Chamberlain Liftmaster LA405-24 Manuel utilisateur

Doc 01-G0399

Rev A

Linear Actuator

Swing Gate Operator

Installation Manual

Model # LA405-24

2Contents

Doc 01-G0399

Rev A

Contents

Product Information and Specs. _____________________________________________ 3

Mechanical _________________________________________________________________________ 3

Electrical, Line Connections____________________________________________________________ 3

Electrical, Control Connections _________________________________________________________ 4

Preparations _____________________________________________________________ 5

Site Preparation______________________________________________________________________ 5

Site Layout _________________________________________________________________________ 6

Mechanical _________________________________________________________________________ 7

Electrical ___________________________________________________________________________ 8

Operating Instructions____________________________________________________ 12

Initial Test _________________________________________________________________________ 12

Functional Test _____________________________________________________________________ 14

End User Instructions ________________________________________________________________ 15

Replacement Parts _______________________________________________________ 17

Illustrated Parts _____________________________________________________________________ 17

Warranty And RGA (Returned Goods Authorization) _______________________________________ 18

Service and Tech. Reference _______________________________________________ 19

Service And Maintenance _____________________________________________________________ 19

Trouble Shooting____________________________________________________________________ 19

Product Information and Specs. 3

Doc 01-G0399

Rev A

Product Information and Specs.

The LA405-24 electromechanical gate operator can be mounted onto any swing gate up to 12 feet

wide. It is well equipped with a simple adjustable limit switch and a keyed emergency release.

Mechanical

Approx. Weight 22 lbs.

Dimensions 32.25”L x

3.625”W x

5.375”H

Max Gate Length 12 ft.

Max Gate Weight 300 lbs.

Cycles per hour 10

01-G 0399F4

Figure 1: Operator Specifications

Electrical, Line Connections

Incoming Line Voltage 115 VAC

Rated Current 1.4 Amps

Motor Voltage 24 VDC

Motor (2) Wattage 120 Watts (each)

Figure 2

4Product Information And Specs.

Doc 01-G0399

Rev A

POWER SUPPLY

The 24 DC operator requires 115 VAC power. The gauge wire depends on the distance run.

Consult your electrician to ensure a good power supply.

PROTECTION (See Figure 2)

Fuses for primary and secondary power:

1.6 Amp. 250V (line)

6.3 Amp 250V (control)

12 Amp. 250V (motor)

A varistor protects primary and secondary power over voltage. Operator torque control adjusts the

maximum output force of the operator (see Figure 13, Potentiometer #1).

CHARACTERISTICS

Solid state control panel allows the control of (2) 24 VDC, 120W actuators as follows:

Single button and Radio control command to: OPEN – STOP – CLOSE – STOP

Separate inputs for Open (with timer to close) and Stop

Timer to close built in

Safety input to stop the gate and to reverse the gate during closing cycle

Adjustable decel. speed, motor speed, motor power, and slave delay time

Electrical, Control Connections

The Eurostyle type connectors used in the LA405-24 control accept (2) stripped 16 gauge wires. Dry

contact control wires (no power) can fit more than (2) wires if smaller than 20 gauge wire is used.

Length is limited to 40 feet.

Preparations 5

Doc 01-G0399

Rev A

Preparations

Site Preparation

Using a licensed electrician, route power and control wires to the operator using appropriate conduit

and wire for your local code. Ensure gate swings freely and is level. Controls should be mounted

away from gate so people on the opposite side of the gate cannot reach through and start the gate

(see Figure 3).

NOTE: Plan gate location for accessories such as loops, photos eyes, etc. before beginning

installation.

01-G0399F12

Flashing Light

Photo Eyes

Control Box with Antenna

12 foot, 300 pount

maximum gate

Pillar for mounting

operator

Operator

Keypad/

Cardreader

Figure 3: Typical Installation

6Preparations

Doc 01-G0399

Rev A

Site Layout

NOTE: For push to open only – position plate F as shown in Figure 4.

Plate F

Push to Open

(optional)

01-G0399F15

Pull to Open

(typical)

Figure 4

Installation 7

Doc 01-G0399

Rev A

Installation

Mechanical

1 Attach plate “F” to the post so it is halfway between the ground and the

top of the gate. Refer to Figure 5.

2 Slide Plate “F” into bracket “H” and secure with bolt “E” and nut “G”.

3 When the gate is closed, attach plate “B” to the gate at the same height

as plate “F”.

4 Gate bracket “B” should be mounted approximately 23-1/4” from the gate

hinge point. The installed bracket must provide a level operation for the

operator.

5 Test the location before welding.

NOTE: When the gate is full open or full close, the unit should not

be at the end of its stroke.

01-G0399F21

Figure 5

8Installation

Doc 01-G0399

Rev A

Electrical

1. The electrical installation must meet national and local codes and should be performed by a

qualified electrician.

2. Read all manuals and safety instructions before beginning installation.

3. It is strongly recommended that safety equipment be used with this operator.

4. Power cables should be run in separate conduit from the control wiring.

5. Check all connections before applying power to units.

6. When voltage is supplied, the “Power” LED should be on.

7. If motor direction is not correct, reverse the open/close motor wires. Or as an alternate

method, you may also reverse the FCA-FCC limit switch wires.

8. The term “normally open” means that the contact points are open or apart until they are brought

together by electrical (radio receiver) or manual means (pushbutton).

9. The term “normally closed” means that the contact points are together or closed until opened

by electrical or manual means.

LINE POWER CONNECTIONS

1 Connect incoming line wires to the 3 pole terminal on control

board.

2 To attach power wires to the unit, remove the cover screw

holding black plastic power cover (see Figure 6).

This can be found in the lower right hand corner of the control

box.

3 Attach the “hot” (black), “neutral” (white) and “ground” (green)

wires as indicated on the control board. Figure 6

SAFETY DEVICES – (PHOTO EYES AND LOOP DETECTORS)

The LA 405-24 control box allows for (2) different safety inputs. The first uses terminals #1 and

#6; when activated it reverses a closing gate. The second type uses terminals #1 and #5; when

activated it stops the gate (will not open or close).

If gate was opening when obstruction occurred, once clear, the gate will continue to open. If gate

was closing when obstruction occurred, once clear, the gate will then begin reopening. Both

require connection to devices with normally closed contacts, which are opened when activated.

WARNING

Use of safety devices is recommended to prevent injury and entrapment.

STOP COMMAND

Mount a stop button near the gate. This allows the gate to be stopped in the case of an

emergency. A normally closed stop button suitable for exterior use should be used. The

connections for the stop button are #1 and #7.

Installation 9

Doc 01-G0399

Rev A

LOCKING DEVICES – (ELECTRICAL DEAD BOLT)

Locking devices may be used with the LA405-24 control panel. A 24V DC, 50W output is

maintained for 3 seconds when an open command is given. The terminal connections are #15

and #16.

RADIO CONTROLS AND SINGLE PUSH BUTTON STATIONS

Each control box comes pre-wired with a LiftMaster 412HM receiver. This receiver (or others) are

wired to terminals #1 and #2. Radio power is connected to terminals #17 (+) and #18 (-) for 24V

DC.

SAFETY EDGES

Electric gate edges are normally open devices. To wire an electric gate edge to a LA405-24

control panel, an auxiliary relay must be used. The procedure is a follows:

Attach one of the two electric gate edge wires to terminal #17

Attach the other wire to one of the coil terminals of a 24V DC relay (P/N 24-264-4)

Attach the remaining coil terminal to terminal #8

Attach the common and the normally closed contacts of the 24V DC relay to terminal #1

and #6

When the gate edge is contacted, the 24V DC relay will be energized causing an open circuit

between terminals #1 and #6.The gate operator will then reverse to the full open position.

KEYPADS/CARD READERS (See FIGURE 7)

Use terminal #1 and #3 for an open command only. The gate will time out and close if the timer

is activated.

Figure 7

AUDIO AND VISIBLE ALARMS

Warning devices may be used with the LA405-24 actuator. 24V DC, 50 W is supplied upon

opening and 3 seconds before closing. 24V DC, 50W warning devices are connected to

terminals #12 and #14.

When a safety command is received across terminals #1 and #5, actuator will stop but flasher will

continue until open or close limit switch is met.

10 Installation

Doc 01-G0399

Rev A

CONTROL CONNECTIONS

For each actuator, run (2) wires, 5 to 25 feet long of 14 gauge wire for power. Use (3) wires 16 to

20 gauge for the controls. If using (2) actuators, use motor cables of the same length and gauge

to ensure the motors run at the same speed.

NOTE: When actuator wiring is run to the bottom of the operator, mount using this hold

(!-- see Figure 8) to prevent plate from shearing cables.

01-g03099F22

Figure 8

WARNING

If operator does not stop in time, the plate may cut the cable.

Table des matières

Autres manuels Chamberlain ouvre-porte

Chamberlain

Chamberlain K1D8389-1CC Manuel de la liste des pièces

Chamberlain

Chamberlain HDSW24UL Manuel utilisateur

Chamberlain

Chamberlain SL585103U Manuel utilisateur

Chamberlain

Chamberlain MEGA SLIDE Manuel utilisateur

Chamberlain

Chamberlain GA400D Manuel utilisateur

Chamberlain

Chamberlain 1000 Series Manuel utilisateur

Chamberlain

Chamberlain APT 211 Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional LYN300KP Manuel utilisateur

Chamberlain

Chamberlain ELITE Series Manuel

Chamberlain

Chamberlain LA400 Manuel utilisateur

Chamberlain

Chamberlain SCS200 Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional BG770 Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional BG770 Guide de démarrage rapide

Chamberlain

Chamberlain Mega Arm Tower Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional BG770 Manuel

Chamberlain

Chamberlain Elite CSW200501UL Manuel utilisateur

Chamberlain

Chamberlain RSW12U Manuel utilisateur

Chamberlain

Chamberlain LMWEKITU Manuel utilisateur

Chamberlain

Chamberlain GJ Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional SL595 Manuel utilisateur

Chamberlain

Chamberlain LA400 Manuel utilisateur

Chamberlain

Chamberlain SGO500 Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional SW470 Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional BG770 Manuel utilisateur

Manuels ouvre-porte populaires d'autres marques

Elite

Elite CSW200UL Manuel utilisateur

CAME

CAME FROG-PM4 Manuel utilisateur

SOMFY

SOMFY FX230 Manuel utilisateur

Aprimatic

Aprimatic ONDA 500 Manuel utilisateur

Turnstiles

Turnstiles FSW 900 Manuel utilisateur

Erreka

Erreka BUL BL33 Mode d'emploi

Erreka

Erreka VULCAN S Manuel utilisateur

Beninca

Beninca R1-2 WBV Manuel utilisateur

Erreka

Erreka VULCAN D Manuel utilisateur

Motorline professional

Motorline professional FORT Mode d’emploi

Beninca

Beninca BOB5024 Manuel utilisateur

AGA

AGA GATEMASTER 900 HD Manuel utilisateur

SOMFY

SOMFY Dexxo RTS Pro Manuel utilisateur

Cardin

Cardin BL Series Manuel utilisateur

Westfalia

Westfalia 85 27 06 Manuel utilisateur

CAME

CAME F500 Manuel utilisateur

Extel

Extel VERA Manuel utilisateur

Comunello Automation

Comunello Automation ABACUS 220 Manuel utilisateur