Clare Controls 1.3 MP Budget Mini Bullet Camera Manuel utilisateur
Doc ID 2014-08-335 • REV 02
Network Camera
Installation Guide
1.3 MP Budget Mini-Bullet Camera
Copyright
© 08AUG14 Clare Controls, Inc. All rights reserved.
This document may not be copied in whole or in part or
otherwise reproduced without prior written consent from
Clare Controls, Inc., except where specifically permitted
under US and international copyright law.
Trademarks and
patents
The 1.3 MP Budget Mini Bullet Camera name is a
trademark of Clare Controls, Inc.
Other trade names used in this document may be
trademarks or registered trademarks of the manufacturers
or vendors of the respective products.
Manufacturer
Clare Controls, Inc.
7519 Pennsylvania Ave., Suite 104, Sarasota, FL 34243,
USA
Version
This document applies to 1.3 MP Budget Mini Bullet
Camera version 01.
i
Contents
Description...1
Package contents...1
Safety instruction...1
Overview...4
Installation...5
Before you start...5
Setting the network camera over the LAN...8
Accessing via web browser...12
System requirement...12
Specifications...17
Regulatory information...19
Contact information...20
ii
1
Description
The 1.3 MP Budget Mini Bullet Camera is an affordable PoE
1.3 MP IP bullet camera for outdoor use. The fixed-lens camera
produces 1.3 MP HD output at 1280 × 960 in low illumination
with an IR LED range of 30m. Features include digital wide
dynamic range, zone-configurable backlight compensation, and
3D digital noise reduction.
Package contents
1X 12 V power supply
3X screws
3X plastic anchors
1X drill template
1X Ethernet weather housing
Safety instruction
Follow these instructions to ensure that the product is used
correctly and to avoid danger or property loss. Serious injury or
death may occur if any of the warnings are ignored. Injury or
equipment damage may occur if any of the cautions are
neglected.
2
WARNINGS
In the use of the product, you must be in strict compliance
with the electrical safety regulations of the nation and region.
Refer to the technical specifications for detailed information.
Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or
12 VDC according to the IEC60950-1 standard. Refer to the
technical specifications for detailed information.
Do not connect several devices to one power adapter as
adapter overload may cause over-heating or fire hazard.
Make sure the plug is firmly connected to the power socket.
When the product is mounted on the wall or ceiling, the
device should be firmly fixed.
If smoke, odor, or noise rise from the device, turn off the
power at once and unplug the power cable. Contact the
service center.
If the product does not work properly, contact your dealer or
the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
3
CAUTIONS
Make sure the power supply voltage is correct before using
the camera.
Do not drop the camera or subject it to physical shock.
Do not touch CMOS modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
replace the lens cap to protect the CMOS from dirt.
Do not aim the camera at the sun or exceedingly bright
places. Blooming or smearing may occur (which is not a
malfunction), and affect the endurance of the CMOS at the
same time.
The CMOS may be burned out by a laser beam, so when
laser equipment is in use, make sure that the surface of the
CMOS will not be exposed to the laser beam.
Do not expose the camera to high electromagnetic radiation,
extremely hot or cold environments (the operating
temperature should be -30 to +60℃), or dusty or damp
locations.
To avoid heat accumulation, good ventilation is required for
operating environment.
Keep the camera away from liquid while in use.
When returning a camera, pack it in its original packing, or
similar packing materials.
Improper use or replacement of the battery may result in
hazard of explosion. Replace it with the same or equivalent
type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.
4
Overview
Figure 1: Camera Overview
(1) Sun shield
(2) Back box
(3) Grounding screw
(4) Adjustable bracket
(5) Mounting base
(6) Reset
1
2
4
6
3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Clare Controls Caméra de sécurité
Clare Controls
Clare Controls CV-P5D10-ODHIM Manuel utilisateur
Clare Controls
Clare Controls ClareVision Plus Manuel utilisateur
Clare Controls
Clare Controls CVP-B2D50-ODI Manuel utilisateur
Clare Controls
Clare Controls Mainline 2MP Manuel utilisateur
Clare Controls
Clare Controls CV-M13D10-ODI Manuel utilisateur
Clare Controls
Clare Controls ClareVision Plus Manuel utilisateur
Clare Controls
Clare Controls IP Network Camera Manuel utilisateur
Clare Controls
Clare Controls CV-P5D10-ODHIM Manuel utilisateur
Clare Controls
Clare Controls CV-M3D10-ODI Manuel utilisateur
Clare Controls
Clare Controls Mainline CV-M13B10-ODI Manuel utilisateur
Clare Controls
Clare Controls ClareVision Plus Series Manuel utilisateur
Clare Controls
Clare Controls CV-B13D10-ODI Manuel utilisateur
Clare Controls
Clare Controls ClareVision Plus Manuel utilisateur
Clare Controls
Clare Controls ClareVision Comment utiliser
Clare Controls
Clare Controls CV-M3B10-ODI Manuel utilisateur
Clare Controls
Clare Controls ClareVision Plus Manuel utilisateur
