Campbell 10162 Manuel utilisateur

INSTRUCTION MANUAL

10162 Enclosure

Relative Humidity Sensor

Revision: 3/01

Campbell Scientific, Inc.

Warranty and Assistance

The 10162 ENCLOSURE RELATIVE HUMIDITY SENSOR is warranted

by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and

workmanship under normal use and service for twelve (12) months from date of

shipment unless specified otherwise. Batteries have no warranty. CAMPBELL

SCIENTIFIC, INC.'s obligation under this warranty is limited to repairing or

replacing (at CAMPBELL SCIENTIFIC, INC.'s option) defective products.

The customer shall assume all costs of removing, reinstalling, and shipping

defective products to CAMPBELL SCIENTIFIC, INC. CAMPBELL

SCIENTIFIC, INC. will return such products by surface carrier prepaid. This

warranty shall not apply to any CAMPBELL SCIENTIFIC, INC. products

which have been subjected to modification, misuse, neglect, accidents of

nature, or shipping damage. This warranty is in lieu of all other warranties,

expressed or implied, including warranties of merchantability or fitness for a

particular purpose. CAMPBELL SCIENTIFIC, INC. is not liable for special,

indirect, incidental, or consequential damages.

Products may not be returned without prior authorization. The following

contact information is for US and International customers residing in countries

served by Campbell Scientific, Inc. directly. Affiliate companies handle repairs

for customers within their territories. Please visit www.campbellsci.com to

determine which Campbell Scientific company serves your country. To obtain

a Returned Materials Authorization (RMA), contact CAMPBELL

SCIENTIFIC, INC., phone (435) 753-2342. After an applications engineer

determines the nature of the problem, an RMA number will be issued. Please

write this number clearly on the outside of the shipping container.

CAMPBELL SCIENTIFIC's shipping address is:

CAMPBELL SCIENTIFIC, INC.

RMA#_____

815 West 1800 North

Logan, Utah 84321-1784

CAMPBELL SCIENTIFIC, INC. does not accept collect calls.

10162 Table of Contents

PDF viewers note: These page numbers refer to the printed version of this document. Use

the Adobe Acrobat® bookmarks tab for links to specific sections.

1. General........................................................................1

2. Specifications .............................................................1

3. Installation...................................................................1

4. Wiring ..........................................................................2

5. Example Programs .....................................................2

6. Enclosure Humidity....................................................4

7. Maintenance................................................................4

This is a blank page.

10162 Enclosure Humidity Sensor

1. General

The 10162 Enclosure Humidity sensor contains a Elan HM2000 series precision

bulkpolymer relative humidity sensor. It is used to monitor the relative humidity

inside an equipment enclosure deployed in the field.

2. Specifications

Sensor: Elan HM2000 series precision bulkpolymer

Relative Humidity Measurement Range: 0 to 100% non-condensing

RH Output Signal Range: 0 to 1.0 VDC

Accuracy at 25°C

unspecified (0 to 10% Relative Humidity)

±3% RH (10 to 90% Relative Humidity)

unspecified (90 to 100% Relative Humidity)

Typical Long Term Stability: Better than 3% RH per year

Response Time (at 25°C, 90% response): 1.5 minutes for a 30% to 90% RH

step change

Operating Temperature: 0°C to +50°C

Storage Temperature: -40°C to +80°C

Probe Length: 2.6 cm (1.02 in.)

Probe Cross Section Area: 0.6 cm x 1.1 cm (0.23 in. x 0.43 in.)

Power Consumption: <0.5 mA

Supply Voltage: 5 ±0.25 VDC

Settling Time: 3 minutes

3. Installation

Mount the 10162 inside the environmental enclosure using the mounting block

and the wire tie included with the sensor (Figure 1).

The black outer jacket of the cable is Santoprene® rubber. This

compound was chosen for its resistance to temperature extremes,

moisture, and UV degradation. However, this jacket will support

combustion in air. It is rated as slow burning when tested

according to U.L. 94 H.B. and will pass FMVSS302. Local fire

codes may preclude its use inside buildings.

NOTE

10162 Enclosure Humidity Sensor

CAMPBELL

SCIENTIFIC

INC.

AG HL

AG E3 AG GG

AG HL

AG E3 AG GG

DEF

789101112

123456

EARTH

G5V P1 C8

5V P2 C7 C6 C5 C4 C3 C2 C1

SWITHCED

12V

CONTROL

GGGG12V 12V

SWITHCED

12V

CR10

MADE IN USA

WIRING PANEL NO.

SERIALI/O

Clear

Black-5V OR CONTROL

White-SINGLE END

FIGURE 1. 10162 Wiring and Installation

TABLE 1. Datalogger Connections

Description Color CR10(X), CR500,

CR23X

21X, CR7

Relative Humidity White Single-Ended Input Single-Ended Input

Signal & Power

Reference

Clear G

Power Black 5 V Control Port

4. Wiring

Connections to Campbell Scientific dataloggers are given in Table 1. The

probe is measured by a single-ended analog input channel.

5. Example Programs

This section is for users who write their own datalogger programs. A

datalogger program to measure this sensor can be created using Campbell

Scientific’s Short Cut Program Builder Software. You do not need to read this

section to use Short Cut.

The relative humidity signal from the 10162 is measured using a single-ended

analog measurement (Instruction 1).

The probe output scale is 0 to 1000 millivolts for the relative humidity range of

0 to 100%. Table 2 provides calibration information for relative humidity.

Clear Signal & Power Reference

Black 5 VDC Power

White Signal

10162 Enclosure Humidity Sensor

TABLE 2. Calibration for

Relative Humidity

Units Multiplier

(% mV-1)

Offset

(%)

Percent 0.1 0

TABLE 3. Wiring for Example 1

Description Color CR10(X)

Relative Humidity White SE 6 (3L)

Signal & Power Reference Clear G

Power Black 5 VDC

Example 1. Sample CR10(X) Program

;Measure the 10162 relative humidity.

;

01: Volt (SE) (P1)

1: 1 Reps

2: 5 2500 mV Slow Range ;CR510 (2500 mV); CR23X (1000 mV)

3: 6 SE Channel ;White wire (SE 6), Clear wire (G)

4: 3 Loc [ RH_enc ]

5: .1 Mult

6: 0 Offset

TABLE 4. Wiring for Example 2

Description Color 21X

Relative Humidity White SE 9 (5H)

Signal & Power Reference Clear GND

Power Black C1

Example 2. Sample 21X Program

;Turn the 10162 probe on and leave it on.

;

01: Do (P86)

1: 41 Set Port 1 High ;Black wire (C1)

;Measure the 10162 relative humidity.

;

02: Volt (SE) (P1)

1: 1 Reps

2: 5 5000 mV Slow Range ;CR10(X),CR510 (2500 mV); CR23X

(1000 mV); CR7 (1500 mV)

3: 9 SE Channel ;White wire (SE 9), Clear wire (GND)

4: 1 Loc [ RH_enc ]

5: .1 Mult

6: 0 Offset

10162 Enclosure Humidity Sensor

6. Enclosure Humidity

Change the enclosure desiccant packs (model number DSC 20/4) when the

enclosure relative humidity exceeds 35%.

Campbell Scientific recommends that all cable entry ports, that do not use a

sealed bulkhead connector, be sealed with plumbers putty and that desiccant

packs be placed inside the enclosure. Spikes in the enclosure humidity are a

result of opening the enclosure door and allowing ambient air inside the

enclosure. The enclosure relative humidity will return its nominal values

(values before the enclosure door was opened) in approximately three to four

hours.

7. Maintenance

The 10162 does not have any user serviceable parts nor does it require any

routine maintenance.

Replace the 10162 probe every three to five years of continuous use. If the

probe fails, replace it with a new one.

This is a blank page.

Campbell Scientific Companies

Campbell Scientific, Inc. (CSI)

815 West 1800 North

Logan, Utah 84321

UNITED STATES

www.campbellsci.com

info@campbellsci.com

Campbell Scientific Africa Pty. Ltd. (CSAf)

PO Box 2450

Somerset West 7129

SOUTH AFRICA

www.csafrica.co.za

[email protected]

Campbell Scientific Australia Pty. Ltd. (CSA)

PO Box 444

Thuringowa Central

QLD 4812 AUSTRALIA

www.campbellsci.com.au

[email protected]m.au

Campbell Scientific do Brazil Ltda. (CSB)

Rua Luisa Crapsi Orsi, 15 Butantã

CEP: 005543-000 São Paulo SP BRAZIL

www.campbellsci.com.br

suporte@campbellsci.com.br

Campbell Scientific Canada Corp. (CSC)

11564 - 149th Street NW

Edmonton, Alberta T5M 1W7

CANADA

www.campbellsci.ca

dataloggers@campbellsci.ca

Campbell Scientific Ltd. (CSL)

Campbell Park

80 Hathern Road

Shepshed, Loughborough LE12 9GX

UNITED KINGDOM

www.campbellsci.co.uk

[email protected]k

Campbell Scientific Ltd. (France)

Miniparc du Verger - Bat. H

1, rue de Terre Neuve - Les Ulis

91967 COURTABOEUF CEDEX

FRANCE

www.campbellsci.fr

campbell.scientifi[email protected]r

Campbell Scientific Spain, S. L.

Psg. Font 14, local 8

08013 Barcelona

SPAIN

www.campbellsci.es

info@campbellsci.es

Please visit www.campbellsci.com to obtain contact information for your local US or International representative.

Table des matières

Autres manuels Campbell Accessoires

Campbell

Campbell DustVue Manuel utilisateur

Campbell

Campbell SR50A Series Manuel utilisateur

Campbell

Campbell 05103 Manuel utilisateur

Campbell

Campbell SDM-CD16D Manuel utilisateur

Campbell

Campbell EE181 Manuel utilisateur

Campbell

Campbell CS230 Manuel utilisateur

Campbell

Campbell ICEFREE3A Manuel utilisateur

Campbell

Campbell CS250DM Manuel utilisateur

Campbell

Campbell SoilVUE 10 Manuel utilisateur

Campbell

Campbell ClariVUE 10 Manuel utilisateur

Campbell

Campbell SR50 Manuel utilisateur

Campbell

Campbell HMP155A Manuel utilisateur

Campbell

Campbell CS100 Manuel utilisateur

Campbell

Campbell HFP01 Manuel utilisateur

Campbell

Campbell RainVUE SDI-12 Series Manuel utilisateur

Campbell

Campbell CS105 Manuel utilisateur

Campbell

Campbell SDM-CVO4 Manuel du propriétaire

Campbell

Campbell Met One 014A Manuel utilisateur

Campbell

Campbell CRS451 Manuel utilisateur

Campbell

Campbell 255-100 Manuel utilisateur

Campbell

Campbell CS506 Manuel utilisateur

Campbell

Campbell SkyVUE Pro Manuel utilisateur

Campbell

Campbell HFT3 Manuel utilisateur

Campbell

Campbell SR50A Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur