Carel Easy PJEZS Series Manuel utilisateur

CAREL SERIES REFRIGERATION CONTROL –FIELD SUPPORT GUIDE

1. Overview of the Easy control’s display and buttons:

2. Wiring the control’s connections correctly: Carel controls come in a wide variety of different configurations, often

customized for the OEM appliance manufacturer. A label found on top of the control will show a wiring guide and electrical

specifications for the specific model. When replacing the control, DO NOT ASSUME that the numbered terminals will always serve

the same function as the previous control installed. Carefully check all connections according to the labels / symbols shown

underneath each numbered contact.

Common Configurations: PJEZS* Models –Medium Temp PJEZC* Models –Low Temp

Carefully note the following connections available on your model, and connect the wires accordingly.

Temperature probe input(s)

Control probe (AMB) and optional defrost probe (DEF), with a common

Digital input

Configurable input for alarm, defrost, curtain etc. (Parameter A4)

Compressor output

Contact points may vary across different control models

Fan output

Contact points may vary across different control models

Defrost output

Contact points may vary across different control models

Auxiliary output

Contact points may vary across different control models

Line voltage to outputs

Typically isolated from supply voltage, requiring its own connection

Supply voltage

L/N

Line and neutral supply wires, most commonly points 6 and 7

3. Viewing and changing the set point: Press and hold the red SET button for 1 second to view current set point,

and release immediately after it is displayed. (Display may flash, indicating the value can be changed.)

Press UP and DOWN arrows to change value and press SET again to store new value.

4. Programming the control / customizing the functions:

6. Troubleshooting common alarms: (Alarm indicator will light, and the code will alternate with the temperature on the display

until the condition is corrected and /or alarm is reset.)

Probe 1 Error –replace control probe

Probe 2 Error –replace defrost probe

Hi Temp Alarm –no refrigeration

Low Temp Alarm –cooling below set point

Defrost Timeout –check defrost probe

Dirty Condenser –from probe 3 (A4=10)

7. “Display alternates ‘OFF’ / Temp”: Controller is in OFF status. Press and hold power button for 3s to toggle ON / OFF.

8. If icons are blinking: the controller is calling for this activation, but a delay is keeping this activation off for a period of a set

time (i.e. minimum compressor off time of “x” minutes as a compressor protector).

9. Controller is cooling below the set point: first check if the compressor icon is blinking (Continuous Cycle mode). If blinking,

hold both UP and DOWN arrow together for 3 seconds to deactivate continuous cycle. If compressor icon is not lit but compressor

still runs, troubleshoot the appliance’s compressor, wiring, external contactor, or the control’s output for an electrical short.

10. Not Starting / Skipping Defrost: check if defrost has been disabled by parameter (operating mode) [0 = direct+defrost;

1 = direct (cooling only, no defrost); 2 = reverse (heating)] Also, check the defrost parameters decsibed above.

Is set to terminate defrost by TEMPERATURE? If so, check that the defrost probe is accurate and paramter is correct.

Is set to terminate defrost by TIME? If so, confirm paramters and are correct. (A value of 0 in either will disable defrost.)

Table des matières

Autres manuels Carel Contrôleurs

Carel

Carel MCHRTF Series Manuel utilisateur

Carel

Carel pRack pR300T Manuel utilisateur

Carel

Carel FCS Series Manuel utilisateur

Carel

Carel Rsf077 Manuel utilisateur

Carel

Carel ADE 10 Series Manuel utilisateur

Carel

Carel CR72 Series Manuel utilisateur

Carel

Carel ADP 30 pAD Series Manuel utilisateur

Carel

Carel c.pCO sistema Manuel utilisateur

Carel

Carel UltraCella WB000S F0 Series Mode d’emploi

Carel

Carel uC2SE Manuel utilisateur

Carel

Carel PRK300L3FK Manuel utilisateur

Carel

Carel DN33 Universale Series Mode d’emploi

Carel

Carel ir33+ Manuel utilisateur

Carel

Carel AT-th Tune Manuel utilisateur

Carel

Carel ir33 platform Manuel utilisateur

Carel

Carel EASY FREEZE Manuel utilisateur

Carel

Carel mPCII Manuel utilisateur

Carel

Carel PSOPZKEY00/A0 Manuel utilisateur

Carel

Carel ir33 smart Guide de l'utilisateur

Carel

Carel pCO1 series Manuel utilisateur

Carel

Carel boss Series Manuel utilisateur

Carel

Carel PlantWatchPRO PV3W Manuel utilisateur

Carel

Carel PJEZ G Series Manuel utilisateur

Carel

Carel universal infrared series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur