Canon VB-H45 Manuel utilisateur

Work Support Manual

"Device Startup"

[Ver. 1.3] March 2019

* This manual is still in

development, and is provided

only for supplemental use in

verification procedures. It should

not be distributed to the general

public. Please be aware that

some of the information that is

included is not complete, and

that it should only be used as a

reference for launching the

platform.

Introduction

The purpose of this manual is to quickly learn the image processing configuration

procedure using a Canon network camera and Vision Edition.

When applying the operations to an actual production system, be sure to check the

manuals and disclaimer information for the software and cameras that are used.

Software Versions

Operation procedures and window images might vary depending on the firmware version

of the network camera, the version of the operation application, and the software version

of Vision Edition.

This manual describes operations based on the following versions.

Network camera VB-H45 1.0.0

Camera Management Tool 2.4

Vision Edition 1.2.1

Contents

Introduction ……………………………………………………………………… 02

Software Versions ……………………………………………………… 02

Chapter 2 Device Connections

Required Devices ……………………………………………………………… 22

(1) Connect the Camera and the Image Processing Controller ……… 23

Chapter 3 Vision Edition Settings

(4) Configure Capture Settings and Register a Master Image ………… 36

(5) Edit the 2D Code Recognition Unit ……………………………………… 42

Chapter 4 Operation Check

(1) Perform Debugging in Offline Mode …………………………………… 50

(2) Prepare for Online Mode ………………………………………………… 51

(3) Perform Operation in Online Mode …………………………………… 52

(4) Procedure After Completing Work …………………………………… 53

(3) Edit the Flowchart ……………………………………………………… 34

Chapter 1 Camera Settings

Required Devices ……………………………………………………………… 05

(6) Reference: Using the Camera Management Tool to Find the

Camera's IP Address ………………… ………………… ………………… 16

(2) Connect the Camera to a PC …………………………………………… 08

(3) Configure the PC Network Settings ……………………………………… 09

(4) Register a Camera Administrator, and Configure an IP Address …12

(5) Configure the PC Network Settings ……………………………………… 15

(7) Set the Camera's JPEG Compression Ratio …………………………… 18

(1) Reset the Camera to the Factory Settings …………………………… 06

(6) Configure the Display Options …………………………………………… 44

(7) Configure the Main Screen Validation Condition Settings ………… 47

(8) Configure the Camera's Video Flip Setting …………………………… 19

(1) Add a Sample JOB ………………………………………………………… 29

(2) Register the Camera ……………………………………………………… 31

Camera Settings

1. Network camera (VB-H45) 2. PoE Hub (no specific model)

* Power supply to camera required

* Hub with 2 or more ports required

3. Windows PC

* This manual uses windows from

Windows 7/10 in its

descriptions.

4. LAN cable (no specific model)

* Straight, Cat 6 or better recommended

* Minimum 2 cables required

Camera Settings

To use a Canon network camera with Vision Edition, you must configure the camera settings

in advance. This chapter describes the procedure for configuring the settings for a network

camera (VB-H45) that still has the factory default settings.

Required Devices

Make sure the following devices are available.

Quick Help

Case 1: I want to reset the camera to the factory default settings before configuring it.

→ "Proceed to (1) Reset the Camera to the Factory Settings".

Case 2: I want to configure a camera that has the factory default settings.

→ Proceed to "(2) Connect the Camera to a PC".

Case 3: I know the camera's administrator name and password, but I forgot the IP address.

→ Perform the steps in "(2) Connect the Camera to a PC" and "(5) Configure the PC

Network Settings", and then proceed to "(6) Reference: Using the Camera

Management Tool to Find the Camera's IP Address".

Case 4: I forgot the camera's administrator name and password.

→"Proceed to (1) Reset the camera to the factory settings".

Case 5: I know the camera's administrator name, password, and IP address.

→ Perform the steps in "(2) Connect the Camera to a PC" and "(5) Configure the PC

Network Settings", Proceed to "(7) Set the Camera's JPEG Compression Ratio".

* An industrial camera (N10-W02) can be used

immediately with the factory default settings.

Proceed to Chapter 2.

(1) Reset the Camera to the Factory Settings

Turn ON the power to the PoE hub, and connect one end of a LAN cable to the

power supply port on the PoE hub. Do not connect the other end of the LAN cable

to the camera yet.

Use a pointed object such as the tip of a pen to press in and hold the Reset switch.

With the Reset switch pressed in, connect the LAN cable to the network camera.

Wait about 5 seconds, and then release the Reset switch.

When the network camera's LED comes on and the camera moves slightly in the

pan and tilt directions, this setting is complete.

[For VB-H45 and VB-S30D Mk II]

The following settings will be applied when you reset the camera to the factory default

settings.

IP address: DHCP (Initial IP:192.168.100.1)

Administrator name: None

Administrator password: None

PoE hub

PoE PoE Non-PoE Non-PoE

Camera unit

Do not connect the LAN cable yet.

If you have forgotten the camera's administrator name and password, reset the camera

to the factory default settings.

Note

It might take some time for the camera's initialization process to finish (about 5 minutes).

[VB-H45] [VB-S30D Mk II]

For [N10-W02]

The following settings will be applied when you reset the camera to the factory default

settings.

IP address: 192.168.0.90

Administrator name: admin

Administrator password: password

Use a LAN cable to connect the camera to the power supply port on the PoE hub,

and turn ON the power to the PoE hub.

PoE hub

PoE PoE Non-PoE Non-PoE

Use a pointed object such as the tip of a pen to press in the Reset switch on the

back of the camera.

(2) Connect the Camera to a PC

PoE hub

Use LAN cables to connect the Windows PC and the network camera to the PoE

hub. Connect the network camera to the power supply port on the PoE hub.

* Do not connect any devices other than the camera and the Windows PC.

Otherwise, the identical IP addresses might be used.

PoE PoE Non-PoE Non-PoE

Camera unit Windows PC

Turn ON the power to the Windows PC and the PoE hub. (It is ok if they are already ON.)

Wait about 30 seconds for the camera to finish starting up. (When the network

camera's LED comes on and the camera moves slightly in the pan and tilt directions,

the startup process is complete.)

LED

(3) Configure the PC Network Settings

Open the Control Panel.

Click [Change adapter settings].

Configure the Windows PC's network settings in order to configure the network camera

settings. Change the PC's IP address to "192.168.100.100" (*).

* Although the IP address can be changed to a value that is appropriate for the

environment (192.168.100.xx: xx=1 to 254), avoid using "192.168.100.1" because that is the

default value for the network camera.

[Windows 7] [Windows 10]

Click [View network status and tasks].

[Windows 7] [Windows 10]

Select [Internet Protocol Version 4 (TCP/IPv4)], and then click [Properties].

Right-click [Local Area Connection] (win7) or [Ethernet] (win10), and select

[Properties] from the menu that is displayed.

[Windows 7] [Windows 10]

Autres manuels pour VB-H45

Table des matières

Autres manuels Canon Caméra de sécurité

Canon

Canon VB-R13 Manuel utilisateur

Canon

Canon VB-C300 Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Canon

Canon Vb-C60 - Ptz Network Camera Mode d’emploi

Canon

Canon VB-S30D MKII Manuel utilisateur

Canon

Canon ME20F-SHN Manuel utilisateur

Canon

Canon VB-H761LVE Manuel utilisateur

Canon

Canon Vb-C60 - Ptz Network Camera Manuel utilisateur

Canon

Canon VB-C50Fi Manuel utilisateur

Canon

Canon VC-C50i/VC-C50iR Manuel d'utilisation et d'entretien

Canon

Canon CAM-IPTZ-101 Manuel utilisateur

Canon

Canon VB-M600VE Manuel utilisateur

Canon

Canon VB-H43 Manuel utilisateur

Canon

Canon VB-R11 Manuel utilisateur

Canon

Canon 1064C001 Manuel utilisateur

Canon

Canon VB-H751LE Manuel utilisateur

Canon

Canon DU10-H-VB Manuel utilisateur

Canon

Canon VC-C50i Manuel utilisateur

Canon

Canon VB-R10VE Manuel utilisateur

Canon

Canon VB-M600D Manuel utilisateur

Canon

Canon VB-C50i/VB-C50iR Manuel utilisateur

Canon

Canon VB-H47 Manuel utilisateur

Canon

Canon VB-M40 Manuel utilisateur

Canon

Canon Vb-C60 - Ptz Network Camera Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur