Cellink AC-0442 Manuel utilisateur

INSTALLATION GUIDE

AC-0442 15 ELEMENT

YAGI ANTENNA NEXT G

NOTE: cable must be kept clear of the reflector.

NOTE: Drain Hole must be on this side.

NOTE: These connectors must be covered with a waterproofing substance.

1/ Taking note of the antenna drain hole - slide the antenna Ubolts over the vertical boom

and tighten the nuts.

2/ Attach the feed cable (not supplied) to the antenna and run it down to the equipment.

Secure the cable to the vertical boom with cable ties (not supplied).

3/ Fit mating connector to the feed cable and attach test equipment. Check for a suitable

signal level.

If the signal level is unsatisfactory - loosen the angle adjustment screw on the angle

bracket and adjust the antenna angle for the best signal.

4/ Replace the angle adjustment screws and lock the antenna angle into place.

5/ Seal the connector union with a waterproofing compound. Vertical Mounting Boom

Ubolts

Waterproofing on connectors

NOTE: Cable must be kept in

close to the boom and clear of

the antenna elements.

Angle

adjustment

screw

20.0°

Phone: (03) 5334 2513

Web: www.wiltronics.com.au

AC-0442

-30

-25

-20

-15

-10

-5

010 20

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340 350

AC-0442

15 ELEMENT YAGI NEXT G

AC-0442 Yagi is designed foruse in a Next G fixed site installation for

Wireless Voice / Broadband Data Access.

The antenna offers 15 dBi of gain across the band 824-894 MHz.

It comes angle adjustment bracket allowing +/-20 degrees of angle

adjustment in the Vertical plane. The bracket suits up to 50mm

mounting tube.

Electrical

Frequency:

Gain (dSi):

824-894 MHz

Mechanical

Construction: Welded Aluminium consrtuction.

Grey powder coated.

Tuned Bandwth:

Operating VSWR:

Input lmp:

Vertical Beamwth:

Horizontal Beamwth:

FJB Ratio:

• Reflector length.

Horizontal

71 MHz

<1.5:1

50 ohms (Nominal)

32 '

32'

18 dB

Length (m):

'Width (m):

Weight (kg):

Termination:

Projected Area.

Wind loading @160 KPH;

Mounting:

1.156

0.18

0.6

Cable tail with N-Type

Female Receptacle.

0.05008 SQM

6.08 KG

Angle Bracket suits

25-50mm T u bing

VerticalMHZ

20.0'

780 790 800 810 820 830 840 850 860 870 880 890 900 910

1.1

1.0

1.2

1.3

1.4

1.5

-30

-20

-15

-10

-5

010 20

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340 350

-25

Phone: (03) 5334 2513

Web: www.wiltronics.com.au

Autres manuels Cellink Antenne

Cellink

Cellink ANT465 Manuel utilisateur

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

CommScope

CommScope CMAX-OMFX-43M-I53 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur