Car Solutions CS9100 Manuel utilisateur

Version 3.1 22/01/2011

CS9100 Installation in Subaru Cars

Disconnect the negative terminal of the accumulator before installing the CS9100 to avoid errors

in the ECU. In order to install CS9100, remove the original navigation system.

1. Unplug the connectors of the original navigation system (most often located under front passenger

seat) and remove it.

2. Connect one end of the Subaru interface cable (Fig. 1) to CS9100 (the 8-pin connector to the DATA

soc et, and the 9-pin connector to the RGB soc et). Connect the other end of the Subaru interface

cable (with a 13-pin soc et) to the 13-pin connector of the original navigation system.

Figure 1

3. Connect the CS9100 power supply cable to the CN100 connector’s wiring of the original

navigation system. (Fig. 2)

Figure 2

Version 3.1 22/01/2011

How to install the GPS antenna

Removal of the original navigation system allows you to connect CS9100 to the car’s original GPS

antenna. The best way to do this is to desolder the plastic soc et (Fig. 3) from the original wiring and solder

a 10cm coaxial cable fitted with a SMA Male connector (Fig. 4) with the wiring. The CS9100 navigation

system is fully compatible with the original antenna in all specifications.

Figure 3

Figure 4

On the other hand, you can use CS9100 with the GPS antenna that comes with it. For better signal pic up,

install the new GPS antenna in the rear spoiler (Fig. 5) (cable length allows for such installation). If there is

no rear spoiler, a fin-shaped antenna (Fig.6) can be used (it is not included with CS9100). You can also

install the CS9100 antenna (Fig. 7) under the windshield, over or under the plastic panel (Fig. 5).

Figure 5

Figure 6

Figure 7

When installing the GPS antenna in a concealed position, make sure there is no metal above it.

Installed the GPS antenna with the magnetic base down. (Fig. 7).

If your windshield and windows are made of thermal glass, install the GPS antenna on the roof

or rear spoiler.

Version 3.1 22/01/2011

When you switch on the CS9100 navigator for the first time, handle all setup procedures using the

remote control or a USB mouse.

If CS9100 doesn’t respond to the remote control, you’ll need to synchronize them. Press Return and

Home simultaneously and hold for 1s. Synchronous flashing of LEDs indicates a successful synchronization.

For correct operation of the navigation system, activate an appropriate control protocol:

1. Use the remote control to enter Settings in the main menu.

2. Choose System Config (Fig. 8).

3. Go to the Panel I tab.

4. Choose the Kenwood protocol (Fig. 9).

5. Press SAVE.

Figure 8

Figure 9

To be able to control the navigation system using the original touch panel without the remote

control, you’ll need to calibrate it:

1. Use the remote control to enter Settings in the main menu.

2. Choose Calibration.

3. Use a stylus from a PDA or any other non-sharp object to clic on the mar s that appear on

the screen. (Fig. 10)

4. Press EXIT.

Figure 10

Once you finish all setup procedures you can activate Autorun of the navigational software (or any

other software) in the Settings menu (Fig. 8).

This type of connection works only for cars with an external DVD navigation system.

You don’t have to cut off the wire connectors of the original navigation system. It is sufficient

to cut into the original wires.

Table des matières

Autres manuels Car Solutions Système de navigation automobile

Car Solutions

Car Solutions QNAVI4-MAIN-V1.1 Manuel utilisateur

Car Solutions

Car Solutions QROI2-RGB Manuel utilisateur

Car Solutions

Car Solutions Q-ROI-ONE-5 Series Manuel utilisateur

Car Solutions

Car Solutions QROI2-RGB Manuel utilisateur

Car Solutions

Car Solutions QROI X Android System Manuel utilisateur

Car Solutions

Car Solutions CS9320A Manuel utilisateur

Car Solutions

Car Solutions CS 9320 Manuel utilisateur

Car Solutions

Car Solutions Roik 4G Manuel utilisateur

Car Solutions

Car Solutions q-roi Manuel utilisateur

Car Solutions

Car Solutions M2C-200 Manuel utilisateur

Car Solutions

Car Solutions QNAVI-1CH-MAIN-2.5 Manuel utilisateur

Car Solutions

Car Solutions MC8088HLC Manuel utilisateur

Car Solutions

Car Solutions Q-ROI-INFINITY q50 Manuel utilisateur

Car Solutions

Car Solutions Q-ROIX Manuel utilisateur

Car Solutions

Car Solutions MB2019-NTG6.0-TC2 Manuel utilisateur

Car Solutions

Car Solutions CS9900 Manuel utilisateur

Manuels Système de navigation automobile populaires d'autres marques

Clarion

Clarion Navigation In-Car Entertainment Manuel utilisateur

Rosen

Rosen DP-1001 Manuel utilisateur

Alpine

Alpine INE-W970HD Manuel utilisateur

Skoda

Skoda AMUNDSEN+ Manuel utilisateur

Blaupunkt

Blaupunkt TravelPilot DX-N Manuel utilisateur

Pioneer

Pioneer MZ360500EX Manuel utilisateur

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Manuel utilisateur

Kenwood

Kenwood DNN991HD Manuel utilisateur

AvMap

AvMap Geosat 2C Manuel utilisateur

Eonon

Eonon GE01B Manuel utilisateur

Pioneer

Pioneer AVIC-Z920DAB Manuel utilisateur

Nextar

Nextar M3-MX - Automotive GPS Receiver Manuel utilisateur

Furrion

Furrion NV2200 Manuel utilisateur

Mio

Mio MOOV 200-Series Manuel utilisateur

Prestigio

Prestigio GeoVision 5150 Manuel utilisateur

Hummer

Hummer 2006 H3 Manuel utilisateur

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Guide de configuration

Garmin

Garmin StreetPilot c510 Manuel utilisateur