Celestron FirstScope 76EQ Fiche technique

Use the three tightening screws located at the

bottom of each leg to secure the extended legs

in place.

To set up the tripod, spread the legs outward

until they are fully extended. Extend the center

portion of each of the three tripod legs down 6-

8".

Item #31132

Quick Set-up Guide

123

All three legs should be the same length to

provide a level platform for the telescope.

Locate the equatorial mount and place the

base of the mount through the hole in the

center of the tripod mounting platform.

Properly assembled, the accessory tray should

appear as pictured above.

From underneath the tripod mounting platform,

thread the mounting bolt with washer into the

threaded hole on the bottom of the equatorial

mount.

Thread the latitude adjustment screw into the

equatorial mount until it is touching the inside

of the mount.

FirstScope 76EQ

Your FirstScope 76EQ includes: optical tube w/tube

ring attached; tripod with center support bracket;

equatorial mount; latitude adjustment screw; two

eyepieces; StarPointer finderscope; counterweight;

counterweight bar; two slow motion cables;

eyepiece accessory tray; The Sky™ CD software;

documentation including owner’s manual.

Item# 31032

Place the accessory tray on top of the tripod's

center leg brace. Thread the tray into the

threaded hole in the center of the leg brace.

Questions or Problems with Set-up?

CONTACT:

Celestron Technical Support: 310.803.5955

Quick Set-up Guide [cont]

Locate the counterweight bar and

counterweight. Slide the counterweight half

way down the counterweight bar and tighten

the locking screw to secure in place.

Thread the threaded end of the counterweight

bar into the Dec axis of the equatorial mount.

The longer cable should attach to the Right

Ascension axis and the shorter cable attaches

to the Declination axis as shown above.

Before mounting the tube, remove the two

wingnuts on the tube rings.

Place the tube on the mount by lining up the

screws with the mounting holes on the mount.

The focuser end of the telescope should be

over the counterweight assembly.

Reattach both wingnuts and tighten to secure

in place.

17 18

Orient the finderscope so that the glass

window is facing towards the front of the tube.

Place finderscope over the posts on the tube

and tighten it down with the knurled nuts.

19 20

Insert the chrome barrel of the 20mm eyepiece

into the focuser and tighten the set screw.

Remove the lens cap from the front of the

telescope. To observe, look through the

eyepiece as shown above.

Locate the finderscope. Remove the knurled

nuts on the threaded posts at the focuser end

of the telescope tube.

Slide the chrome end of the slow motion

control cables onto equatorial mount gear shaft

and tighten set screw to secure in place.

Loosen the set screw on the focuser so that it

does not obstruct the inner diameter of the

focuser.

For detailed usage information please consult your

owner’s manual.

Autres manuels Celestron Télescope

Celestron

Celestron 1510 Manuel utilisateur

Celestron

Celestron OMNI AZ 102 Manuel utilisateur

Celestron

Celestron FirstScope 90AZ Fiche technique

Celestron

Celestron NexStar 60GT Manuel utilisateur

Celestron

Celestron StarHopper 10 Manuel utilisateur

Celestron

Celestron Compustar Manuel utilisateur

Celestron

Celestron NexStar 8i Instructions d'installation et d'utilisation

Celestron

Celestron LCM Series Manuel utilisateur

Celestron

Celestron 80AZS Manuel utilisateur

Celestron

Celestron PowerSeeker2 70 Manuel utilisateur

Celestron

Celestron AstroMaster 114AZ Manuel utilisateur

Celestron

Celestron AstroMaster 70AZ Manuel utilisateur

Celestron

Celestron 91012 Manuel utilisateur

Celestron

Celestron 21072 Manuel utilisateur

Celestron

Celestron StarSense EXPLORER LT 114AZ Manuel utilisateur

Celestron

Celestron 114LCM Manuel utilisateur

Celestron

Celestron FirstScope 76 Manuel utilisateur

Celestron

Celestron NexStar 5 SE Manuel utilisateur

Celestron

Celestron FirstScope 114 Manuel utilisateur

Celestron

Celestron EdgeHD 800 Manuel utilisateur

Celestron

Celestron NexStar 80SLT Manuel utilisateur

Celestron

Celestron 22405 Manuel utilisateur

Celestron

Celestron PowerSeeker 50 Manuel utilisateur

Celestron

Celestron PowerSeeker 127EQ Fiche technique

Manuels Télescope populaires d'autres marques

Meade

Meade 81005 Condor Manuel utilisateur

Meade

Meade 114 EQ-DS Manuel utilisateur

Meade

Meade LX200 CLASSIC Manuel utilisateur

Leica

Leica 82 HD Manuel utilisateur

EASTCOLIGHT

EASTCOLIGHT 9920 Manuel utilisateur

zoomion

zoomion Genesis 200 EQ Manuel utilisateur

TEC

TEC APO 140 Manuel utilisateur

Orion

Orion 7832 Manuel utilisateur

Carson

Carson Skelescope SK-100 Manuel utilisateur

SKY-WATCHER

SKY-WATCHER VIRTUOSO Manuel utilisateur

Orion

Orion EZ Finder 7228 Manuel utilisateur

cassini

cassini C-JRS Manuel utilisateur

nedis

nedis SCTE5060WT Manuel utilisateur

Meade

Meade Polaris 60EQ-D Manuel utilisateur

PlaneWave

PlaneWave CDK700 Manuel utilisateur

William Optics

William Optics Synta Crayford Manuel utilisateur

Orion

Orion FUNSCOPE Manuel utilisateur

Levenhuk

Levenhuk Skyline Travel Manuel utilisateur