Checkpoint Smart-1 series Manuel utilisateur

Classification [Protected] P/N:707305

For a list of our trademarks, please refer to: www.checkpoint.com/copyright.html.

For a list of our Third Party Copyright notices, please refer to: www.checkpoint.com/3rd_party_copyright.html

Smart-1 Installing and Removing

Memory

707305

Protected

2017

This document is for Smart-1 205, 210, 225, 3050 and 3150 models.

Important - We recommend that only experienced personnel install or

remove hardware components. Installing or removing components

incorrectly can permanently damage the Security Management

Appliance.

Preparing the Security Management

Appliance

Before you start to install or remove DIMMs, make sure that:

•You can connect to the WebUI or CLI to shut down the Security Management

Appliance.

•The Security Management Appliance is in a clean environment and on a

level surface.

•You can physically access and open the cover of the Security Management

Appliance.

•You have the Check Point DIMM upgrade kit.

Important

•To protect the Security Management Appliance and the memory modules

from electrostatic discharge damage, make sure that you are properly

grounded before you touch these components. For more, see the Health

and Safety Information in:

Smart-1 205/210 Appliances Getting Started Guide

http://supportcontent.checkpoint.com/documentation_download?ID=32280

Smart-1 225/3050/3150 Appliances Getting Started Guide

http://supportcontent.checkpoint.com/documentation_download?ID=32309

•We recommend that you use the grounding wrist strap that is included in

the upgrade kit. The grounding plug on the rear of the Security Management

Appliance provides a chassis grounding point.

Upgrade Kit Contents

•Installation guide - Smart-1 Installing and Removing Memory

•Expansion DIMMs

•Upgrade kit sticker

•ESD grounding strap (anti-static)

•Screwdriver

To prepare the Security Management Appliance:

1. From the WebUI or the CLI, shut down the Security Management Appliance.

2. Use the power switch to turn off power to the Security Management

Appliance.

3. Remove the power cords from the Security Management Appliance.

4. Put on the ESD strap and attach the other end to a grounding point.

5. Loosen the Security Management Appliance cover screws.

6. Remove the top cover from the Security Management Appliance.

The diagram shows how to remove the Smart-1 3150 cover. The Smart-1

205, Smart-1 210, Smart-1 225, and Smart-1 3050 covers are similar.

Item

Description

1 Security Management Appliance cover

2 Security Management Appliance cover screws

3 ESD grounding point - location changes according to model

Smart-1 205 and Smart-1 210 DIMM

Configuration

Item Description

1 Security Management Appliance rear panel

2 Sockets for DIMMs

3 Security Management Appliance front panel

The Smart-1 205 Security Management Appliance has a default memory

configuration of 4GB: 2x2GB, with two DIMMs.

The Smart-1 210 Security Management Appliance has a default memory

configuration of 8GB: 2x4GB, with two DIMMs.

To upgrade to Use

DIMMs

Procedure Slots

Smart-1 205

16GB

2x8GB Remove the two 2GB DIMMs and install

two 8GB DIMMs in the same slots

1 and 3

Smart-1 210

16GB

2x8GB Remove the two 4GB DIMMs and install

two 8GB DIMMs in the same slots

1 and 3

Default Upgraded Item Description

Top View

(front of the

Security

Management

Appliance is at the

top of the

diagram)

Top View

(front of the

Security

Management

Appliance is at the

top of the diagram)

Memory socket

with DIMM

installed

Expansion

memory socket

Smart-1 225 DIMM Configuration

Item Description

1 Security Management Appliance rear panel

2 Sockets for DIMMs

3 Security Management Appliance front panel

The appliance has a default memory configuration of 16GB: 2x8GB, with two

DIMMs.

To upgrade to Use

DIMMs

Procedure Slots

32GB 4x8GB Install an additional two 8GB DIMMs All

Default Upgraded Item Description

Top View

(front of the

Security

Management

Appliance is at the

bottom of the

diagram)

Top View

(front of the

Security

Management

Applianceis at the

bottom of the

diagram)

Memory socket

with DIMM

installed

Expansion

memory socket

Smart-1 3050 and Smart-1 3150 DIMM

Configuration

Smart-1 3050 with open cover Smart-1 3150 with open cover

Item

Description

1 Security Management Appliance rear panel

2 Sockets for DIMMs

3 Security Management Appliance front panel

Smart-1 3050

The Security Management Appliance has a default memory configuration of

32GB: 8x4GB, with eight DIMMs.

To upgrade to Use

DIMMs

Procedure Slots

64GB 16x4GB Install an additional eight 4GB DIMMs All

128GB 16x8GB Replace all DIMMs with sixteen 8GB

DIMMs. See diagram.

All

256GB 16x16GB Replace all DIMMs with sixteen 16GB

DIMMs

Gaia only (not supported on

SecurePlatform)

All

Smart-1 3150

The Security Management Appliance has a default memory configuration of

64GB: 8x8GB with eight DIMMs.

To upgrade to Use

DIMMs

Procedure Slots

128GB 16x8GB Install an additional eight 8GB DIMMs All

256GB 16x16GB Replace all DIMMs with sixteen 16GB

DIMMs

Gaia only (not supported on

SecurePlatform)

All

Default Configuration for Smart-1 3050, Smart-1 3150:

Top View

(front of the Security Management Appliance is at the bottom of the diagram)

Upgraded Configuration for Smart-1 3050: 64GB, 128GB, 256GB, and Smart-1

3150: 128GB, 256GB:

Top View

(front of the Security Management Appliance is at the bottom of the diagram)

Item Description

Memory socket with DIMM installed

Expansion memory socket

Autres manuels pour Smart-1 series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Checkpoint Système de sécurité

Checkpoint

Checkpoint NS40 Manuel utilisateur

Checkpoint

Checkpoint 61000 Manuel utilisateur

Checkpoint

Checkpoint CLASSIC Series Manuel utilisateur

Checkpoint

Checkpoint Neo NP10 Manuel utilisateur

Checkpoint

Checkpoint IP1280 Manuel utilisateur

Checkpoint

Checkpoint 4800 Manuel utilisateur

Checkpoint

Checkpoint 61000 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur