CHERUBINI A510078 Manuel utilisateur

DRAFT

ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN

INSTRUCTIONS - INSTRUCCIONES

Actuator for motors with

standard connection EN

A510078 META

WIRED MOTOR CONTROLLER 7

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Index:

Device description ................................................................................................. p. 4

Technical specications.......................................................................................... p. 5

Safety information ................................................................................................. p. 5

Electrical connections diagram .............................................................................. p. 6

Device installation.................................................................................................. p. 7

LED status indicator ............................................................................................... p. 7

Add/remove the device into a Z-WaveTM network (classic)..................................... p. 8

SmartStart inclusion............................................................................................... p. 9

S2 Secure Inclusion ................................................................................................ p. 9

Supported command classes ............................................................................ p. 10-11

Device control ........................................................................................................ p. 12

Controlling the device by External Switches ....................................................... p. 12

Controlling the device by a Z-WaveTM controller ................................................. p. 13

Reset to the factory settings .................................................................................. p. 14

Firmware update.................................................................................................... p. 14

Ofine setup mode ................................................................................................ p. 15

Congurations ................................................................................................. p. 16-20

EU declaration of conformity

CHERUBINI S.p.A. declares that the product is in conformity with the relevant Union

harmonisation legislation: Directive 2014/53/EU, Directive 2011/65/EU.

The full text of the EU declaration of conformity is available upon request at the following

website: www.cherubini.it.

Failure to comply with these instructions annuls CHERUBINI’s responsibilities and

guarantee.

The crossed-out wheelie bin symbol indicates that the product must be collected

separately from other waste at the end of its useful life. Therefore, users should

deliver this product to appropriate waste collection points or return it to their

dealers at the end of its service life. See your local authority’s regulations.

Adequate waste sorting for subsequent processing and environmentally compatible

disposal helps to avoid possible negative effects on the environment and public health

and promotes reuse and/or recycling of the materials used to make the equipment.

ENGLISH

META Wired Motor Controller 7 is an “in wall device”, for the multilevel control of

roller shutter motors. It can accurately control the opening and closing of blinds,

curtains, shutters, venetian blinds as requested by the user through local commands

or remotely using computers, smartphones, tablets. At the same time, it is completely

congurable so that it can adapt to the most varied customers’ needs, while being

ready for use without needing additional congurations in order to operate. After

an initial calibration procedure, thanks to a proprietary algorithm, the device is able

to identify the exact position of the roller shutter without using external sensors.

During the operation, a continuous and automatic control of the limit switches allows

maintaining the calibration. In the absence of a power source, the system runs a self-

repositioning procedure that restores calibration. The device is equipped with contact

protection technology (Zero Crossing) which reduces the electrical stress on the relay

contacts and ensures a longer life. The open / closed switching of the device always

occur when the instantaneous value of voltage is 0. It operates in any Z-Wave™

network with other Z-Wave™/Z-Wave Plus™ certied devices and controllers from

any other manufacturer. As a constantly powered node, the device will act as repeater

regardless of the vendor in order to increase the reliability of the network. This device

is a security enabled Z-Wave Plus™ product that is able to use encrypted Z-Wave

Plus™ messages to communicate to other security enabled Z-Wave Plus™ products.

This device must be used in conjunction with a Security Enabled Z-Wave™ Controller

in order to fully utilize all implemented functions.

Integrated Button 1 or 3 clicks to enter in Learn Mode

6 clicks to reset the system to manufacturer’s settings

2 clicks to enter in setup mode

Power Supply 1 – Null

6 – Line

Open/Close Buttons

2, 3

Motor Contacts 4, 5

DEVICE DESCRIPTION

Integrated Button

with LED indicator

ENGLISH

TECHNICAL SPECIFICATIONS

SAFETY INFORMATION

Power supply 110 - 230 VAC ± 10% 50/60 Hz

Maximum Load 1200 Watt

System temperature limitation 105 °C

Work temperature From -10° to 40° C

Power consumption < 230 mW in standby mode

< 500 mW when motor is moving

Radio frequency 868.4 MHz

Protection system S2 Security

Maximum distance Up to 100 m outdoor

Up to 40 m indoor

Dimensions 37x37x17 mm

Actuator element Relay

Compliance CE, RoHs

Electrical IP Rating IP20

INFO: The device is designed to be installed in ush mounting junction boxes or

close to the motor to be controlled.

WARNING: The device must be installed by electricians qualied to intervene

on electrical systems in compliance with safety requirements set out by the

regulations in force.

DANGER: The device must be connected with a voltage of 230 VAC, before

carrying out any operation, please make sure the power main switch is in OFF

position.

DANGER: Any procedure requiring the use of the Integrated Button is related

only to the installation phase and is to be considered a service procedure that

must be performed by qualied personnel. This operation must be performed

with all necessary precautions for operating in areas with a single level of

insulation.

WARNING: Do not connect loads that exceed the maximum load permitted by

the actuator element.

WARNING: All connections must be performed according to the electrical

diagrams provided.

WARNING: The device must be installed in norm-compliant systems suitably

protected from overloads and short circuits.

ENGLISH

The device must be supplied by 230 AC Power Supply.

Connections must be done following one of the diagrams below:

ELECTRICAL CONNECTIONS DIAGRAM

WARNING: The power line must be opportunely protected from short-circuits

and excess load due to a potential motor malfunction.

Power Supply 1 – Null

6 – Line

Commands Switch 2, 3

Motor terminals 4, 5

ENGLISH

1 2 3 4 5 6

1) Neutral; 6) Phase; 4, 5) Motor terminals; 2, 3) Commands switch

1) Make sure the main switch is set to the OFF position

2) Connect the device based on the diagrams provided

3) Turn the main switch to the ON position

4) If necessary, calibrate the motor limit switches (see motor manufacturer’s manual)

5) Include the device in the Z-WaveTM network

DEVICE INSTALLATION

LED STATUS INDICATOR

TIP: The antenna must not be shortened, removed or

modied. To ensure maximum efciency, it must be

installed as shown. Large size metal equipment near the

antenna can negatively affect reception. Each device is a node

in a mesh network. If there are metal obstacles, the obstacle

can often be overcome with a further triangulation node.

The system includes an RGB LED that shows the device’s status during installation:

Solid RED: the device is not included in any network

Solid BLUE: the device is Ofine setup mode

Blink BLUE: calibration

4 GREEN blinks then OFF: the device has been just added to a Z-WaveTM network in

S2 Authenticate Mode

4 BLUE blinks then OFF: the device has been just added to a Z-WaveTM network in S2

Unauthenticated Mode

4 RED blinks then OFF: the device has been just added to a Z-WaveTM network without

security

Sequence of GREEN-BLUE Learn Mode for inclusion

Sequence of RED-BLUE Learn Mode for exclusion

Rapid sequence of GREEN-BLUE-RED: the event on the input (external switch) is not

valid.

TIP: To test if the electrical connections are correct, before the inclusion of the

device, while pressing ntimes the external switch, the RGB LED should ash

green for the same amount of times. If it does not, check the wire connections.

ENGLISH

ADD/REMOVE THE DEVICE INTO A Z-WAVETM NETWORK

(classic)

Standard Inclusion (add)

All META Serie 7 devices are compatible with all Z-WaveTM/Z-Wave PlusTM certied

controllers. The devices support both the

Network Wide Inclusion

mechanism (which

offers the ability to be included in a network, even if the device is not directly connected

to the controller) and

Normal Inclusion

By default, the inclusion procedure starts in

Normal Inclusion

mode and after a short

timeout the procedure continues in

Network Wide Inclusion

mode that lasts for about

20 Seconds.

Only a controller can add the device into the network. After activating the inclusion

function by the controller, the device can be added by setting it in

Learn Mode

Before including the device, the LED status indicator is solid RED. The adding of a

device is executed by activating the adding procedure in the inclusion section of the

controller interface and then executing 1 or 3 click on the integrated button (the device

is set in

Learn Mode

). As soon as the inclusion procedure initiates the LED indicator

starts a sequence of GREEN-BLUE blinks. The device is included in the network when

the LED status is OFF and the interview is completed.

Standard exclusion (remove)

Only a controller can remove the device from the network. After activating the exclusion

function by the controller, the device can be removed by setting it in

Learn Mode

The procedure of exclusion can be activated by Removing a node from the Z-WaveTM

network and executing 1 or 3 click on the integrated button; as soon as the exclusion

initiates, the LED indicator starts a sequence of RED-BLUE blinks. The device is excluded

from the network when the LED status indicator is solid RED and the App_status in the

interface is OK.

ENGLISH

SMARTSTART INCLUSION

Z-WaveTM SmartStart aims to shift the tasks related to inclusion of an end device into a

Z-WaveTM network away from the end device itself, and towards the more user-friendly

interface of the gateway.

Z-WaveTM SmartStart removes the need for initiating the end device to start inclusion.

Inclusion is initiated automatically on power-ON and repeated at dynamic intervals

for as long as the device is not included into a Z-WaveTM network. As the new device

announces itself on power-ON, the protocol will provide notications, and the

gateway can initiate the inclusion process in the background, without the need for user

interaction or any interruption of normal operation. The SmartStart inclusion process

only includes authenticated devices.

META Serie 7 devices can be added into a Z-WaveTM network by scanning the Z-WaveTM

QR Code present on the product with a controller providing SmartStart inclusion. No

further action is required and the SmartStart product will be added automatically

within 10 minutes of being switched on in the network vicinity.

The SmartStart QR and the full DSK string code can be found on the back of the device.

The PIN is the rst group of 5 digits printed underlined. If you plan to use the DSK, it is

important that you take a picture of the label and keep it in a safe place.

S2 SECURE INCLUSION

When adding META Serie 7 devices to a Z-WaveTM network with a controller supporting

Security 2 Authenticated (S2), the PIN code of the Z-WaveTM Device Specic Key (DSK) is

required. The unique DSK code is printed on the product label. The rst ve digits of the

key are highlighted and underlined to help the user identify the PIN code.

Pin Code

ENGLISH

SUPPORTED COMMAND CLASSES

Command Class

Version Non-Secure

Secure CC

BASIC 2

ZWAVEPLUS_INFO 2

INDICATOR 2

ASSOCIATION 2

MULTI_CHANNEL_ASSOCIATION 3

ASSOCIATION_GRP_INFO 2

TRANSPORT_SERVICE 1

VERSION 2

MANUFACTURER_SPECIFIC 2

POWERLEVEL 1

CONFIGURATION 4

SECURITY_2 1

SUPERVISION

FIRMWARE_UPDATE_MD

WINDOW_COVERING 1

MULTILEVEL 4

NOTIFICATION 9

ENGLISH

Table des matières

Autres manuels CHERUBINI Contrôleurs

CHERUBINI

CHERUBINI MyRoll Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur