Calix E7-2 Guide de l'utilisateur

E7-2/E5-48/E3-48C R2.4

xDSL Applications Guide

December 2015

#220-00811, Rev 12

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Contents

About This Guide......................................................................5

Chapter 1: VDSL Applications Overview...............................9

xDSL Subscriber Access Support .........................................................................10

Modular Chassis Deployment ................................................................................16

Chapter 2: Configuring VDSL2 Applications ......................19

Step 1. Configuring the Network Uplink(s) for VDSL2 Services..........................20

Overview: Configuring the Network Uplink(s) .................................................20

Configuring the Ethernet Uplink Port...............................................................21

Configuring an Ethernet Interface...................................................................26

Configuring a Link Aggregation Interface........................................................33

Creating the Service VLAN(s).........................................................................47

Additional multicast addressing considerations ..............................................50

Adding the Uplink Interface(s) to VLAN Memberships....................................64

Step 2. Creating VDSL2-Related Profiles...............................................................68

Overview of VDSL2-Related Profiles..............................................................68

Creating the Quality of Service for VDSL2 Traffic Management.....................71

Creating Data and Video Service Profiles.....................................................105

Creating Voice Service Profiles ....................................................................155

Step 3. Configure Subscriber Services................................................................177

Configuring Data Services............................................................................177

Configuring IP Video Services......................................................................189

Configuring Voice Services...........................................................................201

Configuring T1/E1 PWE3 Services...............................................................213

xDSL Port Power Save.................................................................................213

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Chapter 3: Reference Information......................................215

System Support Capacities..................................................................................216

xDSL Support Capacities......................................................................................221

E-Series LED Behavior..........................................................................................223

E-Series Line Card Additional Status Descriptions............................................225

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

About This Guide

This Calix E7, E3-48, E5-48 and E5-48C Ethernet service access platforms leverage VDSL2

and ADSL2+ technology, along with an Ethernet switching fabric, to perform L2

aggregation / switching and layer-3-aware service delivery.

The Calix topics in this guide describe how to configure VDSL2-based services for the

following platforms:

E7-2 in stand-alone and modular chassis configurations

E5-48, E5-48C and E3-48C in stand-alone configurations

Note: Calix E7-20 products do not support VDSL2-based cards or services.

Throughout this guide, E-Series is used to refer to the specific product of E7-2 that supports

VDSL2 cards and the E3-48C, E5-48 and E5-48C products that supports the equivalent of

the VDSL2 line cards.

For specific procedures on provisioning Ethernet elements, such as VLANs, Ethernet ports

and interfaces on the E5-48, E5-48C and E3-48C, refer to the Calix E3-48/E5-48/E5-48C

User Guide.

Intended Audience

This document is intended for use by network planning engineers, CO technicians, and craft

and support personnel responsible for network equipment turn-up, service configuration,

and maintenance. The procedures in this guide are of a technical nature and should only be

performed by qualified personnel. Familiarity with standard telecom and datacom

terminology and practices, as well as standards-based Ethernet technologies and conventions,

is recommended.

Related Documentation

You can access Calix product documentation from the Calix Resource Center online at

www.calix.com (https://www.calix.com/portal/site/resourcecenter/).

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

The Calix E7 documentation set includes:

Engineering and Planning

Calix Ethernet Access Networks Engineering & Planning Guide

This document provides high-level engineering and planning information for

building secure, reliable, resilient, and scalable Layer 2 switched Ethernet

access networks using Calix products to deliver data, voice, and video services.

It describes all aspects of Ethernet access network design—from physical

topologies to network bandwidth requirements in the context of Calix

products, describing an access network where the traffic terminates at the edge

router.

Calix E7 Engineering and Planning Guide

This document provides engineering and planning information for the Calix

E7 Ethernet Service Access Platform (ESAP) and Calix E3-48C Ethernet

Service Access Node (ESAN). It describes the features and capabilities of each

system, and provides engineering guidelines to assist engineers and network

planners effectively deploy the E7 and E3-48C.

Installation

Calix E7-2 Installation Guide

Calix E7-20 Installation Guide

Calix E3-48C Installation Guide

Calix E5-48/E5-48C Installation Guide

These documents provide a general installation practice for the Calix Ethernet

service access platform, including guidance for planning, power installation,

cabling, and maintenance.

User Guide

Calix E7 User Guide

Calix E3-48C, E5-48/E5-48C R2.3 User Guide

These guides are intended for initial turnup and also show you how to set up

management access, system attributes, administrative tasks, and configure

transport and aggregation applications.

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Software Upgrade

Calix E7/E5-48/E3-48C System Upgrade Guide

This document describes how to perform software/firmware upgrades as well

as database backup and restore operations.

Calix E7 GPON ONT Upgrade Guide

For E7 GPON systems, this document describes how to perform upgrades for

compatible P-Series, GigaCenter, and T-Series GPON ONTs.

Application Provisioning

Calix E7 GPON Applications Guide

Calix E7-2/E5-48/E3-48C xDSL Applications Guide

Calix E7 Active Ethernet Applications Guide

These application guides show you how to provision subscriber services using

specific technologies, assuming that the system is already installed and turned

up.

Maintenance and Troubleshooting

Calix E7 Maintenance and Troubleshooting Guide

This guide includes procedures for monitoring E7 network operation, general

troubleshooting, and replacing or installing equipment.

Command Line Interface

Calix E3-48C, E5-48/E5-48C CLI Reference

This document provides a comprehensive command reference for the E-series

Command-Line Interface (CLI) and describes how to perform key system

management and operational functions from the CLI. The embedded

command-

line interface (CLI) for system management access can be used over

local or remote TCP/IP connections and local console connections.

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Related Documentation

P-Series/T-Series ONT Software Matrix for E7 GPON

Calix P-Series ONT Model/Feature Matrix

Calix 800G GigaCenter Embedded Web Interface (EWI) User's Guide

Calix T1 Pseudowire Applications Guide

Calix C7 VoIP Services Guide

Calix Application Note: Using the ONT VoIP Configuration File

Completing Residential Gateway and SIP Configuration File Intake Forms

Calix P-Series VoIP Configuration File - Template

Calix 836GE RSG Wi-Fi Best Practices Guide

Calix GPON RF Overlay Deployment Guidelines

Calix Application Note: GPON Interface Adaptor

Calix E7 Pluggable Transceiver Module Support

CAB-12-023 - Pairing Bidirectional SFPs (to Support Single-Fiber Ethernet Links)

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Chapter 1

VDSL Applications Overview

This chapter describes VDSL2 applications and the Calix E-Series VDSL2 solution.

Topics Covered

This chapter covers the following topics:

An overview of the E-Series xDSL support

Description of modular chassis deployment with VDSL-based cards

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

xDSL Subscriber Access Support

The Calix E-Series Ethernet service platform leverages VDSL2 and ADSL2+ technology,

along with an Ethernet switching fabric, to perform L2 aggregation / switching and layer-3-

aware service delivery. Up to two dedicated 10 Gigabit and four 2.5 or 1 Gigabit Ethernet

uplinks can be leveraged to provide high capacity service delivery on a per-chassis basis.

E7-2 VDSL2-48 Overlay Line Card

Interfaces:

48x DSL Overlay ports with corresponding 600- or 900-Ohm integrated splitters

Four 1GE / 2.5GE SFP MSA sockets, and two 1GE / 10GE SFP+ MSA sockets

Features:

The VDSL2-48 also supports pair bonding in both ADSL2+ and VDSL2 modes.

One VDSL2-48 line card can be installed in an E7-2 chassis.

Integrated splitters provide a means to extract analog voice form the service loop and

terminate it on an existing DLC or analog POTS port on a switch line bay. One E7-2

VDSL2-48 line card can be plugged into a Calix E7-2 shelf to create a compact, high

density DSL overlay node, with Ethernet aggregation and transport, ideal for copper

based delivery of IP services leveraging existing POTS infrastructure, across the access

network.

Rev 13 and above of the VDSL2-48 card supports 600/900 Ω impedance, compatible

with all E7 releases. There is no need to select between 600 and 900 Ω impedance and

the splitter design accommodates either impedance without configuration.

POTS interfaces of the VDSL2-48 line card have the following characteristics:

Impedance of 600 Ω + 2.16 μf, supporting ETSI based loop plants

Impedance of 900 Ω + 2.16 μf, supporting ANSI based loop plants

Loop current of up to 25mA (during normal operation), and 18mA (during battery

backup)

E7-2 VDSL2-48 r2 Overlay Line Card

This card is backward compatible with the original E7-2 VDSL2-48 Overlay line card.

E7-2 VDSL2-48C Combo Line Card

Interfaces:

48x Combo DSL and POTS ports, two 1GE / 2.5GE SFP MSA sockets

Two 1GE/10GE SFP+ MSA sockets

Autres manuels pour E7-2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Calix Point d'accès sans fil

Calix

Calix E7-2 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur