The detergent bottle may also be
fitted in the same way. (See
“Using Detergents” on page 12.).
GUN ASSEMBLY SAFETY LOCK
1. Push the lock button to prevent
the trigger from being pulled.
2. Push the unlock button to release
the trigger lock.
Table des matières
Autres manuels Clarke Rondelle
Clarke
Clarke POWER WASH PLS220 Mode d’emploi
Clarke
Clarke Tiger Series Mode d’emploi
Clarke
Clarke PLS360 Mode d’emploi
Clarke
Clarke PLS135AH Guide de dépannage
Clarke
Clarke KING 120 Manuel d'installation et d'exploitation
Clarke
Clarke CWM20 Manuel d'installation et d'exploitation
Clarke
Clarke CWM20 Guide rapide
