CAME ZLX24S Manuel utilisateur

FA01797-EN

88006-0085

EN English

CAME S.p.A.

Via Martiri della

Libertà, 15

31030 Dosson di Casier

Treviso - Italy

Tel. (+39) 0422 4940

Fax (+39) 0422 4941

[email protected] -

www.came.com

DESCRIPTION OF PARTS

KIT components

1Control board ZLX24S (801QA-

0060 / 801QA-0080)

2Control board holder

3Terminal block with fuse

compartment

4Fuse 4 A (line 120 V)

5Fuse 3.15 A (line 230 V)

6Two 2-pole terminal blocks

FA01797-EN - 05/2022

88006-0085

2- Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Description of control board components

1Accessories fuse

2Control board fuse

3Terminal board for power supply to the control board

4Terminal board for connecting the signalling devices

5Terminal board for connecting control devices

6Display

7Terminal board for connecting the safety devices

8Memory Roll card connector

9Terminal board for B1-B2 output

10 Connector for CAME KEY*

11 RIO CONN card connector*

12 Terminal board for CRP connection**

13 RSE card connector**

14 Terminal board for connecting the antenna

15 Connector for plug-in radio frequency card (AF)

Use only AF43S or AF868 with diagram number DIS29101 or

above.

16 Programming buttons

17 Terminal board for BUS devices*

18 Terminal boards for connecting micro limit switches and/or encoders

19 Terminal board for connecting the gearmotor with encoder or with

slowdown switch and electric lock

(*) Cannot be used

(**) Not suitable for spare part ZL19N

3- Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

INSTALLATION

AControl board support ﬁxing point

BFuse holder terminal block ﬁxing point

Screws not provided. Reuse the screws in the ZL19N or ZLJ24

control panel.

4- Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

ELECTRICAL CONNECTIONS

Before working on the control panel, cut o the mains power supply.

Always insert the line fuse in the terminal block.

5- Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

ZLJ24 control panel

①Blue cable

②White cable

③Red cable

④Black cable

⑤Orange cable

⑥Purple cable

120 / 230 V AC

ZLJ24

L1T L2T

24 12 0

THERMALS

L N

24 12 0

L1T L2T

6- Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

②White cable

④Black cable

⑤Orange cable

⑥Purple cable

Cable not provided

ZLX24

120 / 230 V AC

7- Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

ZL19N control panel

①Blue cable

②White cable

③Red cable

④Black cable

⑤Orange cable

⑥Purple cable

⑦Brown cable

⑧Blue cable

L1T L2T

THERMAL PROT

120 / 230 V AC

L N

ZL19N

8- Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

②White cable

④Black cable

⑤Orange cable

⑥Purple cable

Cable not provided

ZLX24

120 / 230 V AC

9- Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Maximum capacity of contacts

The total power of the outputs listed below must not exceed the maximum output power [Accessories]

Device Output Power supply (V) Maximum power (W)

Accessories 10 - 11 26 AC 20

Additional light 10 - E3 26 AC 10

Flashing beacon 10 - E 26 AC 10

Operator status warning light 10 - 5 26 AC 3

The outputs deliver 24 V DC when the batteries start operating, if they are installed.

Device Output Power supply (V) Power (W)

Auxiliary contact B1 - B2 - 24 (24V AC/DC)

Connecting gearmotors without R interface (control board 119RIR267)

Connection with slowdown microswitch Connection with limit-switch/slowdown microswitch

FC1 FA1 F FC2 FA2 F

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

M1 M2

FC1 FA1 F FC2 FA2 F

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

M1 M2

Set the function [F72 - Limit-switch function] taking into account the chosen connection.

10 - Manual FA01797-EN - 05/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Command and control devices

1STOP button (NC contact)