Casio ALGEBRA FX 2.0 Manuel utilisateur
19990401
Manual Calculations
2-1 Basic Calculations
2-2 Special Functions
2-3 Specifying the Angle Unit and Display Format
2-4 Function Calculations
2-5 Numerical Calculations
2-6 Complex Number Calculations
2-7 Binary, Octal, Decimal, and Hexadecimal Calculations
2-8 Matrix Calculations
Chapter 2
19990401
2-1-1
Basic Calculations
2-1 Basic Calculations
kk
kk
kArithmetic Calculations
•Enter arithmetic calculations as they are written, from left to right.
•Use the -key to input the minus sign before a negative value.
•Calculations are performed internally with a 15-digit mantissa. The result is rounded to a
10-digit mantissa before it is displayed.
•For mixed arithmetic calculations, multiplication and division are given priority over
addition and subtraction.
Example Operation
23 + 4.5 – 53 = –25.5 23+4.5-53w
56 ×(–12) ÷(–2.5) = 268.8 56*-12/-2.5w
(2 + 3) ×102= 500 (2+3)*1E2w*1
1 + 2 – 3 ×4 ÷5 + 6 = 6.6 1+2-3*4/5+6w
100 – (2 + 3) ×4 = 80 100-(2+3)*4w
2 + 3 ×(4 + 5) = 29 2+3*(4+5w*2
(7 – 2) ×(8 + 5) = 65 (7-2)(8+5)w*3
6= 0.3 6/(4*5)w*4
4×5
(1 + 2i) + (2 + 3i) = 3 + 5i(b+c!a(i))+(c+
d!a(i))w
(2 + i) ×(2 – i) = 5 (c+!a(i))*(c-!a(i)
)w
*1(2+3)E2 does not produce the correct
result. Be sure to enter this calculation as shown.
*2Final closed parentheses (immediately before
operation of the wkey) may be omitted, no
matter how many are required.
*3A multiplication sign immediately before an open
parenthesis may be omitted.
*4This is identical to 6 /4 /5 w.
19990401
2-1-2
Basic Calculations
*1Displayed values are rounded off to the place
you specify.
kk
kk
kNumber of Decimal Places, Number of Significant Digits, Normal
Display Range [SET UP]- [Display] -[Fix] /[Sci] /[Norm]
•Even after you specify the number of decimal places or the number of significant digits,
internal calculations are still performed using a 15-digit mantissa, and displayed values
are stored with a 10-digit mantissa. Use Rnd of the Numeric Calculation Menu (NUM)
(page 2-4-1) to round the displayed value off to the number of decimal place and number
of significant digit settings.
•Number of decimal place (Fix) and number of significant digit (Sci) settings normally
remain in effect until you change them or until you change the normal display range
(Norm) setting.
○○○○○
Example 100 ÷6 = 16.66666666...
Condition Operation Display
100/6w16.66666667
4 decimal places u3(SET UP)
cccccccccc
*1
1(Fix)ewiw16.6667
5 significant digits u3(SET UP)
cccccccccc
*1
2(Sci)fwiw1.6667E+01
Cancels specification u3(SET UP)
cccccccccc
3(Norm)iw16.66666667
19990401
2-1-3
Basic Calculations
○○○○○
Example 200 ÷7 ×14 = 400
Condition Operation Display
200/7*14w400
3 decimal places u3(SET UP)
cccccccccc
1(Fix)dwiw400.000
Calculation continues 200/7w28.571
using display capacity *Ans ×
of 10 digits 14w400.000
• If the same calculation is performed using the specified number of digits:
200/7w28.571
The value stored K5(NUM)e(Rnd)w28.571
internally is cut off to *Ans ×
the number of 14w399.994
decimal places you
specify.
kk
kk
kCalculation Priority Sequence
This calculator employs true algebraic logic to calculate the parts of a formula in the following
order:
1Coordinate transformation Pol (x, y), Rec (r,
θ
)
Differentials, quadratic differentials, integrations, Σcalculations
d/dx, d2/dx2, ∫dx, Σ, Mat, Solve, FMin, FMax, List→Mat, Seq, Min, Max, Median, Mean,
Augment, Mat →List, P(, Q(, R(, t(, List
2Type A functions
With these functions, the value is entered and then the function key is pressed.
x2, x–1, x!, °’ ”, ENG symbols, angle unit o, r, g
3Power/root ^(xy), x
4Fractions ab/c
5Abbreviated multiplication format in front of π, memory name, or variable name.
2π, 5A, Xmin, F Start, etc.
6Type B functions
With these functions, the function key is pressed and then the value is entered.
, 3, log, In, ex, 10x, sin, cos, tan, sin–1, cos–1, tan–1, sinh, cosh, tanh, sinh–1, cosh–1,
tanh–1, (–), d, h, b, o, Neg, Not, Det, Trn, Dim, Identity, Sum, Prod, Cuml, Percent, AList,
Abs, Int, Frac, Intg, Arg, Conjg, ReP, ImP
19990401
2-1-4
Basic Calculations
7Abbreviated multiplication format in front of Type B functions
2, A log2, etc.3
8Permutation, combination nPr, nCr
9×, ÷
0+, –
!Relational operators >, <, ≥, ≤
@Relational operators =, G
#and (bit operation)
$xnor, xor (bit operations)
%or (bit operation)
^And (logical operation)
Or (logical operation)
○○○○○
Example 2 + 3 ×(log sin2π2+ 6.8) = 22.07101691 (angle unit = Rad)
1
2
3
4
5
6
#When functions with the same priority are used
in series, execution is performed from right to
left.
exIn →ex{In( )}
120 120
Otherwise, execution is from left to right.
#Compound functions are executed from right to
left.
#Anything contained within parentheses receives
highest priority.
19990401
2-1-5
Basic Calculations
# Other errors can occur during program
execution. Most of the calculator’s keys
are inoperative while an error message is
displayed.
Press ito clear the error and display
the error position (see page 1-3-4).
# See the “Error Message Table” on page α-1-1
for information on other errors.
kMultiplication Operations without a Multiplication Sign
You can omit the multiplication sign (×) in any of the following operations.
• Before coordinate transformation and Type B functions (1and 6on page 2-1-3), except
for negative signs
○○○○○
Example 2sin30, 10log1.2, 2 , 2Pol(5, 12), etc.
•Before constants, variable names, memory names
○○○○○
Example 2π, 2AB, 3Ans, 3Y1, etc.
•Before an open parenthesis
○○○○○
Example 3(5 + 6), (A + 1)(B – 1), etc.
kOverflow and Errors
Exceeding a specified input or calculation range, or attempting an illegal input causes an
error message to appear on the display. Further operation of the calculator is impossible
while an error message is displayed. The following events cause an error message to appear
on the display.
•When any result, whether intermediate or final, or any value in memory exceeds
±9.999999999 ×1099 (Ma ERROR).
•When an attempt is made to perform a function calculation that exceeds the input range
(Ma ERROR).
•When an illegal operation is attempted during statistical calculations (Ma ERROR). For
example, attempting to obtain 1VAR without data input.
• When an improper data type is specified for the argument of a function calculation
(Ma ERROR).
•When the capacity of the numeric value stack or command stack is exceeded (Stack
ERROR). For example, entering 25 successive (followed by 2 +3 *4 w.
•When an attempt is made to perform a calculation using an illegal formula (Syntax
ERROR). For example, 5 ** 3 w.
19990401
•When you try to perform a calculation that causes memory capacity to be exceeded
(Memory ERROR).
•When you use a command that requires an argument, without providing a valid argument
(Argument ERROR).
•When an attempt is made to use an illegal dimension during matrix calculations
(Dimemsion ERROR).
• When an attempt is made to perform a calculation that has a real number argument and
produces a complex number solution, while “Real” is selected for the Complex Mode
setting on the SET UP Screen (Non-Real ERROR).
kMemory Capacity
Each time you press a key, either one byte or two bytes is used. Some of the functions that
require one byte are: b, c, d, sin, cos, tan, log, In, , and π. Some of the functions that
take up two bytes are d/dx(, Mat, Xmin, If, For, Return, DrawGraph, SortA(, PxIOn, Sum, and
an+1.
2-1-6
Basic Calculations
#As you input numeric values or commands,
they appear flush left on the display.
Calculation results, on the other hand, are
displayed flush right.
#The allowable range for both input and output
values is 15 digits for the mantissa and two
digits for the exponent. Internal calculations
are also performed using a 15-digit mantissa
and two-digit exponent.
19990401
2-2 Special Functions
kk
kk
kCalculations Using Variables
Example Operation Display
193.2aav(A)w193.2
193.2 ÷23 = 8.4 av(A)/23w8.4
193.2 ÷28 = 6.9 av(A)/28w6.9
kk
kk
kMemory
uVariables
This calculator comes with 28 variables as standard. You can use variables to store values
you want to use inside of calculations. Variables are identified by single-letter names, which
are made up of the 26 letters of the alphabet, plus rand
θ
. The maximum size of values that
you can assign to variables is 15 digits for the mantissa and 2 digits for the exponent.
uTo assign a value to a variable
[value] a[variable name] w
○○○○○
Example To assign 123 to variable A
Abcdaav(A)w
○○○○○
Example To add 456 to variable A and store the result in variable B
Aav(A)+efgaa
l(B)w
2-2-1
Special Functions
# Variable contents are retained even when
you turn power off.
19990401
uTo display the contents of a variable
○○○○○
Example To display the contents of variable A
Aav(A)w
uTo cl ear a variable
○○○○○
Example To clear variable A
Aaaav(A)w
uTo assign the same value to more than one variable
[value]a[first variable name*1]K6(g)6(g)4(SYBL)d(~) [last variable
name*1]w
○○○○○
Example To assign a value of 10 to variables A through F
Abaaav(A)
K6(g)6(g)4(SYBL)d(~)
at(F)w
uFunction Memory [OPTN]-[FMEM]
Function memory (f1~f20) is convenient for temporary storage of often-used expressions. For
longer term storage, we recommend that you use the GRPH •TBL Mode for expressions and
the PRGM Mode for programs.
•{Store}/{Recall}/{fn}/{SEE} ... {function store}/{function recall}/{function area specification
as a variable name inside an expression}/{function list}
2-2-2
Special Functions
*1 You cannot use “r” or “
θ
” as a variable name.
19990401
uTo st ore a function
○○○○○
Example To store the function (A+B) (A–B) as function memory number 1
(av(A)+al(B))
(av(A)-al(B))
K6(g)5(FMEM)
b(Store)bw
uTo recall a function
○○○○○
Example To recall the contents of function memory number 1
K6(g)5(FMEM)
c(Recall)bw
uTo di splay a list of available functions
K6(g)5(FMEM)
e(SEE)
2-2-3
Special Functions
#Ifthe function memory number to which you
store a function already contains a function, the
previous function is replaced with the new one.
#The recalled function appears at the current
location of the cursor on the display.
Autres manuels pour ALGEBRA FX 2.0
11
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Casio Calculatrice
Casio
Casio FX-7400GII Manuel utilisateur
Casio
Casio DC-810 Manuel utilisateur
Casio
Casio FX-9750GII - SOFTWARE VERSION 2-00 Manuel utilisateur
Casio
Casio ClassWiz fx-991EX Manuel utilisateur
Casio
Casio FX-9750G Manuel utilisateur
Casio
Casio fx-82AR X Manuel utilisateur
Casio
Casio fx-120 Manuel utilisateur
Casio
Casio fx-7400G Manuel d'instructions et de sécurité
Casio
Casio fx-115ES PLUS Manuel utilisateur
Casio
Casio FX-95 Manuel utilisateur
Casio
Casio FX-9750GII - SOFTWARE VERSION 2-00 Manuel utilisateur
Casio
Casio OH-300ES Manuel utilisateur
Casio
Casio ALGEBRA FX 2.0 Manuel utilisateur
Casio
Casio FX-180PA Manuel utilisateur
Casio
Casio fx-82MS Manuel utilisateur
Casio
Casio CFX-9800G-w - Color Graphing Calculator Manuel utilisateur
Casio
Casio DJ0120D Manuel utilisateur
Casio
Casio DL-110S Manuel utilisateur
Casio
Casio FX-100W Manuel utilisateur
Casio
Casio HR-100TM Guide de dépannage
