Christie One Manuel utilisateur
Assembling the Christie
One rigging frame
With the Christie One rigging frame, the projector can be secured to trusses or structures built for the
purpose of positioning the projector.
With the frame:
• Up to three projectors can be stacked in landscape orientation.
• A single projector can be positioned in portrait mode but no stacking is permitted.
Christie ships the frame separately from the projector.
Affected products
The Christie One rigging frame is designed for use with the following projectors.
• HS Series projectors (D13HD-HS, D13WU-HS, D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU-
HS, D20HD-HS, D20WU-HS, DWU1612-HS, DWU2022-HS)
• H Series (D12HD-H and D12WU-H)
• Q Series (DWU951-Q, DHD951-Q, DWX951-Q, DXG1051-Q, DWU851-Q, DHD851-Q, DWX851-
Q)
• GS Series (DHD635-GS, DWU635-GS, DHD635-GS China, DWU635-GS China, DHD630-GS,
DWU630-GS, DHD630-GS China Black, DWU630-GS China, DHD630-GS Black, DWU630 GS
Black, DHD1075-GS, DWU1075-GS, DHD1075-GS China, DWU1075-GS China, DWU6322-GS,
DWU7062-GS, DWU1082-GS, DHD850-GS, DWU850-GS, DHD700-GS, DWU700-GS)
Required components
The following components are required.
Christie One rigging frame (P/N: 140-113106-03 or higher)
Safety warnings and guidelines
Read all safety and warning guidelines before starting this procedure.
Danger! If not avoided, the following results in death or serious injury.
• Do not stack the device unless specified in this manual.
• The supporting structure must safely support the combined load of the product, all attached
hardware, and components following all local safety standards and regulations.
• Use all mounting points, including the safety point, when installing the product overhead.
Assembling the Christie One Frame Instruction Sheet 1
020-101901-04 Rev. 1 (03-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Warning! If not avoided, the following could result in death or serious injury.
• Only use this frame with the specified products.
• Safety straps must be used when stacking two or more rigging frames.
• Always install safety straps when the frame and projector are installed overhead.
• Do not stack empty frames.
• Projectors must be installed in frames before stacking.
Notice. If not avoided, the following could result in property damage.
• Use appropriate packaging when shipping the product installed in the frame.
Tools required
The following tools are required for installing the rigging frame.
• 3 mm hex key (Christie One rigging frame)
• 4 mm hex key (Christie One rigging frame)
• 5 mm hex key (Q Series, GS Series)
• 6 mm hex key (H Series, HS Series)
Optional tools
• Adjustment tool provided with the Christie One rigging frame
Physical specifications
Learn the weight and physical dimensions of the Christie One rigging frame.
• Weight: 40.37 kg (89 lbs)
• Dimensions: 790 mm x 790 mm x 483 mm
Assembling the Christie One rigging frame
Assembling the Christie One Frame Instruction Sheet 2
020-101901-04 Rev. 1 (03-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Securing the projector to the stacking frame
Secure the projector to the stacking frame before stacking additional projectors.
Danger! If not avoided, the following results in death or serious injury.
• TIP HAZARD! Stacked frames must be secured together using all locking pins.
• Use all mounting points, including the safety point, when installing the product overhead.
Warning! If not avoided, the following could result in death or serious injury.
• A minimum of four people or appropriately rated lift equipment is required to safely lift, install,
or move the product.
• The supporting structure must safely support the combined load of the product, all attached
hardware, and components following all local safety standards and regulations.
1. Turn off the projector.
Allow the cooling fans to stop before proceeding with step 2.
2. Disconnect the projector from AC power.
3. Remove lens from projector, if installed.
4. Verify the base plate of the frame is in a flat position and is level.
5. Adjust the feet of the projector.
• For HS Series, Q Series, and GS Series, adjust the feet of the projector so there is no
extension.
• For H Series, extend the projector feet out 4 mm before placing in the frame.
The projector must sit flat on the base plate.
6. Place the four spacers provided with the frame over the four appropriate mounting holes on
top of the base/mounting plate.
•For HS Series, place the four spacer provided with the frame over the four HS Series
mounting holes on top of the base plate.
• For GS Series 630/635, DWU6322-GS, and DWU7062-GS only, place the four spacers
provided with the frame over the four orange GS Series mounting holes on top of the
mounting plate.
Ensure the holes on the base plate and spacers are aligned.
7. Lift the projector onto the base plate through the top opening of the frame.
Ensure the lens mount faces the front of the frame, as indicated below.
Assembling the Christie One rigging frame
Assembling the Christie One Frame Instruction Sheet 3
020-101901-04 Rev. 1 (03-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
8. Secure the projector to the base plate using four hex socket head screws and washers
provided with frame.
• For H Series and HS series projectors, use M8 x 1.25 x 40 mm bolts and washers and
secure with a 6 mm hex key.
The M8 bolts must be tightened to a torque of 38 Nm.
• For GS Series 630/635 GS Series, DWU6322-GS, and DWU7062-GS projectors, use M6 x
1.0 x 35 mm bolts and washers.
The M6 bolts must be tightened to a torque of 16 Nm.
• For GS Series 1075, GS Series 850/700, DWU1082-GS, and DWU8902-GS projectors, use
M6 x 1.0 x40 bolts and washers.
The M6 bolts must be tightened to a torque of 16 Nm.
• For Q Series projectors, use M6 x 1.0 x 16 mm bolts and washers and secure with a 5 mm
hex key.
The M6 bolts must be tightened to a torque of 16 Nm.
The Q Series, GS Series 850/700, GS Series 1075, DWU1082-GS, and DWU8902-GS
hardware includes optional adhesive washers than can be used between the frame
mounting plate and the projector to help align the projector for installation.
Refer to the image below for the mounting points on the base plate for each projector series.
Assembling the Christie One rigging frame
Assembling the Christie One Frame Instruction Sheet 4
020-101901-04 Rev. 1 (03-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
• Purple—H and HS series screws M8 x 1.25 x 40 mm bolts and washers
•Green—Q series screws M6 x 1.0 x 16 mm bolts and 3 mm thick adhesive washers
• Orange—GS Series 630-GS/635, DWU6322-GS, and DWU7062-GS screws M6 x 1.0 x 35
mm and washers for M6
• Red—GS Series 1075, GS Series 850-GS/700 Series, DWU8902-GS, and DWU1082-GS
screws M6 x 1.0 x 40 mm and 3 mm thick adhesive washers for M6
Stacking multiple framed projectors
Up to three framed projectors can be stacked in landscape orientation only, and then rigged in an
upright or inverted position. Stacking in portrait orientation is not permitted.
Danger! If not avoided, the following results in death or serious injury.
• TIP HAZARD! Stacked frames must be secured together using all locking pins.
• Do not stack the device unless specified in this manual.
Assembling the Christie One rigging frame
Assembling the Christie One Frame Instruction Sheet 5
020-101901-04 Rev. 1 (03-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Warning! If not avoided, the following could result in death or serious injury.
• A minimum of four people or appropriately rated lift equipment is required to safely lift, install,
or move the product.
• The supporting structure must safely support the combined load of the product, all attached
hardware, and components following all local safety standards and regulations.
• Do not stack empty frames.
• Projectors must be installed in frames before stacking.
1. Remove the locking pins from each stacking leg.
2. With one person positioned on each side of the framed projector, lift the assembly and place it
onto the bottom frame.
Stacking in portrait orientation is not permitted
3. Verify the four stacking legs of the upper assembly are securely seated on the bottom frame.
4. Insert a locking pin through each of the stacking legs to lock the frames together.
The steel ball on the end of the pin keeps the pin from releasing inadvertently.
5. Install safety straps (not included) between the frames.
Safety straps must be adequately rates for the total load.
6. When stacking a third framed projector, repeat steps 1 to 4.
Assembling the Christie One rigging frame
Assembling the Christie One Frame Instruction Sheet 6
020-101901-04 Rev. 1 (03-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Aligning stacked projectors
Stacked projectors must be correctly aligned to one another to achieve an optimally displayed image.
1. Hoist and secure a stack of projectors before aligning.
2. Loosen the locking screws on each adjustment knob.
3. Before adjusting the roll, loosen the four screws on the base plate; otherwise, the adjustment
knob can break during adjustment.
4. Adjust pitch, roll, or yaw, manually or with the optional adjustment tool provided with the
frame, until the image geometry is optimized.
a) To adjust the roll of the display clockwise, rotate the adjustment pin clockwise and vice-
versa.
b) To adjust the pitch of the projector, loosen the two locking rings on the top and bottom of
the adjustment screw. To tilt the image down, turn the adjustment screw to the right. To
tilt the image up, turn the adjustment screw in the opposing direction.
If having trouble adjusting the adjustment screw, use a 4 mm hex key and place it in one
of the holes on the adjustment screw, then turn in required direction. Once the image is
properly adjusted, tighten the two locking rings.
c) To adjust the yaw of the projector, loosen the four adjustment knobs with a 6 mm hex key
and make adjustments. Once properly adjusted, re-tighten the four adjustment knobs.
A Roll—Rotates the image clockwise or counter-clockwise.
B Pitch—Moves the image up and down.
C Yaw—Moves the image to the left or right.
5. For pitch and yaw, ensure the gap between the pin and the plate is more than 0.5 mm.
The pin limits the adjustment within the useful range.
6. To lock adjustments, tighten the setscrews with a 3 mm hex key on each adjustment knob.
Assembling the Christie One rigging frame
Assembling the Christie One Frame Instruction Sheet 7
020-101901-04 Rev. 1 (03-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Christie Accessoires pour projecteur
Christie
Christie LX380 Manuel utilisateur
Christie
Christie Brio Team+ Manuel utilisateur
Christie
Christie Brio Manuel utilisateur
Christie
Christie QwikRig rigging frame Manuel utilisateur
Christie
Christie 118-131106 Series Manuel utilisateur
Christie
Christie P100 Manuel utilisateur
Christie
Christie IMB-S3 Manuel utilisateur
Christie
Christie QwikRig Rigging Frame V2 Manuel de programmation
Christie
Christie CoreIII Series Instructions de montage
Christie
Christie RPMWU-RPMSP-LED01 Manuel utilisateur
Christie
Christie LX32 Mode d’emploi
Christie
Christie Christie One Mount Mode d’emploi
Christie
Christie 163-126100 Series Manuel utilisateur
Christie
Christie CIC Instructions de montage
Christie
Christie 104-006101-XX Manuel utilisateur
Christie
Christie ChristieNet Wireless Presentation Portal Manuel utilisateur
Christie
Christie Vivid Blue 38-VIV301-01 Manuel utilisateur
Christie
Christie Brio Manuel utilisateur
Christie
Christie Brio Enterprise Manuel utilisateur
Christie
Christie 003-006191-01 Manuel utilisateur
