Cervélo C SERIES Manuel utilisateur
C SERIES MANUAL
1
INTRODUCTION
Welcome to the Cervélo family, and congratulations on your decision to enjoy a C Series bicycle.
Designed to inspire, C Series bicycles combine the exceptional lightness and stiness engineered
into every Cervélo , with a geometry designed to elevate your condence, and deliver day long riding
comfort. After 25 years of dening high performance, we are honoured to join you as you travel down
the path less taken.
This document has been prepared to guide you through the assembly of the unique features of the C
Series, but is intended only as a supplement to the assembly instructions oered by your component
manufacturer.
TABLE OF CONTENTS
Introduction............................................. 1
Frame Features........................................... 2
Fork Preparation......................................... 3
Small Parts.............................................. 5
Frame Preparation........................................ 6
Brake Housing Installation............................... 7
Mechanical Cable Routing................................. 9
Electric Cable Routing.................................. 11
Mudguard Installation................................... 13
Frame Guard Installation................................ 16
Through-Axle Wheel Installation......................... 17
Version 2 - 2018-07-05 - CER-C23-V2
2
FRAME FEATURES
A guide to your Cervélo C Series frame.
Rear dropout cable exit
Front derailleur
wire exit hole,
electric and
mechanical
Bottom bracket cable port
Down tube battery
wire hole
Down tube internal
cable ports
3
FORK PREPARATION
A
B
Max.
4mm
A 2.5mm spacer under
the Stem Cap is advised
1st Mark 2nd Mark /
Final Cut
C
D
E
F G
H
I
J
A.Stem Cap + 5mm bolt
B.Headset Spacers
C.Bearing Cap
D.Compression Ring
E.Bearings
F.Fork Insert
G.Two-Part Epoxy
H.Mixing Stick
I.Isopropyl Alcohol Wipe
J.Sandpaper (120 Grit)
1. Apply grease to the bearing seats, and Install the upper & lower
headset bearings into the head tube.
2. Fit the fork into the head tube with the complete headset,
required spacers, and the stem.
3. Apply the minimum pressure needed to ensure the assembly is
fully seated. Mark the steerer tube at the top of the stem.
4. Remove fork and clearly mark the fork steerer tube at a
point 4mm below the rst mark. Take care to verify that this
measurement is correct as this denes the cut line for the
steerer tube.
Avoid breathing the dust created during cutting carbon
composite materials.
Do not exceed 50 mm maximum total spacer height,
including the bearing cap.
4
5. To trim fork steerer, use only a saw suitable for cutting carbon,
and a cutting guide.
6. Carefully sand a bevel to the inside of the cut end of the steerer
tube to t the insert.
7. Dry t insert to check that it is ush with the cut end of the
steerer tube.
8. Use isopropyl alcohol to clean the inside of the steerer tube
and the outside of the insert.
9. Fully mix the two-part epoxy and apply to the outer surface of
the insert with the wooden mixing stick.
10. Slide the insert into the steerer while rotating it slowly until the
ared end sits ush with the top of the steerer.
11.Wipe away any excess glue from the outside surface of the
steerer tube with the isopropyl alcohol wipe.
12. Set the fork aside and allow it to sit undisturbed for the full
curing period.
Do not attempt to t the fork into a bike prior to the completion
of the full curing period.
Improper cutting of the steerer tube could cause a failure that
results in severe injury or death.
Insert should be ush
with cut end of the
fork steerer tube
5
Down Tube Cable
Stop (Mechanical)
CBS-2DT112ME
Bottom Bracket
Cable Guide
(Mechanical)
BBG-R-2013
Seat Stay
Fender Mount x2
M5x16mm
Bolt
M5 Nyloc
Flange Nut
M4x4mm
Set Screw x4
M4 Nut x4
Thread In Fender
Mount x4
Disc Hose
Bushing
BU-DH1290 x3
Front Derailleur
Wire Hole
Blanking Plug
GR-BVT-TT-S5
Down Tube
Battery Wire
Hole Blanking
Plug GR-DT-
BATTERY
Rear
Derailleur
Hanger
Rear Derailleur
Hanger Fixing Nut
C Series Fender Kit
MTA-FND112
C Series Rear
Derailleur Hanger
Assembly DRH-WMN112
Rear Derailleur
Press-In Cable
Stop (Mechanical)
CBS-DRPOUT
Rear Derailleur
Wire Guide
(Electric)
GR-DRPOUT-GUIDE
Bottom Bracket
Access Port
Rubber Blanking
Plug (Electric)
GR-BB-GUIDE
Down Tube Cable
Stop (Electric)
CBS-2DT112EL
SMALL PARTS
Designed to accommodate electronic, mechanical and hydraulic controls, the C Series frames are
engineered to provide seamless integration of all shifting systems, regardless of method or brand. In
order to do so, you will require the parts shown below:
6
Install chain catcher when installing the front
derailleur. Complete nal adjustment with the
chain in the small chainring and largest cassette
cog.Tighten the connecting bolt to 4 Nm.
Install the front derailleur
using the bolt provided
with the derailleur.
Torque to the derailleur
specications.
FRAME PREPARATION
Lightly grease Rear Derailleur Hanger Fixing
Nut and install Rear Derailleur Hanger, nger
tight. Final tightening will be done after rear
wheel installation.
Do not nal tighten rear derailleur hanger assembly
without rear wheel installed. Doing so will result in a
misaligned derailleur and poor shifting.
7
BRAKE HOUSING INSTALLATION
It is recommended that the hydraulic brake hoses or brake cable housing is installed rst. These routing
illustrations are intended as a supplement to the manufacturer’s installation instructions only. For both
hydraulic and mechanical disc brakes, please refer to the component manufacturer’s service center
or website for further information.
8
Route hydraulic brake hose or mechanical brake
housing through the frame and fork using the Disc
Hose Bushings. Install and adjust calipers as per
manufacturer’s instructions.
NOTE:The brake line
entry hole on the C3 and
C2 is on the fork's front
surface.
9
With the brake hose
already in place, install two
piece DownTube Cable
Stop (Mechanical) and
route cable housing (with
ferrules) into stop, until the
housing rests securely in
the pockets.
MECHANICAL CABLE ROUTING
It is recommended that front and rear derailleur cables be installed after the brake hose has been installed.
These routing illustrations are intended as a supplement to the manufacturer’s installation instructions
only. Please refer to the component manufacturer’s service center or website for further information.
Table des matières
Autres manuels Cervélo Vélo
Cervélo
Cervélo SOLOIST Manuel utilisateur
Cervélo
Cervélo P5X Manuel utilisateur
Cervélo
Cervélo S5 Manuel utilisateur
Cervélo
Cervélo S3 2019 Manuel utilisateur
Cervélo
Cervélo R5-CX Manuel utilisateur
Cervélo
Cervélo P5 Manuel utilisateur
Cervélo
Cervélo S5 Instructions et recettes
Cervélo
Cervélo ASPERO Manuel utilisateur
Cervélo
Cervélo PX Series Manuel utilisateur
Cervélo
Cervélo R5 Disc Manuel utilisateur
Cervélo
Cervélo R3 Rim Manuel utilisateur
Cervélo
Cervélo S5 Instructions et recettes
Cervélo
Cervélo RCA Instructions et recettes
Cervélo
Cervélo R5 Disc Manuel utilisateur
Cervélo
Cervélo S5 2023 Manuel utilisateur
Cervélo
Cervélo P5X Manuel utilisateur
Cervélo
Cervélo multi-speed racing bicycles Manuel utilisateur
Cervélo
Cervélo R5 Disc Manuel utilisateur
