CIMCO OXE Series Manuel utilisateur
1
OXE DIESEL SINGLE CONTROL HEAD MANUAL
CONTROL HEAD SINGLE MANUAL
Publication No: ODM1014
DIESEL ENGINE
3
OXE DIESEL SINGLE CONTROL HEAD MANUAL
CONTENT
CONTENTS
Overview_______________________________________________________________________________ 4
About this manual ______________________________________________________________________ 4
Safety information _______________________________________________________________________ 5
Notice to the operator____________________________________________________________________ 5
Safety regulations _______________________________________________________________________ 6
Prior to every use _______________________________________________________________________ 6
During use_____________________________________________________________________________ 7
Aer use ______________________________________________________________________________ 7
Maintenance ___________________________________________________________________________ 7
Safety labels____________________________________________________________________________ 8
Components labels______________________________________________________________________ 8
Other labels____________________________________________________________________________ 8
Description _____________________________________________________________________________ 9
General _______________________________________________________________________________ 9
NMEA 2000® Network ___________________________________________________________________ 9
Control Head ___________________________________________________________________________ 9
Control head overview __________________________________________________________________ 10
Operation _____________________________________________________________________________ 11
Before each use ________________________________________________________________________ 11
First time use _________________________________________________________________________ 11
Single lever control head ________________________________________________________________ 12
Control head operation __________________________________________________________________ 13
Neutral throttle warmup ________________________________________________________________ 15
Low speed control _____________________________________________________________________ 16
Trolling mode _________________________________________________________________________ 16
Lever adjustment ______________________________________________________________________ 17
Station selection and station select protection _______________________________________________ 18
Faults and hazards______________________________________________________________________ 19
Maintenance___________________________________________________________________________ 20
User’s responsibility ____________________________________________________________________ 20
Qualified OXE Diesel Mechanic ____________________________________________________________ 20
Mounting template______________________________________________________________________ 21
4
OXE DIESEL SINGLE CONTROL HEAD MANUAL
OVERVIEW
OVERVIEW
ABOUT THIS MANUAL
This manual provides you with the information you need to know about safely
operating and maintaining your OXE Diesel Control Head. It should be stored on
the boat.
Specifications, operating and maintaining descriptions are subject to change
without notice.
Cimco Marine AB
Metallgatan 17B
SE-262 72 Ängelholm, Sweden
+46 (0)431-371130
5
OXE DIESEL SINGLE CONTROL HEAD MANUAL
SAFETY INFORMATION
NOTICE TO THE OPERATOR
Throughout this publication, Dangers, Warnings and Cautions (accompanied by
the International Hazard Symbol) are used to alert the user to special instructions
concerning a particular service or operation that may be hazardous if ignored or
performed incorrectly or carelessly. Study them carefully!
These safety alerts alone cannot eliminate the hazards that they signal. Strict
compliance with these special instructions during installation, operation, and
maintenance, as well as common sense operation, are important measures to
prevent accidents.
Failure to adhere to these notices may result in the loss of steering and shi/
throttle control, leading to possible ejection from the boat, causing property
damage, injury and/or death.
Symbols and signs
!DANGER
This indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
!WARNING
This indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
!CAUTION
This indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTE! Important information.
SAFETY INFORMATION
6
OXE DIESEL SINGLE CONTROL HEAD MANUAL
SAFETY REGULATIONS
SAFETY REGULATIONS
!WARNING
The safety information provided below is intended to inform you of the
dangers that may be present before, during and aer use. It is critical that
you read and understand all the points noted.
!WARNING
The OXE Diesel Control Head system must only be installed by an authorized
dealer or OEM.
Safe operation of the shi and throttle system depends upon proper installation
and maintenance of the system, and common sense, safe judgment, knowledge,
and expertise of the operator. Every installer and operator of the shi and throttle
system should know the following requirements before installing or operating the
system.
If you have any questions regarding any of these warnings, contact your OXE
Diesel retailer.
To reduce the risk of severe injury or death:
1. Always wear a Coast Guard-approved personal flotation device (PFD) and
use an engine shut-off cord (lanyard).
2. Read and understand this manual and the Quick Reference Card provided
with your boat control components.
3. OXE Diesel components are highly engineered and safety tested to ensure
system integrity. DO NOT substitute any component. Substitution with
non-OXE components may compromise system safety, performance, and
reliability.
PRIOR TO EVERY USE
Perform a system inspection as outlined below. See section Operation for further
details.
1. Check your boat’s steering system for proper operation.
2. Inspect all electrical cables for wear, kinks, or leaks.
3. Check for binding, loose or worn shi/throttle control components.
4. Verify proper shi and throttle response for all control levers.
!WARNING
Do not operate boat if any components is not in proper working condition.
7
OXE DIESEL SINGLE CONTROL HEAD MANUAL
DURING USE
1. Wear an, according to local legislation, approved life jacket.
2. Attach engine shut-off cord (lanyard) to your PFD.
3. Never allow anyone not familiar with the operation of the boat control
system to operate the boat at ANY time.
4. Know and adhere to all applicable federal, state, and municipal laws and
regulations that govern boating in your area.
!WARNING
Do not operate the boat if any components are not in proper working
condition.
AFTER USE
No special care is required aer using the control head system. Periodically clean
the control head with a damp cloth and a mild detergent, if necessary.
MAINTENANCE
Maintain your control head system as directed in section Maintenance of this
manual.
SAFETY REGULATIONS
8
OXE DIESEL SINGLE CONTROL HEAD MANUAL
SAFETY LABELS
!WARNING
The labels below should call attention to the possible hazards associated with the equipment shown
later in this manual.
COMPONENTS LABELS
Figure 1-1. Start-In-Gear Advisory Decal, PID#682050.
Figure 1-2. A and B Locator Decal, PID# 682049.
OTHER LABELS
Figure 1-4. Ignition warning decal, PID# 682300.
SAFETY LABELS
9
OXE DIESEL SINGLE CONTROL HEAD MANUAL
DESCRIPTION
GENERAL
The OXE diesel Control Head replaces a traditional cable-operated engine remote
control with an electronic control.
The elimination of mechanical cables to the control head simplifies multi-station
installations, especially when a station is installed onto a flybridge or tower that
is removed for shipping. The system supports the installation of up to two control
heads.
When installing the OXE diesel Control Head, it is recommended to have access to
the OXE diesel Installation Manual.
NMEA 2000® NETWORK
The NMEA 2000® is a CAN based serial network protocol widely used in marine
control systems.
The NMEA 2000® bus contains a backbone connecting all devices, two
terminators, one at each backbone, that reduces interference and dropouts to
each device.
CONTROL HEAD
The OXE Diesel Control Head communicates via the NMEA 2000® bus to the
engine and features status lights, a synchronous trim switch (optional), and
control buttons for additional functions.
DESCRIPTION
10
OXE DIESEL SINGLE CONTROL HEAD MANUAL
DESCRIPTION
CONTROL HEAD OVERVIEW
DUAL STATION/DUAL ENGINE SINGLE STATION/SINGLE ENGINE
1
1
3
3
2
2
1
1
1
3
3
2
2
1
1. Control Head
2. NMEA 2000® helm connectors
3. NMEA 2000® Bus
Ce manuel convient aux modèles suivants
2
Table des matières
