CASELLA CEL TUFF Standard Manuel utilisateur
CONTACT DETAILS
CASELLA CEL
Regent House,
Wolseley Road,
Kempston,
Bedford,
MK42 7JY, U.K.
Phone: +44 (0) 1234 844 100
Fax: +44 (0) 1234 841 490
Web: www.casellameasurement.com
CASELLA USA
17 Old Nashua Road,
# 15, Amherst,
NH 03031,
U.S.A.
Toll Free: +1 (800) 366 2966
Fax: +1 (603) 672 8053
Web: www.casellaUSA.com
CASELLA ESPANA
S.A.
Polígono Európolis
Calle C, nº4B
28230 Las Rozas - Madrid
Spain
Phone: + 34 91 640 75 19
Fax: + 34 91 636 01 96
Web: www.casella-es.com
CASELLA CHINA
c/o IDEAL INDUSTRIES China
Unit 911, Tower W1, Oriental Plaza,
No1 East Chang An Ave
Dong Cheng District
Beijing 100738
China
Phone: +86 10 85183141
Fax: + 86 10 85183143
Web: www.casellachina.cn
Go to Index
Casella CEL Limited
2
TABLE OF CONTENTS
PLEASE READ CAUTIONS BEFORE ATTEMPTING TO OPERATE THIS
INSTRUMENT.
SECTION TITLE PAGE
1 Introduction 5
2 Charging the Tuff Unit / Batteries 6
3 Operation Symbols 7
4 Operation 9
5 Configuration 14
6 Calibration 17
7 Renew Inlet Adapter Filter 19
8 Servicing 20
9 Fault Finding 21
10 Pump Management Software 22
11 Technical Information/Certification 35
12 Appendix 39
Casella CEL Limited 3
CAUTIONS:
The TUFFTM series of air sampling pumps are designed to be robust, however they
should not be dropped or subjected to mechanical shock. Do not suck in water, or
highly saturated or corrosive gases. Failure to comply will render the warranty invalid.
The air sampling pumps contain no user serviceable parts and if a fault is suspected
the instrument must be returned immediately to Casella CEL or to a Casella CEL
Approved Agency for repair.
The warranty does not extend to cleaning or general servicing of the instrument.
Pumps which are not in regular use, or those which have been left on the shelf for
several days, when switched on, may not display a true indication of the current battery
charge status.
To ensure accurate battery condition monitoring and charge status displays, it is
advisable to fully charge the pumps before use.
Back to Index
Casella CEL Limited
4
1. INTRODUCTION
The TUFFTM air sampling pump is produced in three models, the TUFF Standard,
TUFF Plus and TUFF Pro.
This handbook covers the entire range of TUFFTM air sampling pumps.
The TUFFTM was developed to provide sampling capabilities between 5 ml/min and 4.5
l/min, suitable for a wide range of applications including solvent fumes, asbestos
clearance and personal sampling of dusts. TUFFTM pumps are ideally suited to many of
the “Total” and “Respirable” dust sampling techniques detailed in the U.K. Health and
Safety Executive’s publication MDHS14, and in other international reference methods.
The information contained in this handbook relates only to the operation of Casella
CEL sampling equipment and is not intended to advise or influence your adopted
sampling strategy. For advice on appropriate sampling methods, refer to local
legislation and guidelines as dictated by the relevant national and regional health and
safety organisations.
Please make sure the TUFFTM and associated equipment supplied by Casella are not
damaged and the Inlet Nozzle is not restricted before attempting to use this instrument.
Figure 1 TUFFTM Air Sampling Pump
Back to Index
Casella CEL Limited 5
2. CHARGING THE TUFF PUMPS / BATTERIES
Battery Part numbers: 197088B (4.8 V, High Capacity Nickel metal- hydride or
197105B 4.8V Standard capacity).
There are two methods of charging the battery.
1. When the battery is attached to the pump.
2. The battery on its own.
This section details both methods.
Figure 2 Fit Battery to Pump and then to the Charger
•Insert pump into charging cradle as shown above.
•Fast charge starts and the red LED on the pump flashes.
•When fully charged the blue LED will illuminate. The pump can be left in the
cradle on trickle charge or may be removed.
•Individual battery packs can also be charged / stored in the cradle. The battery
pack’s own red LED will indicate that charging is in progress.
Battery Charge Mode
Note: Make sure all pumps are fully charged before use.
Casella CEL Limited
6
Figure 3 Insert Battery in Charger
•Insert battery into the charging cradle.
•Slow charge (>8-14 hours) starts. Red LED on battery illuminates.
•Battery fully charged. LED on battery holds steady illumination. The battery can
be left in cradle on trickle charge or removed.The battery charger will power
down after 5 seconds.
3. SYMBOLS DISPLAYED DURING OPERATION
During a sampling run symbols are displayed on the screen to indicate the pump
Running /Stopped status.
The symbol in the top left hand corner of the screen displays the pump mode.
Pump Running.
Pump Stopped.
Pump Paused.
The operating keys can be set in a Partial Lock Mode or Locked Mode.
Partial Lock Mode. This can be activated in Stop Mode and Run Mode. Press
the ON/OFF key three times within 3 seconds to enter Partial Lock Mode. In
this mode the pump can only be started and stopped.
Fully Locked Mode. This can only be activated in Run Mode. Press the
ON/OFF key three times within 3 seconds to enter Locked Mode. In this mode
all keys are disabled.
BATTERY GAUGE
TUFF Standard models – Battery gauge shows approximate estimate of
available battery capacity.
TUFF Plus Model- Here the battery status bar indicates approximate %
remaining.
PRO only - This screen shows the estimated life remaining based on the
current battery loading.
ERROR MESSAGES
The pump stops and an error condition is indicated by a
flashing ‘!’ and red LED. Low Battery and Flow Blockage are
shown here. After 1 minute stoppage the pump will try restart.
All error messages are displayed for 4 hours before the pump
turns off.
This symbol is displayed if the Run Time exceeds 2500hrs or
exceeds 600 charge cycles.
Back to Index
Casella CEL Limited 7
4. OPERATION
A. POWER ON
Note: To Set Language go to Configuration Chapter 5.
To start the pump, press and release the ON/OFF Key. The Firmware will run through
the initialisation screens and then automatically go to the Main Menu.
Figure 4 Power ON Screens
B. MAIN MENU (Fig. 5)
When on the Sampler will scroll through the Main Menu Options. The information
displayed on the screens will be the saved data from the last time the pump was used.
Press the ENTER key on any screen to start the pump. (Volume and Flow not
displayed on Standard Model.)
Figure 5 Main Menu
C. RUN MODE MAIN MENU (Fig. 6)
When the pump is running the Sampler will scroll through the Run Mode Menu options
and the blue led will be flashing. Current run data will be displayed. To stop the pump,
press and hold the ENTER key on any screen until the countdown is complete.
Note: PRO Model Only - Screen (Z) is the remaining run time available based on the
current flow and pressure loading. The Plus model displays the % of remaining battery
capacity only. Standard model only displays battery status bar and elapsed run time
only. No flow rate or sampled volume are displayed.
Figure 6 Run Mode Main Menu
D. STOPPED MODE MENU OPTIONS (Fig. 7)
Use the UP/DOWN keys to step through the Menu Options. Press ENTER to access a
Menu Option when it is displayed. Menu option not available in partial lock mode.
Figure 7 Menu Options
Casella CEL Limited
8
E.TIME WEIGHTED AVERAGE (TWA) PRO and PLUS ONLY (Fig. 8) (Only activated
when advanced mode is selected-see configuration chapter)
This mode allows the user to allow a known volume of sample to be taken over a
selectable time period (for example 120L over 8 hours.). In this instance if the pump
was set to 2l/min flow rate, it would only need to sample for 60 minutes over the whole
8 hour sampling duration. The pump will automatically switch on/off spreading the
sample on time over the whole duration evenly.
Use the UP/DOWN keys to step through the Menu Options until the TWA screen is
displayed.
Press ENTER to continue to the TWA Run screen. Use the UP/DOWN keys to set the
total sampling duration, e. g 8 hours.
Press ENTER to continue to the Exposure time setting. Use the UP/DOWN keys to set
the Exposure Time, e. g 1 hour.
The settings entered will provide 1 hours exposure time evenly spaced over the 8
hours running time.
Press ENTER to Start.
Figure 8 Time Weighted Average
To exit the program at any time press and hold ENTER. The display will count down 3,
2, 1 and default to the Main Menu.
F. RUN DURATION (PRO and PLUS ONLY) (Fig. 9)
Allows a pre set sampling duration time to be set e.g 6 hours.
Press ENTER to access Run Duration setup screen.
Use the UP/DOWN keys to set run duration in hours and minutes.
Press ENTER again to start the pump. The duration will be counted down and indicate
time remaining. The pump will stop when the duration end time is reached.
Figure 9 Run Duration
Casella CEL Limited 9
G. PROGRAM MODE (PRO ONLY) (Fig. 10)
Note: The Advanced Mode must be selected ON to enable this feature.
The program is configured on a PC and then uploaded into the pump. Refer to chapter
10 for details.
Note: If the pump is programmed to start sampling at 08:00 on Monday and the pump
is not switched ON until 08:10 on Monday it will not run until the next Monday at 08:00.
This example assumes the intention is to run the pump for 4 hours, then pause for 1
hour, and then resume running for another 4 hours. Use the UP/DOWN keys to step
through the Stop Mode Menu Options (See Fig. 14 for details) until PRG1 screen is
displayed.
Press ENTER to continue to the ‘ON 1’ screen. Use the UP/DOWN keys to review the
program set parameters. ON1 is 08:00. OFF1 is 12:00. PAUSE is 12:00 – 13:00.
START2 is 13:00. PROGRAM END is 17:00.
When pump is running, to exit Program Mode at any time press and hold ENTER. The
MAIN MENU’s will count own 3, 2, 1 and default to the Main Menu.
Figure 10 Program Mode
H. RESET (Fig. 11)
(Used to reset all the previous run details from display. If run details are required,
please make a note of these before reseting).
Press and hold ENTER. Release ENTER when counter is at zero.
Note: If the counter is already at zero, the Reset option is not displayed.
Figure 11 Reset Function
Casella CEL Limited
10
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels CASELLA CEL Pompe à eau
Manuels Pompe à eau populaires d'autres marques
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guide de dépannage
DUROMAX
DUROMAX XP WX Series Manuel utilisateur
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuel utilisateur
Franklin Electric
Franklin Electric IPS Manuel utilisateur
Xylem
Xylem e-1532 Series Manuel utilisateur
Milton Roy
Milton Roy PRIMEROYAL Manuel utilisateur