Canon DADF-M1 Manuel de référence

(1/1)

Canon Service Bulletin COPIER

Issued by Canon Europa N.V.

Location:

DOCUMENT TRAY ASSEMBLY

Subject:

Frequent Appearance of Message Prompting to Clean ADF Scanning Glass

Detail:

The following message is displayed on the LCD of the host machine in order to prompt users to clean the ADF

scanning glass, although there is no dust on the glass.

Message:

Originals may not be scanned clearly (streaks may appear). Clean the thin glass strip as shown in the illustration

with a damp, well wrung-out cloth.

<Cause>

The starting position of the image scanning in the main scanning direction when using ADF (stream reading) is

determined by the position of the original. The dust detection area is determined with reference to the scanning

starting position. Also, the position of the original is determined by the position of the side guide plates of the

ADF.

If the side guide plates are fixed at a position where the edge of the original comes close to the edge of the platen

roller, the roller edge will come in the dust detection area and finally be detected as dust.

1. RCON software of the host machine is upgraded to Ver.8.01 so that the dust detection area is changed from

301mm to 298mm.

2. The procedure for adjusting the side guide plates of the DF is changed.

Service Work:

When the above symptom occurs, upgrade the Rcon Software of the host machine to Ver.8.01, referring to the

Service Information F2-T01-0M3-10016 (System Software information for iRC6800 series).

When the upgrade still fails to remove the symptom, see the attached procedure below and adjust the horizontal

registration as well.

Model:

DADF-M1

Ref No.:

DF-168

(F3-T01-00X-10014-01)

Date:

25-06-04

Horizontal Registration

(Prevention of Frequent ADF reading Glass Cleaning

Massage)

1. Adjusting the Side Guide Plate Position of

the ADF Original Pickup Tray

1) Place an original of A3 or 11x17 on the original

pickup tray. Press the Start key to run the machine.

2) Stop the machine forcibly when the original

passes through the platen roller by opening the

feeder cover.

3) Open the ADF, check the horizontal registration

(front: A/ rear: B) of the original [1] with reference

to the platen roller [2], and take a note of the

measurement.

Standard Measurement:

Original of A3: A=B=3.5mm

Original of 11x17: A=B=12.5mm

4) Open the feeder cover, and detach the inside

cover.

5) Remove the 3 mounting screws [1], and detach

the cover [2].

6) Loosen the mounting screw [1], and remove the

screw [2] from the positioning hole, and fit it and

temporarily tighten it in the adjusting angular hole

[3].

- if A > B, move the volume unit [4] to the front.

- if A < B, move the volume unit [4] to the rear.

Standard Measurement:

Original of A3: A=B=3.5mm

Original of 11x17: A=B=12.5mm

7) Tighten the screw [1] that has been tentatively

tightened and the screw [3] that has been fitted in

the adjusting angular hole.

8) When done, mount back the cover.

2. Making Adjustments Using the Host

Machine's Service Mode

1) Obtain the Test Chart.

If the Test Chart is not available, prepare one using

A4 or LTR paper as follows:

2) Place the Test Chart in the original pickup tray,

and make a copy at a 100% reproduction ratio.

3) Put the Test Chart over the output of step 2),

and check to see that the following is true

A</=1mm

B</=1mm

If not, go to step 4).

4) Start service mode as follows: press the User

Mode key, press the 2 and 8 keys at the same time,

and press the User Mode key once again.



5) Make the following selections:

COPIER>ADJUST>ADJ-XY>ADJ-Y-DF. Then,

change the setting to make adjustments.

- A higher setting will increase the margin of A,

decreasing the margin of B.

(in: 0.1 m)

(range: 21 to 106)

6) Make a copy of the Test Chart once again, and

check to see that the image is as indicated.

Autres manuels pour DADF-M1

Autres manuels Canon Photocopieuse

Canon

Canon NP-1010 Manuel utilisateur

Canon

Canon C5000 - MultiPASS Color Inkjet Printer Mode d’emploi

Canon

Canon IMAGERUNNER 7086 Manuel utilisateur

Canon

Canon PC720 Manuel utilisateur

Canon

Canon iR5000i Manuel utilisateur

Canon

Canon Vizcam 1000 Manuel utilisateur

Canon

Canon DADF-B1 Manuel utilisateur

Canon

Canon iR2000 Series Manuel utilisateur

Canon

Canon iMAGERUNNER 2018i Manuel utilisateur

Canon

Canon CLC5151 Manuel utilisateur

Canon

Canon imageRUNNER 1435iF Manuel utilisateur

Canon

Canon NP-70 Manuel utilisateur

Canon

Canon iR ADV C55 i Series Guide de l'administrateur

Canon

Canon NP6012F Manuel utilisateur

Canon

Canon iR5570 Series Manuel de référence

Canon

Canon imageRUNNER 1300 Series Manuel utilisateur

Canon

Canon imageRUNNER 2520 Series Manuel utilisateur

Canon

Canon imageRunner Advance 6275 Instructions de montage

Canon

Canon IMAGERUNNER 2020 Manuel utilisateur

Canon

Canon iR1210 Manuel d'utilisation et d'entretien

Canon

Canon imageRUNNER 105 Manuel d'instructions et de sécurité

Canon

Canon image RUNNER 3045 Instructions d'installation et d'entretien

Canon

Canon Color ImageRUNNER C2058 Manuel utilisateur

Canon

Canon CLC 10 Manuel utilisateur

Manuels Photocopieuse populaires d'autres marques

Ricoh

Ricoh FW740 Manuel utilisateur

Minolta

Minolta CF910 Manuel utilisateur

Ricoh

Ricoh B003 Manuel utilisateur

Xerox

Xerox EC70 Manuel utilisateur

Oce

Oce 9800 Manuel utilisateur

Olivetti

Olivetti d-Copia 1800 Manuel utilisateur

Minolta

Minolta Di181 Manuel utilisateur

Telecrane

Telecrane F25 Manuel utilisateur

Xerox

Xerox WorkCentre Pro 40 Manuel utilisateur

Sharp

Sharp AR-5015 N Manuel utilisateur

Ricoh

Ricoh Di-C1 Manuel utilisateur

Mita

Mita MIP-2400 Manuel

Sharp

Sharp AL-2061 Manuel utilisateur

Muratec

Muratec MFX-C2280 Manuel utilisateur

Ricoh

Ricoh FT5034C Manuel utilisateur

Minolta

Minolta EP4000 Manuel utilisateur

Ricoh

Ricoh V-C3 Guide d'installation

Triumph Adler

Triumph Adler DCC 2526 Manuel