Carlisle BINKS 85-448 Manuel utilisateur
1 85-436 REGULATOR BODY ......................... 1
2 54-308 AIR CONNECTION, 1/4 NPS .............. 1
3 72-104 TAIL PIECE .................................... 1
4 72-93 SWIVEL NUT, 1/4 NPS ...................... 1
5 71-28 AIR CONNECTION, 1/4 NPS .............. 1
6 See Chart 1 GAUGE .......................................... 1
7 See Chart 1 SAFETY VALVE ............................... 1
8 See Chart 1 REGULATOR KIT............................. 1
9 — *▲VALVE SPRING ............................... 1
ITEM PART
NO. NO. DESCRIPTION QTY.
10 — *▲VALVE............................................ 1
11 — *▲O-RING,
(VALVE SEAT)....................... 1
12 — *▲VALVE SEAT ................................... 1
13 — *▲RELIEVING DIAPHRAGM ................. 1
14 — *▲SLIP RING ..................................... 1
15 — *▲REGULATING SPRING ..................... 1
16 — *▲BONNET ........................................ 1
17 — *▲NUT............................................... 1
18 — *▲ADJUSTING SCREW........................ 1
ITEM PART
NO. NO. DESCRIPTION QTY.
* Not available separately.
▲ Available in Kits 85-437 and 85-438. See Chart 1.
PARTS LIST
When ordering, please specify Part No.
BINKS MODEL 85-449 (0-10 PSI) AND 85-450 (0-50 PSI) PRESSURE CUP REGULATORS
To cup
(regulated)
1/4 NPS air connection
(unregulated)
1/4 NPS air
connection
(unregulated)
CHART 1
Regulator Item #6 – Gauge Item #7 – Safety
Valve Item #8 – Regulator Kit
85-449 59-299 0 –15 PSI TIA-4326 18 PSI 85-437 Low Pressure 0 –10 PSI (Red Spring)
85-450 59-369 0 –60 PSI 85-243 55 PSI 85-438 High Pressure 0 – 50 PSI (Green Spring)
77-2843-R8 (11/2020) 1 / 4 www.carlisleft.com
MODELS 85-448, 85-449 & 85-450
AIR PRESSURE REGULATORS
EN
SERVICE MANUAL
BINKS AIR PRESSURE REGULATORS
1 85-436 REGULATOR BODY ......................... 1
2 54-308 AIR CONNECTION, 1/4 NPS .............. 1
3 20-2287-1 PLUG, 1/8 NPT ................................. 2
4 72-104 TAIL PIECE .................................... 1
5 72-93 SWIVEL NUT, 1/4 NPS ...................... 1
6 54-4945 PUSH-LOK FITTING, 1/4 NPS ............ 1
7 85-438 REGULATOR KIT, (0-50 PSI)............... 1
8 — *▲VALVE SPRING ............................... 1
9 — *▲VALVE............................................ 1
ITEM PART
NO. NO. DESCRIPTION QTY.
10 — *▲O-RING, (VALVE SEAT)....................... 1
11 — *▲VALVE SEAT ................................... 1
12 — *▲RELIEVING DIAPHRAGM ................. 1
13 — *▲SLIP RING ..................................... 1
14 — *▲REGULATING SPRING ..................... 1
15 — *▲BONNET ........................................ 1
16 — *▲NUT............................................... 1
17 — *▲ADJUSTING SCREW........................ 1
ITEM PART
NO. NO. DESCRIPTION QTY.
* Not available separately.
▲ Available in 85-438 Regulator Kit.
PARTS LIST
When ordering, please specify Part No.
BINKS MODEL 85-448 PRESSURE REGULATOR FOR ROTARY AGITATOR CONTROL
1/4 NPS air
connection
(unregulated)
Connect to 85-449 or 85-450
(unregulated)
1/4" tube connection
(regulated)
EN
77-2843-R8 (11/2020)2 / 4www.carlisleft.com
REGULATOR DISASSEMBLY, CLEANING AND REASSEMBLY
DISASSEMBLY
1. Turn regulator knob counterclockwise until it
stops.
2. Unscrew the bonnet from the regulator body,
remove adjusting screw and nut, then the
regulating spring,
slip ring, and diaphragm. Unscrew the valve seat
and o-ring assembly using a screwdriver. Then
remove the valve and valve spring.
CLEANING
1. Clean parts using warm water and soap.
2. Inspect all parts.
3. Replace damaged parts.
REASSEMBLY
1. At reassembly, apply a small amount of Gunners
Mate lubricant (6-429) to the adjusting screw
threads.
2. Torque the valve seat to 4-6 inch-lbs. Torque
the bonnet to 50-60 inch-lbs.
REGULATOR OPERATION
OPERATION
Binks models 85-448, 85-449 and 85-450 regulators
are flow-thru regulators offering virtually no
restriction for spray painting applications.
Efficient, low flow, regulated parts allow for easy
control of cup (fluid) pressure and/or rotary agitator
speed.
The following conditions must be observed:
1. Do not exceed 100 PSI inlet pressure.
2. When reducing the regulator setting, it is
necessary to relieve fluid supply cup of its
previously set pressure.
WARNING
Risk of injury from pressurized components. Turn off inlet
air pressure and bleed off remaining pressure before dis-
assembly.
!
CAUTION
Do not immerse this regulator in solvent or allow solvents
to enter any of the regulator openings. When using a gun
cleaning cabinet, remove the regulator before cleaning
the gun.
!
FOR FURTHER SAFETY INFORMATION REGARDING BINKS AND DEVILBISS EQUIPMENT,
SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300).
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT.
EN
77-2843-R8 (11/2020) 3 / 4 www.carlisleft.com
EN
77-2843-R8 (11/2020)4 / 4www.carlisleft.com
WARRANTY POLICY
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Carlisle Fluid Technologies,
will void all warranties. Failure to reasonably follow any maintenance guidance provided
may invalidate any warranty.
For specic warranty information please contact Carlisle Fluid Technologies.
Carlisle Fluid Technologies is a global leader in innovative nishing technologies.
Carlisle Fluid Technologies reserves the right to modify equipment specications without prior notice.
BGK™, Binks®, DeVilbiss®, Hosco®, MS®, and Ransburg®
are all registered trademarks of Carlisle Fluid Technologies, Inc.
©2020 Carlisle Fluid Technologies, Inc.
All rights reserved.
For technical assistance or to locate an authorized distributor,
contact one of our international sales and customer support locations.
Region Industrial/Automotive Automotive Renishing
Americas Tel: 1-800-992-4657 Tel: 1-800-445-3988
Fax: 1-888-246-5732 Fax: 1-800-445-6643
Europe, Africa,
Middle East, India
Tel: +44 (0)1202 571 111
Fax: +44 (0)1202 573 488
China Tel: +8621-3373 0108
Fax: +8621-3373 0308
Japan Tel: +81 45 785 6421
Fax: +81 45 785 6517
Australia Tel: +61 (0) 2 8525 7555
Fax: +61 (0) 2 8525 7575
For the latest information about our products, visit www.carlisleft.com
Ce manuel convient aux modèles suivants
2
Autres manuels Carlisle Contrôleurs
Carlisle
Carlisle Binks 85-440 Manuel utilisateur
Carlisle
Carlisle BINKS 84-410 Manuel utilisateur
Carlisle
Carlisle Binks 84-409 Manuel utilisateur
Carlisle
Carlisle MS Elite 461959 B Series Manuel utilisateur
Carlisle
Carlisle Ransburg 9060 Manuel utilisateur
Carlisle
Carlisle BINKS 85-214 Manuel utilisateur
Carlisle
Carlisle Binks 84-407 Manuel utilisateur
Carlisle
Carlisle Ransburg DynaFlow 77376 Manuel utilisateur
Carlisle
Carlisle BINKS 85-445 Manuel utilisateur
Carlisle
Carlisle Ransburg 9060 HV2 Manuel utilisateur
Carlisle
Carlisle Ransburg DR-1 Manuel utilisateur
Carlisle
Carlisle BINKS 85-435 Manuel utilisateur
Carlisle
Carlisle DeVILBISS HGB Series Manuel utilisateur
Carlisle
Carlisle Ransburg Manuel utilisateur
Carlisle
Carlisle BINKS 84-520 Manuel utilisateur
Carlisle
Carlisle Binks 85-441 Manuel utilisateur
Carlisle
Carlisle BINKS DEVILBISS HAR-600 Manuel utilisateur
Carlisle
Carlisle 81-540 Manuel utilisateur
Carlisle
Carlisle Ransburg MicroPak 2e Manuel utilisateur
Carlisle
Carlisle Binks 107757 Manuel utilisateur
