Cebora BRAVO 155 COMB Mode d'emploi

REPAIR MANUAL

for

BRAVO 155 COMBI

Art.494

20/05/98

M049400g

WARNING: All operations listed in this repair manual must be carried out by spe-

cialized, trained personnel.

This manual must be read together with instruction manual 3300627.

When working inside the machine, be especially careful of all wires, non-insulated clamps

and moving parts (motor-driven fan).

DESCRIPTION OF OPERATING LOGIC.

The machine can be started by setting the switch/selector 47 to one of the 7 settings.Power

reaches the following components directly:

1) motor-driven fan 29.

2) control circuit 48.

Now, pressing the torch trigger will close the relay RL1 (located on the circuit 48), thereby

powering the solenoid valve 22 and power transformer 32.The power transformer 32 directly

powers the rectifier 49; the positive (+) and negative (-) poles are connected to a terminal

board located in the coil compartment so that the polarity can easily be reversed if flux-cored

wire is used for welding (no gas).The voltage leaving the rectifier 49 varies in relation to the

setting of the selector switch 47, as listed in the table below:

Open circuit reference voltages for the welding machine:

Selector switch AC Volts DC Volts

setting Measured at the Measured at the

47 rectifier input rectifier output

1 21.3 18

2 23.4 19.8

3 24.4 20.8

4 26.2 22.4

5 29.5 25.4

6 31.1 26.8

7 33.7 29.1

To correctly check the open circuit output voltage from the rectifier 49, you must connect a

1.2-Kohm/10-Watt resistor in parallel to the positive (+) and negative (-) poles, then connect

the Volt meter to the same poles and press the torch trigger (the voltages listed above were

tested at a mains supply voltage of Volts 230 AC).The output voltage from the rectifier is sent

to the circuit 48 (pins n° 1 and 5 of the connector CN1), and is duly managed for use in powe-

ring the gearmotor.This voltage is regulated by the potentiometer on the circuit 48.With this

system, the speed of the gearmotor 8is linked to the position (1-7) of the selector switch 47,

and may later be regulated also by the potentiometer located on the control circuit48.The fol-

lowing are also connected to the same circuit 48:

a) the thermostat 33 (pins n° 2 and 7 of the connector CN1);

b) the torch trigger 45 (pins n° 6 and 8 of the connector CN1);

c) the gearmotor 8(pins n° 3 and 4 of the connector CN1).

To summarize: by pressing the torch trigger 45, the circuit 48 closes the relay RL1.The clo-

sed contact of the relay makes it possible to power the solenoid valve 22, the power tran-

sformer 32 and thus the rectifier 49. The output voltage from the rectifier 49 is used for two

purposes:

a) to power the gearmotor (passing through the circuit 48).

b) As welding voltage (positive and negative poles).

Set the selector switch 47 to "0" to turn off the welding machine.

NOTE: the circuit 48 is powered on terminal CN2 for machines with a V 240 AC power sup-

ply, and on terminal CN3 for machines with a V 220 AC power supply.

POSSIBLE ERRORS -TROUBLESHOOTING

Limited current distributed.

Probable causes: Remedies:

1) defective diode or diodes on the rectifier 49. a) replace the rectifier.

2) incorrect connections on the torch 45 or a) check the connections on the torch and

grounding cable 37. grounding cable.

3) defective welding voltage regulator selector a) replace the selector switch.

switch 47.

4) broken connections on the outputs from the a) restore the connection.

power transformer 32.

Excessive metal sprays during welding.

Probable causes: Remedies:

1) welding parameters incorrectly set a) find the appropriate parameters by

adjusting the selector switch 47 and

wire advancement speed potentiome-

ter.

2) welding wire moves forward irregularly a) See paragraph 6.3 of the instruction

manual 3.300.614.

3) grounding cable incorrectly connected a) make sure the connections are correct.

The relais LR1 does not close when the torch trigger is pressed.

Probable causes: Remedies:

1) defective torch trigger 45. a) make sure the trigger and its connec-

tions are in good working order

2) defective circuit 48 a) replace it.

NOTES:

always use original CEBORA spare parts.

After every repair job, all safety tests must be carried out as described in paragraph 6.1.3 of

the standard IEC 974.1.

Table des matières

Autres manuels Cebora Système de soudage

Cebora

Cebora MIG Manuel utilisateur

Cebora

Cebora MIG 1660/M Manuel utilisateur

Cebora

Cebora EVO 450 TS SYNERGIC Manuel utilisateur

Cebora

Cebora EVO 260 T Manuel utilisateur

Cebora

Cebora 381.80 Manuel

Cebora

Cebora WIN TIG AC-DC 180 M Manuel utilisateur

Cebora

Cebora MIG 3840/T Manuel utilisateur

Cebora

Cebora 476.50 Manuel utilisateur

Cebora

Cebora Rod Weld 307 cell Manuel utilisateur

Cebora

Cebora SPOOL-GUN Manuel utilisateur

Cebora

Cebora EVO 160 M COMBI Manuel utilisateur

Cebora

Cebora EVO SPEED STAR 380 TS Manuel utilisateur

Cebora

Cebora PLASMA PROF 123 Manuel utilisateur

Cebora

Cebora Synstar 200T Manuel utilisateur

Cebora

Cebora Pocket Pulse Manuel utilisateur

Cebora

Cebora SYNSTAR 330 TS Manuel utilisateur

Cebora

Cebora Power Rod 180 M Manuel utilisateur

Cebora

Cebora Spot 2500 Manuel utilisateur

Cebora

Cebora KINGSTAR 400 TS Manuel utilisateur

Cebora

Cebora 3301017 Manuel utilisateur

Cebora

Cebora BRAVO Manuel utilisateur

Cebora

Cebora WIN TIG AC-DC 270T Manuel utilisateur

Cebora

Cebora ef4-ss Manuel utilisateur

Cebora

Cebora Synstar Twin 270 T Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur