Cisco ATA 191 Fiche technique

Get Started with Your New ATA

•Your New ATA, on page 1

•Devices Associated with Your ATA, on page 4

•Install Your New ATA, on page 4

•Mount Your ATA, on page 6

•Supported ATA Call Features, on page 7

Your New ATA

Your analog telephone adapter (ATA) allows you to connect an analog device, such as an analog phone or

fax machine, to your network. The connected device can then function like the IP phones in your network.

Your new analog telephone adapter (ATA) has two interfaces:

• Two RJ11 ports for analog devices

• A RJ45 port for Ethernet

Light-emitting diodes (LEDs) on the ATA provide status.

You'll perform these tasks:

• Install your ATA with the components in the box.

Cisco ATA 191 Hardware

The ATA 191 and ATA 192 are compact, easy to install devices.

The unit provides these connectors:

• 5V DC power connector.

• Two RJ-11 FXS (Foreign Exchange Station) ports—Your ATA has two RJ-11 ports that work with any

standard analog phone device. Each port supports either voice calls or fax sessions, and both ports can

be used simultaneously.

• One WAN network port—An RJ-45 10/100BASE-T data port to connect an Ethernet-capable device to

the network.

Get Started with Your New ATA

The ATA network port performs autonegotiation for duplex and speed. It supports speeds of 10/100 Mbps

and full-duplex.

Note

ATA 191 Top Panel

The top panel of your ATA has several LEDs that are used to show the device's status.

Figure 1: ATA 191 Top Panel

The following table describes the LEDs located on your ATA.

Table 1: ATA 191 Top Panel Items

DescriptionItem

Steady green: System booted up successfully and is ready for use.

Slow flashing green: System is booting up.

Fast flashing green three times, then repeats: System failed to boot

up.

Off: Power is off.

Power LED

Flashing green: Data transmission or reception is in progress through

the WAN port.

Off: No link.

Network LED

Steady green: On hook.

Slow flashing green: Off hook.

Fast flashing green three times, then repeats: The analog device failed

to register.

Off: The port is not configured.

Phone 1 LED

Phone 2 LED

Get Started with Your New ATA

ATA 191 Top Panel

DescriptionItem

Press this button to create a problem report using the Problem Report

Tool.

This is not a power button. When you press this button, a

problem report is generated and uploaded to a server for the

system administrator.

Note

Problem Report Tool (PRT) Button

Flashing amber: The PRT is preparing the data for the problem report.

Fast Flashing amber: The PRT is sending the problem report log to

the PRT server.

Solid green for five seconds, then off: The PRT report was sent

successfully.

Flashing red: The PRT report failed. Press the PRT button to turn the

LED off. Once it is off, another press triggers a new PRT report.

Problem Report Tool (PRT) LED

ATA 191 Back Panel

The back panel of your ATA has several ports used to connect your device and to power it. The back panel

also has the reset button for resetting the device to the factory settings.

Figure 2: ATA 191 Back Panel

The following table describes the ports that are located on the back panel of your ATA.

Table 2: ATA 191 Back Panel Ports

DescriptionPort or Button

To restart the ATA, use a paper clip or similar object to press this button

briefly.

To restore the factory default settings, press and hold for 10 seconds.

RESET

Use an RJ-11 phone cable to connect an analog phone or fax machine.PHONE 1

Use an RJ-11 phone cable to connect a second analog phone or fax

machine.

PHONE 2

Use an Ethernet cable to connect to the network.NETWORK

Use the provided power adapter to connect to a power source.DC 5V POWER

Get Started with Your New ATA

ATA 191 Back Panel

Devices Associated with Your ATA

Use your ATA to connect these types of devices to your network:

• Analog phones

• Analog phones have no softkeys.

• The information that analog phones display depends on the model you have.

• You use the phone’s flash button for hold, resume, transfer, and conference.

• Analog telephony voice devices

• The ATA supports analog telephony voice devices, such as overhead paging adapters and answering

machines, that emulate a regular phone.

• Overhead paging systems

• Overhead paging systems provide alarms and public-address announcements in buildings.

• Fax machines

• Use a fax machine directly with an ATA. Don’t connect an extension to a fax machine, and don’t

use the fax machine with a splitter.

• To reduce fax failures, use overseas mode, if available; if not, set the fax machine transmission

speed to low.

• Data devices, such as facsimile machines and modems, may not function optimally. For the best

fax and modem performance, continue to use a dedicated PSTN line.

Install Your New ATA

Your ATA comes with everything to power it up, connect it to the network, and set it up on your desk.

Before you begin

Before you begin the installation, make sure you have the following equipment:

• Ethernet cable to connect to your network.

• Analog phone or fax machine to connect to your ATA.

• Phone cable to connect your phone.

• Uninterruptible power supply (UPS) to provide backup power.

Procedure

Step 1 Connect the network cable to your network and to the NETWORK port on the ATA.

Get Started with Your New ATA

Devices Associated with Your ATA

Step 2 Connect the phone cable to the PHONE 1 port on the ATA and to your analog device (phone or fax machine).

If connecting a fax machine, connect it directly to the ATA. Do not connect an extension to a fax machine,

and do not use a splitter.

Step 3 (Optional) If you have a second analog device, connect the phone cable to the PHONE 2 port on the ATA

and to your second analog device.

Step 4 Connect the ATA power cable to the DC 5V POWER port on the ATA, and plug the power cable into your

power source.

Get Started with Your New ATA

Install Your New ATA

Mount Your ATA

You can place the ATA on a desktop or mount it on a wall.

To prevent the ATA from overheating, do not operate it in an area that exceeds an ambient temperature of

104°F (40°C).

Caution

Desktop Placement

Place the ATA on a flat surface near an electrical outlet.

Do not place anything on top of the ATA; excessive weight could damage it.

Warning

Wall Mounting

The ATA has two wall-mounted slots on the bottom panel. To mount the ATA on a wall, you need mounting

hardware (not included). Suggested hardware is illustrated (not true to scale).

Recommended hardware (not included): Two #6 pan head, 5/8 in., self-tapping screws with anchors for

sheet rock installation.

Get Started with Your New ATA

Mount Your ATA

Insecure mounting might damage the ATA or cause injury. Cisco is not responsible for damages incurred

byinsecure wall-mounting.

Note

Procedure

Step 1 Determine where you want to mount the unit. Verify that the surface is smooth, flat and dry.

Step 2 Drill two pilot holes into the surface 58 mm apart (about 2.28 in.).

Step 3 Insert a screw into each hole, leaving a gap of 5 mm (0.1968 in.) between the underside of each screw head

and the surface of the wall.

Step 4 Place the unit wall-mount slots over the screws and slide the unit down until the screws fit snugly into the

wall-mount slots.

Supported ATA Call Features

Depending on your system configuration, your ATA supports some or all the following call features:

Get Started with Your New ATA

Supported ATA Call Features

• Transfer (attended or supervised)—In this type of transfer, you talk to the receiving party before you

complete the transfer.

• Transfer (unattended or unsupervised)—In this type of transfer, you complete the transfer and hang up

before the receiving party answers.

• Conference.

• Hold and Resume.

• Caller ID.

• Call Waiting.

• Call Pickup.

• Speed Dial.

• Music On Hold.

• Shared Lines.

• Voicemail—This feature has no visual indicator, but a message waiting tone when you go off-hook

indicates that you have voice messages. Some analog phones with a large LCD screen may display a

voicemail icon.

• Call Forward.

• Redial.

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur