Carrier UPC Open Guide de configuration rapide

A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-468-01 · 1/12/2012

UPC Open i

Table of Contents

Introduction.................................................................................................................................................................. 1

What is the UPC Open?........................................................................................................................................1

Specifications ........................................................................................................................................................2

Installation ................................................................................................................................................................... 4

To mount the UPC Open ......................................................................................................................................4

Wiring the UPC Open for power..........................................................................................................................5

To wire for power................................................................................................................................... 5

To address the UPC Open....................................................................................................................................5

Configuring the BAS Port for BACnet MS/TP ...................................................................................................6

Wiring the UPC Open to the MS/TP network....................................................................................................7

Wiring specifications ............................................................................................................................. 7

To wire the UPC Open to the BAS network........................................................................................... 8

Wiring the UPC Open to the CCN network ........................................................................................................8

Wiring specifications for CCN ............................................................................................................... 9

To wire the CCN equipment to the UPC Open...................................................................................... 9

Select or create a custom control program and graphic for the UPC Open .........................................................10

Local access to the UPC Open..................................................................................................................................11

Start-up.......................................................................................................................................................................12

Configuring the UPC Open's properties.......................................................................................................... 12

Troubleshooting .........................................................................................................................................................14

The UPC Open LED's.......................................................................................................................................... 14

Serial number..................................................................................................................................................... 15

Replacing the UPC Open's battery .................................................................................................................. 15

Appendix A: Single Point Linkage and Device Address Binding............................................................................16

Single Point Linkage ......................................................................................................................................... 16

Device Address Binding .................................................................................................................................... 17

Compliance ................................................................................................................................................................18

FCC Compliance................................................................................................................................................. 18

CE Compliance ................................................................................................................................................... 18

BACnet Compliance........................................................................................................................................... 18

UPC Open 1

What is the UPC Open?

The UPC Open (Universal Protocol Card) is a general purpose protocol converter. The UPC Open can convert

proprietary equipment data into open protocol data, enabling a stand-alone, single piece of equipment to

reside on a BACnet network, where it can be monitored or controlled by a Building Automation System (BAS).

NOTE A future release of the UPC Open will support installation on a Modbus, N2, or LonWorks network.

Introduction

2 UPC Open

Specifications

Driver DRV_UPC

Maximum number of control

programs

Maximum number of

BACnet objects*

1050

* Depends on available

memory

Total available memory for application is 551244 bytes.

Obtain available memory information by viewing a module status

report after the control program is loaded.

Power 24 Vac ±10%, 50–60 Hz

10 VA power consumption (16 VA with BACview attached)

26 Vdc (25 V min, 30 V max)

Single Class 2 source only, 100 VA or less

We highly recommend using a dedicated transformer to power the

UPC Open.

BAS port (Port 1a) 3-pin port supports EIA-485 2-wire communications.

Protocols supported (DIP switch selectable):

○BACnet MS/TP

○Modbus (RTU) (future)

○Johnson N2 (future)

This port must be configured as a BAS port.

NOTE

Port 1a or LON-OC port can be used, but not both.

LON-OC port 14-pin communication port supports the LonWorks Option Card

(future)

CCN port (Port 2) 5-pin port supports EIA-485 3-wire connection to a single Carrier

CCN controller

Rnet port For SPT sensors and a BACview6in any of the following

combinations, wired in a daisy-chain configuration:

•1 SPT Plus or SPT Pro

•1–4 SPT Standards

•1–4 SPT Standards, and 1 SPT Plus or SPT Pro

Any of the above combinations, plus a BACview6, but no more than

6 devices total

Local Access port For system start-up and controller troubleshooting, use a PC with

Virtual BACview, Field Assistant, or BACview6 (115.2 kbps)

Battery 10-year Lithium CR2032 battery provides a minimum of 10,000

hours of data retention during power outages

Protection Built-in surge and transient protection circuitry - internal solid state

Polyswitches on the incoming power and network connections.

Real time clock Battery-backed real time clock keeps track of time in the event of a

power failure

Status indicators LED's indicate status of communications, running, errors, and

power.

UPC Open 3

Environmental operating

range

-22 to 150°F (-30 to 66°C), 0 to 90% relative humidity, non-

condensing

Storage temperature range -24 to 140°F (-30 to 60°C), 0 to 90% relative humidity, non-

condensing

Physical Rugged GE C2950HF Cycoloy plastic

Overall dimensions A:

5-3/16 in. (13.2 cm)

4-1/8 in. (10.5 cm)

Mounting hole dimensions C:

4-7/8 in. (12.4 cm)

2-1/20 in. (5.2 cm)

3/16 in. (.5 cm)

Panel depth 2 in. (5.1 cm)

Weight .44 lbs (.2 kg)

BACnet support Conforms to the Advanced Application Controller (B-AAC) Standard

Device Profile as defined in ANSI/ASHRAE Standard 135-2004

(BACnet) Annex L

Listed by UL-916, (Canadian Std C22.2 No. 205-M1983), CE, FCC Part 15-

Subpart B-Class A

Installation

4 UPC Open

To install the UPC Open:

1 Mount the controller (page 4).

2 Wire the controller for power. (page 5)

3 Set the controller's address. (page 5)

4 Configure the BAS port for BACnet MS/TP. (page 6)

5 Wire the controller to the MS/TP network. (page 7)

6 Wire the controller to the CCN network. (page 8)

To mount the UPC Open

When you handle the UPC Open:

•Do not contaminate the printed circuit board with fingerprints, moisture, or any foreign material.

•Do not touch components or leads.

•Handle the board by its edges.

•Isolate from high voltage or electrostatic discharge.

•Ensure that you are properly grounded.

Screw the UPC Open into an enclosed panel using the mounting slots on the coverplate. Leave about 2 in. (5

cm) on each side of the controller for wiring. Mounting hole dimensions 4.8 in. (12.2 cm) between mounting

slot center lines.

Installation

UPC Open 5

Wiring the UPC Open for power

The UPC Open is powered by a Class 2 power source. Take appropriate isolation measures when mounting

it in a control panel where non-Class 2 circuits are present. The UPC Open is a half wave device. Half wave

and full wave devices cannot share power. Examples of a full wave device are a CVC or ICVC in an applied

chiller.

Carrier controllers can share a power supply as long as you:

• Maintain the same polarity

• Use the power supply only for Carrier Open controllers

To wire for power

1 Remove power from the power supply.

2 Pull the screw terminal connector from the controller's power terminals labeled Gnd and Hot.

3 Connect the transformer wires to the screw terminal connector.

NOTE If using a grounded transformer, connect the ungrounded lead to the Hot terminal to avoid

damaging the transformer.

4 Apply power to the power supply.

5 Measure the voltage at the UPC Open’s power input terminals to verify that the voltage is within the

operating range of 21.6–26.4 Vac.

6 Insert the screw terminal connector into the UPC Open's power terminals.

7 Verify that the Power LED is on and the Run LED is blinking.

To address the UPC Open

You must give the UPC Open a MAC address that is unique on the MS/TP network. You can address the UPC

Open before or after you wire it for power

1 If the UPC Open has been wired for power, pull the screw terminal connector from the controller's power

terminals labeled Gnd and Hot. The controller reads the address each time you apply power to it.

2 Using the rotary switches, set the controller's address. Set the Tens (10's) switch to the tens digit of the

address, and set the Ones (1's) switch to the ones digit.

EXAMPLE If the controller’s address is 25, point the arrow on the Tens (10's) switch to 2 and the arrow

on the Ones (1's) switch to 5.

10's

1's

CAUTION The factory default setting is 00 and must be changed to successfully install your UPC Open.

Installation

6 UPC Open

BACnet Device Instance Address

The UPC Open also has a BACnet Device Instance address. This Device Instance MUST be unique for the

complete BACnet system in which the UPC Open is installed. The Device Instance is auto-generated by default

and is derived by adding the MAC address to the end of the Network Number. The Network Number of a new

UPC Open is 16101A. Thus, a controller with a MAC address of 20 results in a Device Instance of 16101 +

20, which is a Device Instance of 1610120. Also, using i-Vu Tools or BACView, you can configure a specific

address for the Device Instance.

Configuring the BAS Port for BACnet MS/TP

Use the same baud rate and communication settings for all controllers on the network segment. The UPC

Open is fixed at 8 data bits, No Parity, and 1 Stop bit for this protocol's communications.

1 If the UPC Open has been wired for power, pull the screw terminal connector from the controller's power

terminals labeled Gnd and Hot. The controller reads the DIP Switches and jumpers each time you apply

power to it.

2 Leave DS7 and DS8 in the OFF position. These switches are not applicable to MS/TP.

3 Set the BAS Port DIP Switches DS4 through DS6 for BACnet MS/TP. See table and example below.

Protocol DIP switch settings for MS/TP

DS8

DS7

DS6

DS5

DS4

DS3

Off Off Off Off On Off

NOTE DIP Switch DS3 is not used in i-Vu Open Control Systems.

4 Set the BAS Port DIP Switches DS1 and DS2 for the appropriate communications speed of the MS/TP

network (9600, 19.2k, 38.4k, or 76.8k bps).

Baud Selection Table

Baud Rate

DS2

DS1

9,600

Off Off

19,200

On Off

38,400

Off On

76,800

On On

5 Verify that the EIA-485 jumpers below the CCN Port are set to EIA-485 and 2W.

Autres manuels pour UPC Open

Table des matières

Autres manuels Carrier Convertisseur de média

Carrier

Carrier UPC Open Guide de configuration rapide

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur