Charnwood W660 Mode d’emploi

TABLE SAW RIVING KNIFE ADJUSTMENT

MODEL: W660

It is possible that the factory setting of the riving knife restricts the maximum cutting

depth of the saw. If this is the case, the riving knife can be adjusted as follows:

1) Ensure that the machine is isolated from the power supply.

2) Raise the blade to its maximum height using the blade height adjustment hand

wheel at the front of the saw.

3) Remove the hose from the crown guard, remove the crown guard from the riving

knife, by loosening the black thumb screw.

4) In order to keep the Crown Guard parallel to the table, once the riving knife has

been adjusted, a slight modification will be needed to the plastic part.

Extend by 7mm

This allows the crown guard to rotate further on the pivot point and remain parallel to

the table after the adjustment. Use a sharp craft knife, carefully extend the slot at the

rear of the guard by approximately 7mm. You might find this easier if the two sides of

the guard are first split.

5) Slide the carriage fully forward to expose the riving knife attachment nut.

6) The nut holding the riving knife can now be loosened using a 16mm spanner.

7) Raise the riving knife and crown guard assembly, so that the crown guard is

situated just above the top of the saw blade. If necessary adjust the riving knife so

that there is an even gap between the leading edge of the riving knife and the radius

of the saw blade. Adjust the crown guard so that it is parallel to the table.

8) Re-tighten the bolt.

The saw can now be used to the full cutting capacity.

Autres manuels pour W660

1

Table des matières

Autres manuels Charnwood Scie

Charnwood

Charnwood W616 Manuel utilisateur

Charnwood

Charnwood W715 Manuel utilisateur

Charnwood

Charnwood 305DB Manuel utilisateur

Charnwood

Charnwood W619 Mode d’emploi

Charnwood

Charnwood TS10F Manuel utilisateur

Charnwood

Charnwood W625 Manuel utilisateur

Charnwood

Charnwood W711 Manuel utilisateur

Charnwood

Charnwood W619PSF Manuel utilisateur

Charnwood

Charnwood W616 Manuel utilisateur

Charnwood

Charnwood W730 Manuel utilisateur

Charnwood

Charnwood W721 Manuel utilisateur

Charnwood

Charnwood W650 Manuel utilisateur

Charnwood

Charnwood W715 Manuel utilisateur

Charnwood

Charnwood W629PSF Manuel utilisateur

Charnwood

Charnwood W650 Mode d’emploi

Charnwood

Charnwood W650 Manuel utilisateur

Charnwood

Charnwood W618 Manuel utilisateur

Charnwood

Charnwood W721 Manuel utilisateur

Charnwood

Charnwood BS410 Manuel utilisateur

Charnwood

Charnwood SS16F Manuel utilisateur

Charnwood

Charnwood W650 Manuel utilisateur

Charnwood

Charnwood W730 Manuel utilisateur

Charnwood

Charnwood W629 Manuel utilisateur

Charnwood

Charnwood W619 Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur