Cavius 9002-00 Manuel utilisateur
PLEASE READ THIS USER GUIDE CAREFULLY
WIRELESS SMART REMOTE
Model Number: 9002-001
Developed by CAVIUS™
The Smart Remote is designed to work in
conjunction with CAVIUS™ Wireless Family Alarms.
When a Wireless Family Alarm detects smoke or re,
the Wireless Smart Remote will ash and vibrate for
instant warning. The torch function can be used to
nd escape routes at night.
PLEASE READ THE USER GUIDE
CAREFULLY BEFORE INSTALLATION
AND RETAIN FOR FUTURE USE.
CONTENTS
1. Technical information 4
2. How to connect to the Wireless Alarm Family 6
3. Installation 10
4. Test of alarms 12
5. Alarm mode 13
6. The Cavius™ Wireless Alarm Family has two
dierentalarmsignals 14
7. Alarm silence 14
8. Torch 17
9. Lowbatterysignal 17
10. Batteries replacement 18
11. Maintenance&troubleshooting 18
12. Warranty 22
3
TECHNICAL INFORMATION:
The Smart Remote can be used with both the
CAVIUS™ Wireless Alarm Family Smoke, and
Thermal Heat Alarm. The maximum number of
alarms the remote can interlink with is 32.
Wireless Alarms and Smart Remote have a 100m+
connection range. Be sure to test your alarms after
installation as RF conditions may depend on house
layouts and materials.
Diameter: 27mm
Length: 140mm
The Smart Remote is powered by 3 replaceable
Duracell or Panasonic AAA Alkaline batteries.
Please note for correct operation of the Smart
Remote device, the use of Duracell or Panasonic
batteries are required.
Interlinked by RF: 926.365 MHz
Complies to standards: RoHS, REACH, R&TTE,
EN60065, EN300-220.
Side button for torch
Torch
End cap for battery access
Magnet Holder
Learn mode switch
End button for test/hush
4 5
HOW TO CONNECT SMART REMOTE WITH WIRELESS
FAMILY ALARMS:
1. Open the end of the remote, insert batteries,
then close.
2. Slide the switch on the remote to “Learn mode”.
Do this on all other Wireless alarms also.
Normal Mode Learn Mode
6 7
3. The torch on the remote will light up to indicate that
“Learn mode” has been selected.
4. Press and hold the test button on the Smart Remote. It
will sound a sharp beep while ashing. Once this happens,
the remote then becomes the ‘master’ and will send out
a unique code to all the other Wireless Alarms that are in
‘learn mode’.
5. As the other alarms receive the unique code, they will
also start to ash (red lights).
6. Once all Wireless alarms are ashing they have been
successfully connected. The remote and all Wireless
Alarms can now be turned back to ‘normal mode’ by icking
the switch back to its original position. Alarms will then
stop ashing and will be ready to be installed.
8 9
INSTALLATION:
The body of the Smart Remote has a built-in magnet,
allowing it to be place on a fridge, or other metal surfaces.
The metal plate included with the remote can be installed
to a surface by using the screws included. The end cap of
the remote has a hole in which a lanyard can be added so
the remote can hang from a hook.
10 11
TEST OF ALARMS:
After installation, and at least once per quarter, test all your
alarms by pressing the test button on the remote to ensure
they are operating correctly and are within range of each
other.
It is recommended to check visually every week if the LED
ashes correctly on the alarm (every 48sec.).
Hold the red end button for two swipes of alarms until the
remote stops ashing, sounding and vibrating.
The remote is now transmitting a test signal to your alarms.
During the test, the Smart Remote will ash and sound.
If the Smart Remote is receiving a test signal from another
device, it will also ash and sound to indicate that it is part
of the group. Indication can be stopped by pressing the end
button.
ALARM MODE:
When one of the connected alarms is going into alarm
and sending out the RF alarm signal, the Smart Remote’s
ashlight will start ashing rapidly (stroboscope).
The Smart remote has a built in vibrator and sounder which
will follow the sound pattern of the originating alarm. During
the alarm, both the sounder and vibrator will be activated.
The torch can be switched from stroboscopic ashing to
constant on by pressing the side button.
12 13
KNOW THE SOUND OF YOUR ALARM:
CAVIUS™ Wireless alarms have one alarm sound which
will alert you to life threatening situations such as smoke
and/or heat.
Please note that only the originating alarm’s LED will ash,
so you can identify the source of the re.
Alarm signal 1 (--- --- ---) is life threatening alarms, like a
smoke alarm.
Alarm signal 2 (- - -) is a non life threatening alarm, like a
ooding alarm:
Smoke alarm signal: --- --- ---
Heat alarm signal: --- --- ---
Please note that only the originating alarm’s LED will ash,
so it can be identied.
ALARM SILENCE:
When the alarms from the Wireless Alarm Family go into
alarm, they can be hushed by a short press on the end
button of the Smart Remote.
• During the rst 30 seconds
of an alarm: Press the red
end button once and the
remote stops sounding and
vibrating, LED is still ashing.
The remote is now waiting to send out the
hush signal which will start automatically
within 30 seconds.
• After 30 seconds of an alarm:
Press the red end button once and the
remote will send out a hush signal for 13
seconds. If needed to hush several alarms,
this can be repeated as many times as necessary.
14 15
IMPORTANT NOTE: in order to silence all your Wireless
alarms immediately, the alarm that has to be turned off
rst is the alarm that originally sensed the smoke or
re (and will be ashing). This silencing can be done by
pushing the hush button or using the Smart Remote. If you
silence an alarm other than the source of the alarm, the
remaining alarms will still sound.
The Smart Remote can only stop the alarmed device after
30 seconds in alarm mode. The reason for this is to make
sure you have identied the source of the re before using
the hush function.
TORCH:
The torch can be turned on and off by pressing the side
button. Please note: The light will turn off automatically
after 5 minutes.
LOW BATTERY SIGNAL:
30 days before the battery is due to die, a short beep will
start to sound every 48 seconds.
Only the device affected by the low battery will beep,
no other connected devices will sound.
It is safe to change batteries in the Smart Remote
without going through the learn process again – it will
not forget the codes during the battery change process.
16 17
Please note: Due to coming legislation, the hush signal
is transmitted with reduced power (the remote must be
within short range from the silenced alarm, which means
you should be in the same room as the alarm).
You can hush any of your alarms in the system, as long
as you are in in the same room and within short range of
the alarm.
BATTERIES REPLACEMENT:
Access the 3 x AAA batteries by removing the end cap of
the Smart Remote.
After replacing batteries, be sure to test the Smart Remote
to ensure you have placed them in the right way and the
remote is functioning. Dispose of used batteries according
to local environmental regulations.
Note: Please ensure the correct and recommended type of
battery is used for replacement.
BATTERY MAINTENANCE:
If the Smart Remote does not work when the test/Hush
button is pushed, the probable cause is faulty batteries
which must be replaced.
issues regarding your Smart Remote.
18 19
Table des matières
Autres manuels Cavius Télécommande
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
