Carlisle BINKS 30 Manuel utilisateur

The Model 30 Glass Bead Dispensing Gun delivers glass beads at the

rate of up to 20 lbs. per minute. (A pressure tank with follower plate

and bottom outlet is recommended for supply of glass beads to the

gun.) Air for atomization is not required.

“On-off” of the gun is provided by the air cylinder. It is located at the

rear of the gun body. The minimum recommended air pressure to the

cylinder is 50 PSIG.

CAUTION

The gun should never be operated without having the

guard (28) installed. All threads, including the hose

connections, should be clean of beads before mating. The

needle (15) should always be kept clean.

INSTALLATION

Mount the Model 30 gun on a 1/2” diameter steel rod. (Not furnished

with gun. Please order separately, Model 54-380.) The rod should

have a flat area to receive the mounting screw (19) for locking the

gun to the rod. Attach the air hose to the 1/4" NPS(m) nipple (21)

and attach the glass bead supply hose to the 3/4" NPS(m) inlet on the

gun head (16).

NOTE

Be sure mating threads are clean of beads.

Depending on the delivery required, select the appropriate nozzle

(orifice) insert (13) and install into the deflection nozzle (12). Install

this assembly (14) into the gun and fasten securely with retainer ring

(10) and o-ring (11).

NOTE

Be sure mating threads are clean of beads.

DISASSEMBLY INSTRUCTIONS

Read entire disassembly instructions before attempting repairs. Do

only that which is required to repair a specific trouble. Complete

disassembly may not be required.

1. Remove the screw (27) and guard (28).

2. Remove cap (3), control screw (1) and lock-nut (2). Remove

springs (4) and (5).

3. Remove nozzle assembly (14) by unscrewing retainer ring (10).

4. Using a 11/16" socket, hold piston rod (6) and loosen nut (22)

with a 7/16” wrench.

5. Unscrew needle (15) from piston rod (6) and nut (22). Remove

take-up screw (23) from gun head (16). Since o-ring (24) and

take-up screw (23) offer resistance to removal from needle (15),

unscrew take-up screw (23) from needle (15), rather than pulling

forcefully. Remove needle (15) from front of gun head (16).

6. Remove wiper (25) and retainer (26) from gun head (16).

7. Remove piston rod (6) and piston (8) by feeding air into the air

inlet (21) at 5-10 PSIG.

8. Remove screw (17) and lockwasher (18) and separate gun body

(20) from gun head (16).

ASSEMBLY INSTRUCTIONS

Before assembling gun, clean off all mating surfaces and remove any

beads clinging to them.

1. Attach gun head (16) to gun body (20) with screw (17) and

lockwasher (18).

2. Insert needle (15) through front of gun head (16). Check wiper

(25) and retainer (26) and replace if worn or damaged. Install

retainer (26) and wiper (25) through rear of gun head (16) onto

needle (15).

3. Check o-ring (24) and replace if worn or damaged. Seat o-ring

(24) correctly into take-up screw (23). Screw take-up screw

o-ring assembly (23, 24) over needle threads (15) and into gun

head (16) to finger tightness and tighten additionally 1/8 to 1/4

turn by wrench.

4. Screw nut (22) onto needle (15).

5. Check u-cup (9) and two o-rings (7) and replace if worn or

damaged. Seat two o-rings (7) correctly onto piston rod (6) and

seat u-cup (9) correctly onto piston (8). Insert piston rod (6)

through piston (8) and insert piston rod/piston assembly (6, 8)

into gun body (20).

6. Push piston rod (6) all the way into gun body (20) and hold it

there with 11/16" socket wrench. Screw needle (15) deep into

piston rod (6) while, at same time, turning nut (22), as required,

to avoid “lockup”.

7. Hold gun with nozzle end up. Insert nozzle assembly (14). Do not

install retainer ring (10).

8. Unscrew piston rod (6) with socket wrench, while pushing on

piston rod (6) and allow needle (15) to “lift” nozzle assembly (14)

3/32" off gun head (16).

9. While preventing needle (15) from turning, and while push-ing on

piston rod (6), screw nut (22) forward so as to lock against take-

up screw (23). Tighten nut (22) securely with 7/16" wrench.

10. Install spring (4) and cap (3).

11. Install spring (5), lock-nut (2) and control screw (1).

12. Select appropriate nozzle insert (13) and insert into deflection

nozzle (12). Insert nozzle assembly (14) into gun head (16).

13. Check o-ring (11) and replace if worn or damaged. Seat o-ring

(11) correctly onto gun head (16).

14. Screw retainer ring (10) onto gun head (16) and make hand

tight.

15. Attach guard (28) with screw (27) and nut (29).

MODEL 30 AUTOMATIC GLASS BEAD DISPENSING GUN

6279-0000-1 MODEL 30

6279-0000-5 MODEL 30 (BIG BORE)

77-2151-R15 (10/2020) 1 / 4 www.carlisleft.com

SERVICE MANUAL

LOCK OUT / TAG-OUT

Failure to de-energize, disconnect, lock out and tag-out all power

sources before performing equipment maintenance could cause

serious injury or death.

OPERATOR TRAINING

All personnel must be trained before operating finishing

equipment.

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture,

malfunction, or start unexpectedly and result in serious injury.

PROJECTILE HAZARD

You may be injured by venting liquids or gases that are released

under pressure, or flying debris.

PINCH POINT HAZARD

Moving parts can crush and cut. Pinch points are basically any

areas where there are moving parts.

INSPECT THE EQUIPMENT DAILY

Inspect the equipment for worn or broken parts on a daily basis.

Do not operate the equipment if you are uncertain about its

condition.

In this part sheet, the words WARNING, CAUTION and NOTE are used to

emphasize important safety information as follows:

Hazards or unsafe practices which

could result in minor personal injury,

product or property damage.

CAUTION

Hazards or unsafe practices which

could result in severe personal

injury, death or substantial property

damage.

WARNING

Important installation, operation or

maintenance information.

NOTE

Read the following warnings before using this equipment.

READ THE MANUAL

Before operating finishing equipment, read and understand all

safety, operation and maintenance information provided in the

operation manual.

WEAR SAFETY GLASSES

Failure to wear safety glasses with side shields could result in

serious eye injury or blindness.

NEVER MODIFY THE EQUIPMENT

Do not modify the equipment unless the manufacturer provides

written approval.

IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT.

FOR FURTHER SAFETY INFORMATION REGARDING THIS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300).

KNOW WHERE AND HOW TO SHUT OFF THE EQUIPMENT

IN CASE OF AN EMERGENCY

PRESSURE RELIEF PROCEDURE

Always follow the pressure relief procedure in the equipment

instruction manual.

NOISE HAZARD

You may be injured by loud noise. Hearing protection may be

required when using this equipment.

STATIC CHARGE

Fluid may develop a static charge that must be dissipated through

proper grounding of the equipment, objects to be sprayed and all

other electrically conductive objects in the dispensing area. Improper

grounding or sparks can cause a hazardous condition and result in

fire, explosion or electric shock and other serious injury.

WEAR RESPIRATOR

Toxic fumes can cause serious injury or death if inhaled.

Wear a respirator as recommended by the fluid and solvent

manufacturer’s Safety Data Sheet.

TOXIC FLUID & FUMES

Hazardous fluid or toxic fumes can cause serious injury or death if

splashed in the eyes or on the skin, inhaled, injected or

swallowed. LEARN and KNOW the specific hazards or the fluids

you are using.

KEEP EQUIPMENT GUARDS IN PLACE

Do not operate the equipment if the safety devices have been

removed.

WARNING

AUTOMATIC EQUIPMENT

Automatic equipment may start suddenly without warning.

FIRE AND EXPLOSION HAZARD

Improper equipment grounding, poor ventilation, open flame or

sparks can cause a hazardous condition and result in fire or

explosion and serious injury.

MEDICAL ALERT

Any injury caused by high pressure liquid can be serious. If you

are injured or even suspect an injury:

• Go to an emergency room immediately.

• Tell the doctor you suspect an injection injury.

• Show the doctor this medical information or the medical alert

card provided with your airless spray equipment.

• Tell the doctor what kind of fluid you were spraying or

dispensing.

GET IMMEDIATE MEDICAL ATTENTION

To prevent contact with the fluid, please note the following:

• Never point the gun/valve at anyone or any part of the body.

• Never put hand or fingers over the spray tip.

• Never attempt to stop or deflect fluid leaks with your hand,

body, glove or rag.

• Always have the tip guard on the spray gun before spraying.

• Always ensure that the gun trigger safety operates before

spraying.

77-2151-R15 (10/2020)2 / 4www.carlisleft.com

16 54-1208 GUN HEAD ...................................... 1

17 20-702-1 SCREW, HEX HEAD.............................

1/4"-20 x 7/8" Long ............................. 1

18 20-1041-1 LOCKWASHER.................................. 1

19 54-335 MOUNTING SCREW.......................... 1

20 54-1194 GUN BODY ...................................... 1

21 57-13-1 D.M. NIPPLE 1/4" NPS x 1/4" NPT ............... 1

22 20-301-1 HEX NUT 1/4"-20 ............................... 1

23 54-1198 SCREW............................................ 1

24 20-3620-5▲O-RING ........................................... 1

25 54-3114▲*WIPER ............................................ 1

26 54-3113▲*RETAINER ....................................... 1

27 20-4827 SCREW, ROUND HEAD

6-32 x 1 1/4" Long ............................. 1

28 54-1199 GUARD............................................ 1

29 20-412-1 NUT 6-32.......................................... 1

30 20-2287-1 PIPE PLUG 1/8" NPT SOC Head............... 1

— 6-1287 OPTIONAL: 1/2" BIG BORE KIT ........ 1

Binks Model 30 AUTOMATIC GLASS BEAD DISPENSING GUN

PARTS LIST

When ordering, please specify Part No.

ITEM PART

NO. NO. DESCRIPTION QTY.

ITEM PART

NO. NO. DESCRIPTION QTY.

1 54-1195 CONTROL SCREW ....................... 1

2 54-323 CONTROL SCREW LOCKNUT .......... 1

3 54-1196 CAP............................................ 1

4 54-236 SPRING ...................................... 1

5 54-1648▲SPRING ...................................... 1

6 54-1197 PISTON ROD .............................. 1

7 20-2369▲O-RING ...................................... 2

8 102-2059 PISTON ...................................... 1

9 20-3723▲U-CUP ........................................ 1

10 52-1635 RETAINER RING.......................... 1

11 20-3829▲O-RING ...................................... 1

12 45-102 ■DEFLECTION NOZZLE .344" Dia. ..... 1

13 45-103 ■NOZZLE INSERT 7/32" Dia. ............. 1

13 45-104 ■NOZZLE INSERT 1/4" Dia. .............. 1

13 45-105 ■NOZZLE INSERT 9/32" Dia. ............. 1

13 45-106 ■NOZZLE INSERT 11/32" Dia............. 1

14 45-101 DEFLECTION NOZZLE and

INSERT ASSEMBLY .................... 1

15 47-458 NEEDLE...................................... 1

▲ Also available in 6-271 Repair Kit. Please order separately.

■ Part of 45-101 Assembly.

*Also available in 54-3116 Wiper Kit. Please order separately.

Ref. Only: To convert to 1/2" nozzle, use 6-1287 Kit.

26 25

18 19

NOTE

O-ring fits in groove inside item (23).

3/4 NPS

THREAD

77-2151-R15 (10/2020) 3 / 4 www.carlisleft.com

77-2151-R15 (10/2020)4 / 4www.carlisleft.com

WARRANTY POLICY

This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty.

The use of any parts or accessories, from a source other than Carlisle Fluid Technologies,

will void all warranties. Failure to reasonably follow any maintenance guidance provided

may invalidate any warranty.

For specic warranty information please contact Carlisle Fluid Technologies.

Carlisle Fluid Technologies is a global leader in innovative nishing technologies.

Carlisle Fluid Technologies reserves the right to modify equipment specications without prior notice.

BGK™, Binks®, DeVilbiss®, Hosco®, MS®, and Ransburg®

are all registered trademarks of Carlisle Fluid Technologies, Inc.

For technical assistance or to locate an authorized distributor,

contact one of our international sales and customer support locations.

Region Industrial/Automotive Automotive Renishing

Americas Tel: 1-800-992-4657 Tel: 1-800-445-3988

Fax: 1-888-246-5732 Fax: 1-800-445-6643

Europe, Africa,

Middle East, India

Tel: +44 (0)1202 571 111

Fax: +44 (0)1202 573 488

China Tel: +8621-3373 0108

Fax: +8621-3373 0308

Japan Tel: +81 45 785 6421

Fax: +81 45 785 6517

Australia Tel: +61 (0) 2 8525 7555

Fax: +61 (0) 2 8525 7575

For the latest information about our products, visit www.carlisleft.com

Ce manuel convient aux modèles suivants

Autres manuels Carlisle Distributeur

Carlisle

Carlisle cateraide xb Instructions de montage

Manuels Distributeur populaires d'autres marques

Silver King

Silver King Majestic SK12MAJ Guide de démarrage rapide

Franke

Franke F3Dn Twin Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manuel utilisateur

DAN DRYER

DAN DRYER 282 Manuel utilisateur

Essity

Essity Tork 473208 Manuel utilisateur

CBS

CBS SD300BU-88 Guide de configuration

Sealey

Sealey MK77 Manuel utilisateur

Fluid Management

Fluid Management Accutinter 1600 Manuel utilisateur

Franke

Franke DVS SD99-010 Manuel utilisateur

Graco

Graco Dispensit 1053-10C Guide de dépannage

ITALTINTO

ITALTINTO i50 Manuel utilisateur

Coca-Cola

Coca-Cola FREESTYLE 9000 Manuel utilisateur

Graco

Graco ProMix 2KE Mode d’emploi

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manuel utilisateur

Wayne

Wayne GLOBAL VISTA CNG Manuel utilisateur

clarsen

clarsen H133 Manuel utilisateur

PicoBrew

PicoBrew Zymatic Manuel utilisateur

BOWMAN

BOWMAN BP-007 Manuel utilisateur