Central Pneumatic 32871 Manuel utilisateur

Page 1SKU 32871 For technical questions, please call 1-800-444-3353.

3/4” HEAVY DUTY AIR IMPACT

WRENCH

ASSEMBLY and OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd. / Camarillo, CA 93011

No portion of this manual or any artwork contained herein may be reproduced in any

shape or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

Manual Revised 11h

OIL

Page 2SKU 32871 For technical questions, please call 1-800-444-3353.

SPECIFICATIONS

Free Speed 4500 RPM

Air Inlet ¼” NPT

PSI 90

CFM 7

Torque *500 maximum ft-lbs.

SAVE THIS MANUAL

You will need the manual for the safety warnings and cautions, assembly instructions, operating

procedures, maintenance procedures, trouble shooting, parts list, and diagram. Keep your invoice

with this manual. Write the invoice number on the inside of the front cover. Keep both this manual

and your invoice in a safe, dry place for future reference.

SAFETY WARNING & CAUTIONS

WARNING: When using pneumatic equipment, basic safety precautions should always be

followed to reduce the risk of personal injury and hazards due to over pressurization.

READ ALL INSTRUCTIONS BEFORE USING THIS TOOL!

1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.

2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit

locations. Don’t expose to rain. Keep work area well lit. Do not use electrically powered air

 compressorsinthepresenceofammablegasesorliquids.

3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let them

handle machines, tools, or hoses.

4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to

inhibit rust. Always lock up tools and keep out of reach of children.

5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which

it was intended. Do not use inappropriate attachments in an attempt to exceed the tool’s

capacities.

6. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool. Do not use a tool for a purpose for

which it was not intended.

7. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Non-skid footwear is recommended. Wear restrictive hair covering to contain

long hair.

8. USE EYE AND EAR PROTECTION. Always wear ANSI approved chemical splash goggles

when working with chemicals. Always wear ANSI approved impact safety goggles at other

times.

REV 04/06

Page 3SKU 32871 For technical questions, please call 1-800-444-3353.

 Wearafullfaceshieldifyouareproducingmetallingsorwoodchips.WearanANSI

approved dust mask or respirator when working around metal, wood, and chemical dusts

and mists.

9. DO NOT ABUSE THE POWER CORD. Do not yank compressor’s cord to disconnect it

from the receptacle. Do not carry tools by the cord.

10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or

across running machines.

11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer

performance. Follow instructions for lubricating and changing accessories. Inspect

compressor’s cord periodically and, if damaged, have them repaired by an authorized

technician. Inspect all hoses for leaks prior to use. The handles must be kept clean, dry, and

free from oil and grease at all times.

12. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and

adjusting wrenches are removed from the tool or machine work surface before plugging it in.

13. AVOID UNINTENTIONAL STARTING. Donotcarryanytoolwithyourngeronthetrigger,

whether it is connected to the compressor or not.

14. STAY ALERT. Watch what you are doing, use common sense. Do not operate any tool

when you are tired.

15. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should

be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment and binding of moving parts; any broken parts or mounting

 xtures;andanyotherconditionthatmayaffectproperoperation.Anypartthatisdamaged

 shouldbeproperlyrepairedorreplacedbyaqualiedtechnician.Donotusethetoolifany

switch does not turn on and off properly.

16. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use accessories

intended for use with this tool. Approved accessories are available from Harbor Freight

Tools.

17. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.

 Readwarninglabelsonprescriptionstodetermineifyourjudgmentorreexesareimpaired

while taking drugs. If there is any doubt, do not operate the tool.

18. DRAIN COMPRESSOR EVERY DAY. Do not allow moisture to build up inside the

compressor. Do not allow compressor to sit pressurized for longer than one hour.

19. MAKE SURE ALL EQUIPMENT IS RATED TO THE APPROPRIATE CAPACITY. Make

sure that regulator is set at least 10 PSI lower than the lowest rated piece of equipment you

are using.

Page 4SKU 32871 For technical questions, please call 1-800-444-3353.

UNPACKING

Your Impact Wrench comes completely assembled.

If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover

of this manual.

GENERAL

This Impact Wrench develops a maximum of 535 ft/lbs. of torque. The amount of torque can

be increased or decreased using the AIR REGULATOR (#46). When the Air Regulator is

completely screwed in it is at it’s lowest setting. Air pressure increases as you loosen the Air

Regulator.

Page 5SKU 32871 For technical questions, please call 1-800-444-3353.

OPERATION

Setup

Frequent, but not excessive, lubrication is required for best performance. Oil added through the

airline connection will lubricate internal parts. An automatic airline oiler is recommended but oil

may be added manually before every operation or after about 1 hour of continuous use. Only 4

to 5 drops of oil at a time are necessary. Too much oil will collect inside the tool and be blown

out during the exhaust cycle. ONLY USE PNEUMATIC TOOL OIL. Do not use detergent oil or

additives as these lubricants will cause accelerated wear to the seals in the tool.

Dirtandwaterintheairsupplyaremajorcausesofpneumatictoolwear.Usealter/oilerfor

betterperformanceandlongerlife.Theltermusthaveadequateowcapacityforthespecic

application.Consultthemanufacturer’sinstructionsforpropermaintenanceofyourlter.

The connector on the tool must not hold pressure when the air supply is disconnected. If the wrong

ttingisused,thetoolcanremainchargedwithairafterbeingdisconnectedandstillbeableto

drive a fastener. See Figure 1 for the recommended accessories and connection order.

Figure 1 — Airline Oiler

Page 6SKU 32871 For technical questions, please call 1-800-444-3353.

Use

Step 1: Set the compressor’s pressure regulator to a maximum of 90 PSI. 90 PSI is

satisfactory without harming this tool.

Step2: Youwillneedtopurchaseauniontting(soldseparately)beforeyoucanconnectthe

Impact Wrench to your air compressor. You may also wish to purchase an Air Coupler

as this allows quick-coupling action when using multiple tools with one compressor.

Step 3: Determine the socket size necessary for the job you need to do. Attach the appropriate

3/4” drive socket to the Impact Wrench as shown in Figure 2.

Figure 2 — Attaching the Air Coupler and Socket

Step 4: Connect the Impact Wrench to the air compressor’s hose. If leaking is detected,

disconnect the air hose and repair before use.

OIL

Air Coupler

3/4“ Drive Socket

Page 7SKU 32871 For technical questions, please call 1-800-444-3353.

Step 5: Select the power setting for Loosening by adjusting the AIR REGULATOR (#46) located

on the bottom of the Impact Wrench as shown

in Figure 3. When the Air Regulator is

completely screwed in it is at its lowest setting.

Air pressure increases as you loosen

the Air Regulator.

Figure 3 — Adjusting the Reverse Power Setting

Step 6: Select the direction of the Wrench (forward or reverse) by pushing the REVERSE

VALVE (#48) located on the handle of the Impact Wrench as shown in Figure 4.

Figure 4 — Selecting Reverse Direction

Reverse Valve

(#48)

Valve in Forward Position.

Push in to Reverse

OIL

Air Regulator

(#46)

Page 8SKU 32871 For technical questions, please call 1-800-444-3353.

Step 7: Press the TRIGGER (#38) to test the Impact Wrench. The Impact Wrench should spin

freely as shown if Figure 5.

Figure 5 — Pressing Trigger

Loosening

Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (48)

has been shifted (pressed) completely to the right. If not, refer to Steps 5

through 9 under Use before proceeding.

Step 2: Place your work in as clear a location as possible. Make sure the air hose will reach as

far as needed without stressing any connections.

Step 3: With the correct socket attached to the Impact Wrench, slide the socket over the nut or

bolt.

Step 4: Grip the Impact Wrench with both hands, especially with higher power settings. Make

sure you are in a stable position and spread your feet shoulder-width apart.

Step 5: Press the TRIGGER (#38) to loosen the bolt.

Step 6: If the bolt will not loosen, and you are on a low

power setting for Loosening, try increasing the

power setting and attempt again.

Step 7: If the bolt will not loosen with the Impact Wrench on a higher power setting, do not

repeat attempts to loosen. You may snap the bolt or strip the threads of the stud or nut.

Try another method to loosen the bolt or nut.

Trigger

(#38)

Page 9SKU 32871 For technical questions, please call 1-800-444-3353.

Tightening

Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (48)

has been shifted (pressed) completely to the left. If not, refer to Steps 5 through 9

under Use before proceeding.

Step 2: Place your work in as clear a location as possible. Make sure the air hose will reach as

far as needed without stressing any connections.

Step 3: Thread the nut or bolt on as far as possible by hand. This is to prevent cross-threading.

Step 4: If you have torque specs for the nut or bolt you are working on, refer to them. If a low

torque setting is given, it is recommended that you use a socket wrench or a manual

torque wrench to tighten as the Impact Wrench may provide too much torque, even in

the lowest power setting.

Step 5: Place the socket onto the nut or bolt.

Step 6: Grip the Impact Wrench with both hands, especially with higher power settings. Make

sure you are in a stable position and spread your feet shoulder-width apart.

Step 7: Press the TRIGGER to tighten the bolt.

Step 8: When the bolt is tight, release the TRIGGER. DO NOT OVER TIGHTEN!

MAINTENANCE

There are no user-serviceable parts in your Impact Wrench. Attempts to repair or make

adjustments on your tool are prohibited and will VOID your warranty.

Refer to OPERATIONS Setup for information on maintaining your tool.

Wipe down your tool after every use and store it in a drawer or other safe place

Page 10SKU 32871 For technical questions, please call 1-800-444-3353.

Item# Description Parts# Item# Description Parts#

1 Housing HY161-01 25 Spring Washer HY160-36

2 Set Screw HY160-45 26 Cylinder Screw HY161-19

3 Anvil Bushing HY161-02 27 Spring Washer HY161-25

4 Washer HY161-03 28 Cap Screw HY161-26

5 Anvil Collar HY161-04 29 Rubber HY161-27

6 O-Ring HY161-05 30 Protector, Rubber HY161-44

7 Anvil HY161-06 31 Oil Seal HY161-43

8 Hammer Cage HY161-07 32 Tapping Screw HY161-16

9 Bearing HY161-11 33 ExhaustDeector HY161-32

10 Oil Seal HY161-12 34 Pin HY160-32

11 O-Ring HY161-13 35 Spring HY160-31

12 Hammer Pin HY161-08 36 Set Screw HY160-16

13 Hammer Dog HY161-09 37 Spring Pin HY160-30

14 Drive Cam HY161-10 38 Trigger HY161-33

15 Front End Plate HY161-14 39 Spring Pin HY161-42

16 Rotor Blade HY161-15 40 Bushing HY160-43

17 Rotor HY161-16 41 Valve Stem HY160-06

18 Cylinder HY161-17 42 Air Control Bushing HY161-46

19 Rear End Plate HY161-18 43 Spring HY160-09

20 Oil Seal HY161-12 44 Hose Adapter HY160-10

21 Bearing NY161-20 45 O-Ring HY161-36

22 Rear Gasket NY161-21 46 Air Regulator HY161-38

23 Rear Cover HY161-22 47 Air Pipe HY161-01-1

24 O-Ring HY161-24 48 Reverse Valve HY161-35

PARTS LIST

REV 04/06

Table des matières

Autres manuels Central Pneumatic Moteur à percussion

Central Pneumatic

Central Pneumatic 93296 Manuel utilisateur

Central Pneumatic

Central Pneumatic 61718 Manuel utilisateur

Central Pneumatic

Central Pneumatic Earthquake 92353 Manuel utilisateur

Central Pneumatic

Central Pneumatic 95310 Manuel utilisateur

Central Pneumatic

Central Pneumatic 60629 Manuel utilisateur

Central Pneumatic

Central Pneumatic 94803 Manuel utilisateur

Central Pneumatic

Central Pneumatic 92921 Manuel utilisateur

Central Pneumatic

Central Pneumatic 92427 Manuel utilisateur

Central Pneumatic

Central Pneumatic 2623 Manuel utilisateur

Central Pneumatic

Central Pneumatic 94109 Manuel utilisateur

Central Pneumatic

Central Pneumatic 93566 Guide de référence rapide

Central Pneumatic

Central Pneumatic 37730 Manuel utilisateur

Central Pneumatic

Central Pneumatic Earthquake 92453 Manuel d'installation

Central Pneumatic

Central Pneumatic 93100 Manuel d'instructions d'origine

Central Pneumatic

Central Pneumatic 94802 Manuel utilisateur

Central Pneumatic

Central Pneumatic Earthquake 92421 Manuel utilisateur

Central Pneumatic

Central Pneumatic 69228 Manuel utilisateur

Central Pneumatic

Central Pneumatic 69576 Instructions de montage

Central Pneumatic

Central Pneumatic 95310 Manuel utilisateur

Central Pneumatic

Central Pneumatic 53176 Manuel utilisateur

Central Pneumatic

Central Pneumatic 94108 Manuel utilisateur

Central Pneumatic

Central Pneumatic Earthquake 92421 Manuel d'installation

Central Pneumatic

Central Pneumatic Earthquake 92353 Manuel d'installation

Central Pneumatic

Central Pneumatic Earthquake 92453 Manuel utilisateur

Manuels Moteur à percussion populaires d'autres marques

stayer

stayer IW500D Manuel utilisateur

Makita

Makita DTD152 Manuel utilisateur

Milwaukee

Milwaukee M12 FID Manuel utilisateur

Grizzly

Grizzly H6140 Manuel utilisateur

Makita

Makita BTW450 Manuel utilisateur

Ozito

Ozito LID-3000 Manuel utilisateur

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Manuel utilisateur

Greenlee

Greenlee HW3 Manuel utilisateur

Sthor

Sthor 57091 Manuel utilisateur

Makita

Makita DTD145 Manuel utilisateur

Hilti

Hilti SIW 2-A12 Manuel utilisateur

Ryobi

Ryobi R18IW3 Manuel utilisateur

Parkside

Parkside PDSSA 20-Li A1 Manuel utilisateur

Flex

Flex FX1471 Manuel utilisateur

SATA

SATA 51075C Manuel technique

Cembre

Cembre NR-11P Manuel utilisateur

Makita

Makita BTP131RFE Manuel utilisateur

DeWalt

DeWalt XR Li-ion DCF902 Manuel utilisateur