REPEAT PLAYBACK
1. To select the single track repeat function,
choose the track that you want to repeat, then
press PLAY/PAUSE button to play the track.
2. Press REPEAT/ALL button once to
activate the single track repeat and the
display will flash.
3. To select the "AII Tracks Repeat" function.
Press PLAY/PAUSE button to start the track.
Press REPEAT/ALL button twice to activate
the "All Tracks Repeat" function.
PROGRAMMED PLAYBACK
1. Press PROGRAM button twice, the LED
DISPLAY showing "00", and the PROGRAM
LED IN DICATOR will both flash.
2. Press F.SKIP (FORWARD SKIP) or B.SKIP
(BACKWARD SKIP) button to select a track.
3. Press PROGRAM button again to store the
selected track number.
4. Repeat steps 2 and 3 above to program
other tracks.
5. Press PLAY PAUSE button to start
programmed playback and the PROGRAM
LED INDICATOR should light up.
6. To erase the programmed sequence, switch
the unit OFF by turning VOL/ON/OFF
(POWER ON/OFF SWITCH/ MASTER
VOLUME CONTROL) knob.
7. Press PROGRAM button in succession to
review the tracks currently memorized and
change the track number as desired.
NOTE : A maximum of 20 tracks can be
programmed to play in any order.
Caring for Compact Discs
• Treat the compact disc carefully. Handle the
compact disc only by its edge. Never allow
your fingers to come in contact with the shiny,
upprinted side of the compact disc.
• Do not attach adhesive tape, stickers, etc. to
the compact disc label.
• Clean the compact disc periodically with a
soft, lint-free, dry cloth.
• Never use detergents or abrasive cleaners to
clean the compact disc. If necessary, use a
CD cleaning kit.
• If a compact disc skips or gets stuck on a
section of the compact disc, it is probably dirty
or damaged (scratched).
• When cleaning the compact disc, wipe in
straight lines from the center of the compact
Cleaning the unit
• To prevent fire or shock hazard, disconnect
your unit from the AC power source when
cleaning.
• The finish on your unit may be cleaned with a
dust cloth and cared for as other furniture.
General
Care and Maintenance User Instructions
“C“(L R14)1.5V”
“C“(L R14)1.5V”
“C“(L R14)1.5V”
“C“(L R14)1.5V”“ C“(L R14)1.5V”
“C“(L R14)1.5V”
“C“(L R14)1.5V”“ C“(L R14)1.5V”
Operation of Power Adaptor
1. Only use a common DC 6V/600mA
power adaptor (not included)
2. Connect the power adaptor to the
DC jack.
3. For Operation only with a
short-circuit-proof safety isolating
transformer according to EN61558-2-6
or toy transformer according to
EN61558-2-7.
Battery Installation /
Replacement
1. Open the battery compartment : Loosen
the screw on the cover of battery
compartment with a screwdriver and
remove the cover.
2. Insert 4 x “C” Size (UM2 / LR14 1.5V)
type batteries (not included). Make sure
that you follow the polarity markings inside
the compartment!
3. Close the battery compartment and
tighten the screw.
disc to the outer edge of the disc, Never
wipe in circular motions.
• This unit is designed to play only compact
discs. Other discs may not conform to the
CD standard and may not play properly.
• Compact discs should be stored in their
cases after each use to avoid damage.
• Do not expose compact discs to direct
sunlight, high humidity, high temperatures, or
dust, etc. Prolonged exposure of extreme
temper atures can warp the compact disc.
• Do not stick or write anything on either side
of the compact disc.
• Sharp writing instruments or the ink may
damage the surface.
• Use caution when cleaning and wiping the
plastic parts.
• Mild soap and a damp cloth may be used on
the front panel.
56
DC 6V 600mA
WARNING: Not suitable for children
under 3 years due to small parts,
choking hazard and Strangulation
Hazard.
Use recommended type and rating of
external transformer only
Rules of using the CD player
