C&C TECHNIC PG-V1 Manuel utilisateur
0
PATTERN
GENERATOR
PG-V1
USER MANUAL
V.2009PGV101.00
Copyright and Trademarks:
All rights reserved by C&C TECHNIC TAIWAN CO., LTD. No part of this
document may be reproduced in any form or by any means without written
permission from the product manufacturer. Changes are periodically
made to the information in this document. They will be incorporated in
subsequent editions. The product manufacturer may make improvements
and /or changes in the product described in this document at any time.
All the registered trademarks referred to this manual are belonging to their
respective companies.
1
Chapter 1 Introduction ..............................................2
1.1 Package Contents............................................2
1.2 Resolution.......................................................3
1.3 Features ..........................................................3
1.4 Specifications .................................................3
1.5 Front Panel......................................................4
1.6 Side Panel .......................................................5
1.6.1 Video Output Port................................5
1.6.2 HD-15 Connector Pin Definition.........5
1.6.3 Power Jack...........................................5
Chapter 2 Connection ...............................................6
2.1 Preparation......................................................6
2.1.1 Plugs ....................................................6
2.1.2 Plug replacement .................................6
2.2 Connect PG-V1 to Monitor ............................7
Chapter 3 Operation..................................................8
3.1 Starting Status.................................................8
3.2 Power and Battery ..........................................9
3.3 MENU Configurations .................................10
3.3.1 Tim configuration ..............................10
3.3.2 Ptn configuration ...............................10
3.3.3 Sync configuration ............................11
3.3.4 Hky (Hot key) configuration .............13
Chapter 4 Troubleshooting.....................................14
Appendix A................................................................15
Appendix B................................................................18
2
Chapter 1 Introduction
PG-V1 is a test pattern generator with VGA connector
designed to be a useful tool for the new generation of digital
monitor products. PG-V1 supports up to 20 resolutions and
34 patterns for you to test and calibrate a digital monitor.
Further, it also can improve the quality of digital monitor with
side by side comparisons. Through the friendly interface
and smart design, not only you can easy to use the PG-V1
but also you can reduce your test expenditure.
Caution
To avoid and minimize the risk of damage to PG-V1, please
pay attention to the safety instructions even though the
PG-V1 had been tested for conformance to safety
requirements and certified for international using.
Follow all instructions marked on the device during using.
Do not attempt to maintain the device by yourself, any
faults, please contact your vendor.
Provide proper ventilation and air circulation and do not
use near water.
It is better to keep it in a dry environment.
Only using the power adapter and connection cables that
are supported with the device.
After purchasing and before using the PG-V1 first time,
please charge it continuously for more than 16 hours.
It is better to charge the battery when the battery power
indicator becomes low.
The PG-V1 will save the last setting values automatically.
Do not use liquid or aerosol cleaners to clean the device.
Always unplug the power to the device before cleaning.
1.1 Package Contents
1 VGA pattern generator PG-V1
1 power adapter with DC 12V 1.25A, 4 replaceable plugs
(for USA, UK, Europe and Australia DC plugs.)
1 user manual
1 VGA 1.2M cable (HD-15 Male to Male)
All packages have been checked carefully for their
completeness and functionality before shipped. Please
contact with your vendor if any items listed as above are
missing or damaged.
3
1.2 Resolution
Use for test and calibrating VGA video equipments.
Use for test and calibrating VGA image input devices.
Use for TV/Monitor product lines.
1.3 Features
Intelligent functionality.
With 162 MHz pixel frequency.
Support total 38 timings. (up to UXGA)
Support Sync Type: H/V (TTL), SOG.
Low cost.
Single interface easily use.
Portable design, working time up to 6~8 hours by inside
Re-chargeable battery.
Auto Power-off on Battery mode.
Provide total 34 patterns, Include: Color bar, Gray, Grid,
Block…
By 16x2 Character LCD and key buttons, easily control.
1.4 Specifications
Function PG-V1
Video Output Connector 1 HD-15 Female
Select Switch 7
LCD Module:
16*2 Character Display 1
Max. Resolution 1600x1200 @ 60 Hz
Highest Pixel Frequency 162 MHz
Cable Distance 5M
Power Adapter (Min.) DC 12V 1.25A
Housing Plastic
Weight 385 g
Dimensions (LxWxH) 190x95x35 mm
4
1.5 Front Panel
1. Video Output Port: Connect to the attached Video
cable.
2. LCD Module: 16*2 Character Display.
3. Function Keys: Depend on the different operation
configuration will show you different functions of the keys.
4. “ ” Return: Return to up configuration page.
5. “ ” Power On/Off: Press at least more than 3 seconds
to power on/ff the PG-V1.
6. Power Jack: Connect to the DC 12V 1.25A power
adapter.
1. Video output port
2. LCD Module
3. Function Keys
4. Return
5. Power On/Off
6. Power Jack 2.0ψ
5
1.6 Side Panel
1.6.1 Video Output Port
Use for Video cable connector.
1.6.2 HD-15 Connector Pin Definition
Pin # Signal Pin # Signal
1 Red video 11 NC
2 Green video 12 NC
3 Blue video 13 Horizontal sync
4 NC 14 Vertical sync
5 Ground 15 NC
6 Analog ground
7 Analog ground
8 Analog ground
9 NC
10 Ground
1.6.3 Power Jack
Use for the DC 12V 1.25A power adapter. The Power Jack
is on the right side of the device. PG-V1 supports 4
replaceable plugs (for USA, UK, Europe and Australia DC
plugs.)
Power Jack
6
Chapter 2 Connection
2.1 Preparation
Caution
Please power off the digital monitor and PG-V1 before you
begin the connection
2.1.1 Plugs
PG-V1 supports you up to 4 replaceable plugs (for USA, UK,
Europe and Australia DC plugs.). Please depend on where
the location is to exchange the suitable plug.
US Plug UK Plug AU Plug EU plug
2.1.2 Plug replacement
PG-V1 supports a power adapter DC 12V 1.25A with a
plastic ring to protect the connector. Before you to connect
the adapter, you have to dismantle the plastic ring firstly.
Refer to the pictures as below to dismantle the plastic ring.
Caution
Please also to pull down the slider to exchange the suitable
plug.
7
2.2 Connect PG-V1 to Monitor
Connect the attached DC adapter cable from PG-V1 to
the power source (outlet).
Connect the VGA cable from PG-V1 to the Monitor/TV.
Power on the Monitor/TV.
Press the power key of PG-V1 for more than 3 seconds to
power on/off the PG-V1.
Caution
Please power off the Monitor/TV before begin the
connection.
Cable
or Twins pair
Monitor
/
TV
8
Chapter 3 Operation
)1. After pressing the power On/Off key for 2~3 seconds
to sound a long “beep”.
2. Only for the valid key of PG-V1 will sound a short
confirmed “beep” after pressing the key.
3. The chosen option will blink.
3.1 Starting Status
After you pressing the Power key to power on the PG-V1,
the LCD screen will show you the PG-V1 version suddenly
then show you the main screen as below (or previous
setting values saved in the PG-V1’s memory):
P01 640x480 @60
P01: Pattern 01 (refer to Appendix B: Pattern chart)
640x480: Resolution is 640X480
@60: Refresh rate is 60Hz
“”: The power of battery is charging.
To the LCD screen lower left will show you the PG-V1
operated mode just as SOG
SOG: Process PG-V1 under SOG mode.
H/V: Process PG-V1 under H/V mode.
.
9
3.2 Power and Battery
The device is suited to the DC 12V 1.25A power adapter
and 4 inside Re-chargeable batteries. The signals of
PG-V1’s battery on the lower right are described as below:
“”: The power of battery is charging.
“”: The power of battery is in full charging.
“”: The battery is fault.
)1. When the device stands by for about 39 minutes, it
will sound two short “beep”. After the two short
“beep” sounds about 1 minute, the device will sound a
long “beep” and shout down automatically.
2. When the battery power is lower than 5% just as “ ”,
a warming sound “beep” will be heard each second.
The sound will continue for 5 minutes, if you don’t get
the external power to instead of the internal battery
power. The device will shout down immediately. We
suggest you it is better to charge the batteries when
they are in the lower status. (Before the device shout
down, the device will save the last set values
including Pattern No., Resolution, Ver. Frequency,
P02 Blinking_BLK&WHT No. and Sync_MODE
automatically.)
Table des matières
Autres manuels C&C TECHNIC Équipement de test
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
