Clare Controls CM-MT6610-BT-70 Manuel utilisateur
2015-04-917 • Rev 02
HDBaseT 6x6 Matrix Switcher
User Guide
Copyright
© 01APR15 Clare Controls, Inc. All rights reserved.
This document may not be copied in whole or in part or
otherwise reproduced without prior written consent from
Clare Controls, Inc., except where specifically permitted
under US and international copyright law.
Trademarks and
patents
HDBaseT 6x6 Matrix Switcher, part number
CM-MT6610-BT-70 name is a trademark of Clare
Controls, Inc.
Other trade names used in this document may be
trademarks or registered trademarks of the manufacturers
or vendors of the respective products.
Manufacturer
Clare Controls, Inc.
7519 Pennsylvania Ave., Suite 104
Sarasota, FL 34243, USA
Version
This document applies to HDBaseT 6x6 Matrix Switcher,
Model CM-MT6610-BT-70 Rev 01.
Contact information
For contact information, see www.clarecontrols.com.
HDBaseT 6x6 Matrix Switcher User Guide i
Content
Important information...iii
Limitation of liability...iii
Introduction...1
Features...1
Package contents...1
Front panel...2
Rear panel...3
Connecting with the RS232 communication port...4
Twisted pair cable connection...5
System connection...5
Usage precautions...5
Connecting with the HDBaseT extender set receiver...6
System diagram...7
Connection procedure...7
System applications...8
System operations...8
I/O control...8
Learn EDID data...9
EDID setting...9
Status check...10
Clear operation...10
IR control...11
IR remote...11
IR operations...12
IP and RS232 control protocol...17
Control the switcher...21
TCP/IP control...24
Control modes...24
USB firmware updating...27
ii HDBaseT 6x6 Matrix Switcher User Guide
Specifications...28
Dimensions...30
Troubleshooting and maintenance...30
Safety operation guide...31
After-sales service...32
HDBaseT 6x6 Matrix Switcher User Guide iii
Important information
Limitation of liability
To the maximum extent permitted by applicable law, in no event will Clare
Controls, Inc. be liable for any lost profits or business opportunities, loss of use,
business interruption, loss of data, or any other indirect, special, incidental, or
consequential damages under any theory of liability, whether based in contract,
tort, negligence, product liability, or otherwise. Because some jurisdictions do
not allow the exclusion or limitation of liability for consequential or incidental
damages the preceding limitation may not apply to you. In any event the total
liability of Clare Controls, Inc. shall not exceed the purchase price of the
product. The foregoing limitation will apply to the maximum extent permitted by
applicable law, regardless of whether Clare Controls, Inc. has been advised of
the possibility of such damages and regardless of whether any remedy fails of
its essential purpose.
Installation in accordance with this manual or applicable codes is mandatory.
While every precaution has been taken during the preparation of this manual to
ensure the accuracy of its contents, Clare Controls, Inc. assumes no
responsibility for errors or omissions.
iv HDBaseT 6x6 Matrix Switcher User Guide
HDBaseT 6x6 Matrix Switcher User Guide 1
Introduction
The HDBaseT 6x6 matrix switcher includes six HDMI inputs, six HDBaseT outputs,
three local HDMI outputs, and three digital coax outputs. It works with the HDBaseT
receiver to transmit HDMI, IR, and RS232. The transmission distance is 70 meters.
Features
Supports 1080P at 60 Hz and 3D
HDCP compliant, supporting HDMI 1.4a
Powerful EDID and HDCP management
Six HDBaseT outputs, to transmit HDMI, IR and RS232 to 70 meters over a
Cat6e cable or 60 meters over a Cat5e cable
Provides power for all the receivers connected to HDBaseT outputs
Supports multiple control options, including front panel, RS232, IR and TCP/IP
control (works with the Network Controller)
IR OUT signal switching follows with a video signal, which can be separated
from video switching
Multiple EDID management
LCD indicator shows connection status, switching status, HDCP status, and
output resolution
Package contents
1 x HDBaseT 6x6 matrix switcher
2 x Mounting ears (6 x screws)
1 x Power cord
1 x RS232 cable
4 x Plastic cushions (4 x screws)
1 x IR remote
18 x Terminal blocks
1 x User manual
6 x IR converting cables
6 x IR emitters
2 HDBaseT 6x6 Matrix Switcher User Guide
Front panel
Figure 1: Front panel
(1) Firmware
Micro USB port for updating firmware.
(2) Power indicator
Power 'on' indicator light.
(3) IR receiver
IR receive window.
(4) LCD indicator
Shows real-time system status.
(5) INPUTS
Normal mode: The input buttons range from 1 to 6.
Inquire mode: Press and hold SELECT for three seconds to
enter this mode. Press ◄► to change menus and ▲▼ to
change channels.
(6) OUTPUTS
Output buttons range from 1 to 6. HDMI INPUT 1 to 3 support
local HDMI output.
(7) FUNCTION
GLOBAL: Select all outputs to transfer on input to all outputs.
Example: Transfer both AV and IR signals from input channel 1
to all output channels.
Operation: Press 1 + GLOBAL + SELECT.
EDID: Management button. Enable the input port to manually
capture and study the EDID data of output devices.
Example: Input channel 2 captures and studies the EDID data of
output channel 4.
Operation: Press buttons in this order EDID + 2 + 4 + SELECT.
Note: Press button 2 in INPUTS and 4 in OUTPUTS.
CLEAR: Clear an operation, such as switching output channel,
studying EDID data before it comes into effect. Meanwhile, the
switcher returns to the previous state.
SELECT: Confirm operation. Press and hold it for three seconds
to enter the Inquire mode.
HDBaseT 6x6 Matrix Switcher User Guide 3
Rear panel
Figure 2: Rear panel
(1) INPUTS
a. IR OUT: Connect with IR transmitter, six in total, to send out the IR
signal from the HDBaseT port of the far-end receiver. These IR OUTs
make up an IR switcher with the IR INs on the HDBaseT receivers, and
all can be switched synchronously with the AV signal, or separately
switching.
b. HDMI: HDMI input ports, six in total, type A female HDMI
connector,
connect with HDMI input source devices.
(2) OUTPUTS
c. IR IN: Connect with IR receiver, fixed IR input for the output, cannot
be switched separately. It makes up an IR bi-directional transmission
with the IR OUT on the corresponding HDBaseT receiver.
d. RS232: RS232 port to communicate with the RS232 port
on
corresponding HDBaseT receiver. When controlled by HDBaseT
receiver, the communication protocol must be the same with the
switcher.
e. AUDIO: stereo analog output ports, six in total.
f. HDMI: HDMI output port, for HDMI inputs 1 to 3. To split HDMI output
for local monitoring or used instead of HDBaseT outputs.
g. HDBaseT: Works with receivers using HDBaseT
technology, such as
the HDMI CAT5 cable receiver and the HDMI POH (Power Over
HDBaseT) twisted pair receiver. It can pass through AV,
IR, and RS232
signals up to 70 meters.
(d) (e)
(f)
(g)
(3)
(4)
(5)
(7)
(8)
(1) (2) (6) (9)
(a) (c)
IR IN
1
OUTPUT1
HDMI
HDBaseT
RS232 AUDIO
TX RX
L R
IR IN
2
OUTPUT2
HDMI
HDBaseT
RS232 AUDIO
TX RX
L R
IR IN
3
OUTPUT3
HDMI
HDBaseT
RS232 AUDIO
TX RX
L R
IR IN
4
OUTPUT4
HDBaseT
RS232 AUDIO
TX RX
L R
5
OUTPUT5
HDBaseT
RS232
TX RX
IR IN
AUDIO
L R
IR IN
6
OUTPUT6
HDBaseT
RS232 AUDIO
TX RX
L R
RS232
IR ALL IN
TCP/IP
IR EYE
12
INPUT
HDMI 1HDMI 2
12
INPUT
HDMI 1
HDMI 2
IR OUT
12
INPUT
HDMI 1HDMI 2
IR OUT
4 HDBaseT 6x6 Matrix Switcher User Guide
(3) RS232
The serial port for unit control, 9-pin female connector, needs a straight
through cable and connects with control devices, such as a PC.
(4) IR ALL IN
IR control signal input port, connect with IR receiver, pass through all
the HDBaseT ports (regardless of the selected input/output) to control
remote devices.
(5) TCP/IP
RJ45 port for unit control.
(6) IR EYE
Connects with the extended IR receiver. Used to extend the IR control of
the switcher functions.
(7) Power
Press the button to power the switcher. The indicator turns red and
remains on when the power is on.
(8) Power supply
Connects with 110 to 240 VAC power adapter.
(9) GROUND
Connects to ground.
Connecting with the RS232 communication port
You can control the switcher from the front panel, IR, or RS232. RS232 control is
used via the rear RS232 communication port. It is a female 9-pin D connector. The
pin definitions are listed in the table below.
Table 1: RS232 connection definitions
No.
Pin
Function
1
N/u
Unused
2
Tx
Transmit
3
Rx
Receive
4
N/u
Unused
5
Gnd
Ground
6
N/u
Unused
7
N/u
Unused
8
N/u
Unused
9
N/u
Unused
Table des matières
Autres manuels Clare Controls Commutateur matriciel
Clare Controls
Clare Controls HDBaseT 16x16 Manuel utilisateur
Clare Controls
Clare Controls CM-MT8810-BT-70 Manuel utilisateur
Clare Controls
Clare Controls CM-MT4420-HD Manuel utilisateur
Clare Controls
Clare Controls CM-MT4410-BT-70 Manuel utilisateur
Clare Controls
Clare Controls CM-MT8810-HD Manuel utilisateur
