CB ELECTRONICS XPand Manuel utilisateur
CB Electronics
XPand
8 Channel Monitor Expansion
User
Guide
Provisional
XPAND 8 Channel Monitor Expansion
Contents
INTRODUCTION 1
B
LOCK
D
IAGRAM OF A
7.1.4
S
YSTEM WITH
XM
ON
7.1/5.1
SWITCH AND
S
URROUND
B
ASS
E
XTENSION
1
FRONT PANEL CONTROLS 2
CONNECTIONS 2
INSTALLATION 3
S
ETTING
XP
AND
I
NTERNAL LINKS
3
S
URROUND
B
ASS
E
XTENSION
3
7.1
TO
5.1
S
WITCHING
4
C
ONNECTING
TMC-1
OR
I
CON TO
XP
AND WITH
A-M
ON OR
XM
ON
5
ICON
TO
XM
ON AND
XP
AND WITH
AVID
C
ABLE
6
M
ALE
+F
EMALE
C
ONVERTER
6
OPERATION 7
Setup: Adv Menu 23 7
XPand Surround Format Selector 7
Solo or Mute Page: 7
Adv Menu 23 – Xpand Surround 8
Xpand User Keys 8
8 hannel 8
5.1/7.1/7.1.4 8
5.1/7.1/9.1.2 8
XPand External connections - 8 hannel Mode 9
5,1/7.1/7.1.4 10
XPand 5.1/7.1/7.1.4 with XMon 10
XPand 5.1/7.1/7.1.4 With A-Mon 11
5.1/7.1/9.1.2 12
Xpand 5.1/7.1/9.1.2 With XMon 12
Xpand 5.1/7.1/9.1.2 with A-Mon 13
I
NPUT
C
ONNECTIONS
(25
PIN
‘D’) 14
O
UTPUT
C
ONNECTIONS
(25
PIN
‘D’) 14
F
IRMWARE
PDATES
15
R
ECOVERY
M
ODE
15
CB ELECTRONICS 16
XPAND 8 Channel Monitor Expansion
21 April 2017 CB Electronics 1 Provisional
I
In
nt
tr
ro
od
du
uc
ct
ti
io
on
n
The CB XPand converts a 7.1 XMon or A-Mon system to a 7.1.4 or 9.1.2 ATMOS system by
add ng 8 extra channels to your ex st ng system.
XPand prov des up to 8 channels n the ma n nput and output path of the XMon or A-Mon.
Where only 4 channels are requ red the XPand can be used to sw tch the rear surround to
s de when sw tch ng from Atmos/7.1 to 5.1.
•Connects n parallel w th the Av d XMon v a 15 p n VGA cable and
converter box (Both are ncluded w th the XPand).
•Connects n parallel w th the Av d XMon v a 15 p n VGA cable
(Included).
•Can be controlled from Av d ICON console Mon tor Sect on
• Fully supported by XPAND Mon tor Controller
•Two modes:- 8 Channel, 4 Channel (7.1.4, 9.1.2)
•4 Channel Mode: Sw tch Rear speakers to s de n 5.1
•4 Channel Mode: Surround Bass Extens on outputs
Block Diagram of a 7.1.4 System with XMon 7.1/5.1
switch and Surround Bass xtension
RBack
Right Top Back
5.1
7.1
7.1.4
Left Surround
Right Surround
Left Back
Left Rear Base
Right Back
Gnd
Left top Front
Right Rear Base
XMon
Right top Front
LSur
Left Top Back
RSur
Left Top Front
XPand
Right Top Back
LBack
Right Top Front
Left Top Back
Th s gu de w ll ntroduce the XPand w th examples and llustrat ons
Further nformat on, the XPAND Reference manual and software upgrades can be found at
www.col nbroad.com/cbsoft/amon/XPand.html
Features
XPAND 8 Channel Monitor Expansion
21 April 2017 CB Electronics 2 Version 3.0
F
Fr
ro
on
nt
t
P
Pa
an
ne
el
l
C
Co
on
nt
tr
ro
ol
ls
s
The XPand front panel has the follow ng control and nd cators
•Power LED: On when connected to Power
•Mute LED: On when Hardware Mute s act vated and ALL nputs and outputs
are muted
•Comms LED: Ind cates commun cat ons rece ved from TMC-1. When key s
depressed or the knob s turned the LED w ll flash as the commands
are rece ved, otherw se the LED w ll flash about once a second.
•Mute Sw tch: Enable/D sable Hardware Mute, the Mute and Unmute command
from the remote w ll also d sable the Hardware Mute.
C
Co
on
nn
ne
ec
ct
ti
io
on
ns
s
The XPAND rear connectors
•Power: IEC 85-230v Input w th 325mA fuse
•8 Balanced Inputs on 25 p n ‘D’
•8 balanced Outputs on 25 p n ‘D’
•A-Mon/XMon: HD15
•TMC-1: HD15, when used w th XMon a converter s suppl ed.
•USB: Software updates and conf gurat on sett ng. The USB s also used
when controlled from the ICON to set up XPand and to cal brate the
outputs us ng the TMC-1-W n/Mac App.
XPAND 8 Channel Monitor Expansion
21 April 2017 CB Electronics 3 Version 3.0
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
XPand s housed n a 1U Rack Mount box, The 1U mount ng ears are sh pped w th the un t
and attached w th M5 CSK screws.
XPand should be mounted next to the A-Mon or XMon, a 1 meter VGA cable s ncluded to
connect between the two un ts. The connect ons w ll depend on f the or g nal XMon cable
s used. Please spec fy the cables used when order ng so that the appropr ate converter
box may be ncluded.
Setting XPand Internal links
Surround Bass xtension
Two nternal l nks are used to select outputs 5 and 6 between nputs 5&6 or the sum of the
left and r ght surround channels followed by a low pass f lter to prov de left and r ght
surround bass extens on outputs. If you w sh to use the surround bass extens on opt on on
XPand you must repos t on two l nks w th n the Un t and set the XPand conf gurat on. The
mages below show the pos t ons of these l nks.
Surround Bass Extension
Default: No Surround Bass Extens on
J4 L nks to the Left, away from board edge
XPAND 8 Channel Monitor Expansion
21 April 2017 CB Electronics 4 Version 3.0
Surround Bass Extens on Enabled
J4 L nks to R ght – Towards board edge
Once the L nks have been set the appropr ate flag must be set n the Xpand software us ng
the TMC-1 support program on Mac or W ndows v a the USB Port.
Default: No Surround Bass Extension Surround Bass Extension Enabled
7.1 to 5.1 Switching
The XPand prov des surround sw tch ng between Atmos, 7.1 and 5.1. When sw tch ng from
7.1.4 to 5.1 the rear surrounds speakers are connected to the s de surrounds. When
sw tch ng from 9.1.2 to 7.1 the front s de speakers are connected to the s de surrounds.
When sw tch ng from 9.1.2 to 5.1 the rear surrounds are connected to the s de surrounds.
XPAND 8 Channel Monitor Expansion
21 April 2017 CB Electronics 5 Version 3.0
Connecting TMC-1 or Icon to XPand with A-Mon or
XMon
XPAND uses a VGA connector for the remote. The XPAND s suppl ed w th a converter box
to allow easy connect on to the X-Mon 15 p n ‘D’. When order ng please adv se the system
setup so that we can supply the correct converter.
TMC-1 to XPand and A-Mon with VGA cable
XPand
Long DCC VGA Cable
DCC VGA
Cable A-Mon
TMC-1
Short
TMC-1 to XPand and XMon with VGA cable
TMC-1 XPand
Short DCC VGA Cable
Converter
Long DCC VGA Cable
Male
XMon
TMC-1 to XPand and XMon with AVID Cable
AVID Cable
Converter
Female
Short
Cable
TMC-1 XMon
XPand
Female
DCC VGA Cable
DCC VGA
Short
Male +
Converter
XPAND 8 Channel Monitor Expansion
21 April 2017 CB Electronics 6 Version 3.0
ICON to XMon and XPand with AVID Cable
AVID Cable
Female
Male +
XPand
Short
ICON
DCC VGA
Cable
XMon
Converter
Male+Female Converter
XPAND 8 Channel Monitor Expansion
21 April 2017 CB Electronics 7 Version 3.0
O
Op
pe
er
ra
at
ti
io
on
n
The extra XPand channels are enabled when the Main Input is routed to the Main
Output and adds up to 8 extra channels. The XPand level control will follow the
Master Gain control.
From the TMC-1
Speaker Solo Mutes and trims are controlled directly from the TMC-1 The XPand
format is enabled in the TMC-1 advanced setup.
Setup: Adv Menu 23
XPand Surround Format
Se ector
The XPand format may be set v a the
USB port or from the XPand
8 Channel: All 8 channels are used w th
a common ga n control and nd v dual
Mute and Ga n tr m
5. /7. /7. .4 or 5 ./7. /9. .2:
Channels 1-4 are used for the Atmos
Speakers
Channels 5 & 6 ate used for L/R
Surround or L/R rear bass extens on
Channels 7 & 8 are used for the L/R
Rear surround.
So o or Mute Page:
The Depress ng the Solo or Mute key w ll
sw tch between the banks to D splay
the XPand channels
XPAND 8 Channel Monitor Expansion
21 April 2017 CB Electronics 8 Version 3.0
Adv Menu 23 –
Xpand Surround
Xpand User Keys
When Ma n nput and Output selected
Atmos Enable All Xpand Outputs
7.1/5.1 D sable All Xpand Outputs
8 Channe
RearSW No Act on
Atmos Enable Top Speakers
7.1 D sable Top Speakers
5.1
XMon: XPand connect Lb to Ls and Rb to Rs
A-Mon: Not Requ red
5.1/7.1/7.1.4
RearSW Enable/D sable Rear Base Extens on n Atmos Mode
Atmos Enable Top Speakers and Lw, Rw
7.1/5.1 D sable Top Speakers, connect Lw to Ls and Rw to Rs
5.1/7.1/9.1.2
RearSW Enable/D sable Rear Base Extens on n Atmos Mode
From ICON
The XPand App on Mac/Windows
provides the following functions
1. Select between 8 Channel 7.1.4
and 9.1.2
2. Mute Outputs
3. Switch between Atmos 7.1 5.1
and Stereo
4. Enable/Disable Surround Bass
Extension
Trim speaker Outputs by +/-4dB in 0.5dB
steps
Table des matières
Autres manuels CB ELECTRONICS Contrôleurs
