Cabletron Systems E1100 Series Manuel utilisateur
E1100, E2100, AND E3100 SERIES
ETHERNET NETWORK ADAPTERS
INSTALLATION GUIDE
Desktop Network Interface Products
C A B L E T R O N S Y S T E M S, I N C.
NOTICE
i
NOTICE
Cabletron Systems reserves the right to make changes in
specifications and other information contained in this document
without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is
subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR
ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL
DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO
LOST PROFITS) ARISING OUT OF OR RELATED TO THIS
MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF
CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR
SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH
DAMAGES.
Copyright October 1992
Cabletron Systems, Inc.
35 Industrial Way, P.O. Box 5005
Rochester, NH 03867-0505
All Rights Reserved
Printed in the United States of America
Order number: 9030445-02 October 92
Multi Media Access Center,LANVIEW and Remote LANVIEW are
registered trademarks and Desktop Network Interface, E1100,E2100,
E3100,FOT-F,LAN-MD,and MMAC are trademarks of Cabletron
Systems, Inc.
SunNet Manager is a registered trademark of Sun Microsystems, Inc.
IBM,IBM Personal Computer AT,Micro Channel,IBM Personal
System/2 and PS/2 are registered trademarks of International
Business Machines Corporation. IBM Personal Computer XT and PC
LAN are trademarks of International Business Machines Corporation.
MS-DOS is a trademark of Microsoft Corporation.
Novell and NetWare are registered trademarks of Novell, Inc.
FCC NOTICE
ii
FCC NOTICE
This device complies with Part 15 of FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment uses, generates, and can
radiate radio frequency energy and if not installed in accordance with
the operator’s manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause interference in which case the user will be required at
his own expense to correct the interference.
If this equipment does cause interference to radio or television, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Re-orient the receiving antenna.
• Relocate the computer with respect to the antenna.
• Move the computer away from the receiver.
• Plug the computer into a different outlet so that the computer
and the receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced
radio/television technician for additional suggestions. The user may
find the following booklet prepared by the Federal Communication
Commission helpful:
“Interference Handbook”
This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402 - Stock No. 004-000-00482-5.
CONTENTS
iii
CONTENTS
CHAPTER 1 INTRODUCTION
1.1 Using This Manual ....................................................................1-1
1.2 The Adapter Features ...............................................................1-2
1.2.1 Connectivity ...................................................................1-2
1.2.2 Thin Ethernet Port .........................................................1-2
1.2.3 10BASE-T Twisted Pair Port ........................................1-2
1.2.4 Fiber Optic Ports ............................................................1-3
1.2.5 Jabber Protection............................................................1-3
1.2.6 LANVIEW LEDs ............................................................1-3
1.2.7 Software ..........................................................................1-5
1.2.8 Statistics...........................................................................1-5
1.3 Related Manuals ........................................................................1-5
CHAPTER 2 INSTALLATION
2.1 Adapter Models.........................................................................2-1
2.1.1 Model Number References...........................................2-2
2.2 The E1100/E2100 Series Adapters ..........................................2-2
2.2.1 Unpacking the Adapter ................................................2-3
2.2.2 Copying the Software....................................................2-3
2.2.3 Preparing the E1100 for Installation............................2-3
2.2.4 Preparing the E2100 for Installation............................2-4
2.3 Setting the I/O Base Address Jumper ....................................2-5
2.4 I/O Address Space Requirements ..........................................2-6
2.5 Installing a Boot PROM ............................................................2-6
2.6 Installing the E1100/E2100 Adapters.....................................2-7
2.7 Installing the E3100 Series Adapters ....................................2-10
2.7.1 Preparing the E3100 Series for Installation ..............2-10
2.7.2 E3100 Series Boot PROM ............................................2-10
2.7.3 Installing the E3100 Adapter ......................................2-11
2.8 Copying the ADF File .............................................................2-14
2.9 Loading Network Software ...................................................2-14
2.10 Troubleshooting Check List for Adapters ...........................2-15
iv
CONTENTS
2.11 Software Check List ................................................................2-15
2.12 Getting Help ............................................................................2-16
2.13 Specifications ...........................................................................2-18
2.13.1 Power Requirements ...................................................2-18
2.13.2 Environmental Requirements ....................................2-18
2.13.3 Safety .............................................................................2-18
2.13.4 Dimensions ...................................................................2-18
CHAPTER 3 MAKING NETWORK CONNECTIONS
3.1 Connecting to a Twisted Pair Segment ..................................3-1
3.1.1 RJ-45 Interface (UTP Port) ............................................3-1
3.1.2 Twisted Pair Requirements ..........................................3-3
3.2 Connecting to a Thin-net Segment .........................................3-4
3.2.1 BNC Interface (Coax Port) ............................................3-4
3.2.2 Thin-Net Requirements ................................................3-5
3.3 Connecting to a Fiber Optic Link Segment............................3-6
3.3.1 Fiber Optic Requirements.............................................3-7
3.3.2 Fiber Optic Interface (Fiber Optic Ports) ....................3-8
3.4 Connecting to an External Transceiver ..................................3-9
3.4.1 AUI Connector (AUI Ports) ..........................................3-9
3.4.2 AUI Interface ................................................................3-10
3.4.3 AUI Cable Requirements ............................................3-10
APPENDIX A ADDRESS/INTERRUPT TABLES
INDEX
INTRODUCTION
Page 1-1
CHAPTER 1
INTRODUCTION
This manual provides installation and reference information for
the network adapters. The network adapters connect your PC to: a
10BASE-T twisted pair Ethernet network segment, a thin Ethernet
10BASE-2 coaxial network, a fiber optic network segment, or a
transceiver via an AUI cable.
The adapters incorporate Cabletron Systems’ LANVIEWLEDs.
These diagnostic LEDs indicate power, network transmit and
receive, link established, and collision present conditions as soon
as the adapter is connected to the network segment.
1.1 USING THIS MANUAL
This manual is organized so that you can follow sequential
chapters as you install the adapter. Read Chapter 1 first to
familiarize yourself with the adapter’s capabilities. Then:
• Copy the software diskettes supplied with the adapter.
• Install the adapters as outlined in Chapter 2.
• Run the diagnostic program supplied with the adapter.
• Connect the adapter to the network as outlined in Chapter 3.
• Install the network drivers required for your application as
outlined in the Network Software Installation Guide.
Chapter 1, Introduction, discusses the capabilities of the adapters.
Chapter 2, Installation, provides instructions for installing the
adapters in your computer.
Chapter 3, Making Network Connections, provides instructions
and requirements for connecting your adapters to the network.
INTRODUCTION
Page 1-2
1.2 THE ADAPTER FEATURES
The following sections outline the features of the adapters.
1.2.1 Connectivity
The Cabletron Systems adapters connect your computer to an
IEEE 802.3 Ethernet network. The various adapter models
incorporate either an Ethernet 10BASE-T twisted pair port, a thin
Ethernet coaxial BNC port, an SMT type fiber optic port, or an
external transceiver via an AUI cable. All port types provide
access for SNMP network management such as Cabletron’s
SPECTRUM, Remote LANVIEW/Windows, or any SNMP-
compliant management software.
1.2.2 Thin Ethernet Port
The adapter’s 10BASE-2 port provides a thin Ethernet BNC
connection to a coaxial segment such as the backbone of a
corporate-wide network, or to a concentrator such as Cabletron’s
MMAC Multi Media Access Center.
1.2.3 10BASE-T Twisted Pair Port
The adapter’s 10BASE-T twisted pair port employs the RJ-45
eight-pin industry standard connector which must be connected
to a concentrator such as Cabletron’s MMAC Multi Media Access
Center. The 10BASE-T twisted pair port on the adapter has built-
in automatic polarity detection and correction. This means that if
the cable connected to the twisted pair port should have the RX+
and RX– leads reversed, the port circuitry will automatically
detect and correct this problem.
When polarity correction has occurred, the link LED flashes to
indicate that this automatic correction has been performed.
Performance will not be impacted.
INTRODUCTION
Page 1-3
1.2.4 Fiber Optic Ports
The fiber optic ports on the adapter employs two ST type fiber
optic connectors. The dark gray ST connector is the fiber optic
receive port and light gray ST connector is the fiber optic transmit
port. The ST connector fiber optic ports can utilize
50/125 µm, 62.5/125 µm, and 100/140 µm fiber optic cables.
1.2.5 Jabber Protection
A built-in jabber protection scheme ensures that the network is
not disabled due to the transmission of excessively long packets
(jabber). This protection scheme automatically interrupts the port
for 96 bit times (1 bit time = 100 ns.) if the port has been
transmitting continuously for more than 65,536 bit times.
1.2.6 LANVIEW LEDs
Cabletron Systems’ adapters incorporate Cabletron Systems’
LANVIEW Status Monitoring and Diagnostic System. The
LANVIEW LEDs help you diagnose problems, such as failure to
establish a twisted pair link between the adapter and an Ethernet
device at the far end of the link. Individual LEDs advise you when
the adapter is receiving or transmitting data packets, or when a
collision condition exists on the network (see Figure 1-1).
• Media Link Good (LNK) LED fiber optic adapters
When lit, this green LED indicates that a link has been established
between the fiber optic port on the adapter and the fiber optic
device at the other end of the fiber optic link segment. This LED
remains lit as long as the link is maintained.
•Link OK (LNK) 10BASE-T only
When lit, this LED indicates that a link has been established
between the adapter and the device at the other end of the
Ethernet segment (green indicator).
INTRODUCTION
Page 1-4
XMT
RCV
CP
LNK or
PWR
Dual Media Adapter Dual Port Adapter
XMT
RCV
CP
LNK
LNK
Upper Po
rt
Lower Por
t
RJ-45 Port RJ-45 Port
RJ-45 Port
BNC Port
Figure 1-1. LANVIEW LEDs
•Collision Present (CLN)
This LED flashes when the adapter is transmitting to indicate that
the adapter is detecting a collision condition on the network (red
indicator).
•Receive (RCV) network traffic
This LED flashes to indicate that the adapter is receiving data
packets from the network (yellow indicator).
•Transmit (XMT)
This LED flashes to indicate the adapter is transmitting packets
onto the network (green indicator).
INTRODUCTION
Page 1-5
1.2.7 Software
Software drivers, related software, and diagnostics are supplied
by Cabletron Systems on floppy diskettes shipped with the
adapter. The drivers support a variety of network platforms. Refer
to the Network Software Installation Guide.
The diagnostic program provided with the adapter allows you to
check the adapter’s operation at various levels, through a series of
tests. The diagnostic program allows you to detect where a
problem might be located in the operation of the adapter, or
determine if a problem exists in the communication between the
adapter and the computer.
1.2.8 Statistics
Statistics can be gathered from the adapter either from your
computer, or from another workstation utilizing Cabletron
Systems’ SPECTRUM, Remote LANVIEW/Windows, Remote
LANVIEW for SunNet Manager, or other SNMP-compliant
network management software. Through this software, you can
gather statistics on the adapter’s activity on the Ethernet network.
For further information on Local Statistics, refer to the Network
Software Installation Guide.
1.3 RELATED MANUALS
• TPT-T 10BASE-T Transceiver User’s Manual
• Remote LANVIEW/Windows Station Software
User’s Manual
• SPECTRUM documentation
• Network Software Installation Guide
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Cabletron Systems Adaptateur
Cabletron Systems
Cabletron Systems TPFOT-2 Manuel utilisateur
Cabletron Systems
Cabletron Systems SmartSwitch 6C110 Manuel utilisateur
Cabletron Systems
Cabletron Systems E2210 Manuel utilisateur
Cabletron Systems
Cabletron Systems CTP100T Manuel utilisateur
Cabletron Systems
Cabletron Systems F3019 Manuel utilisateur
Cabletron Systems
Cabletron Systems E2210 Manuel d'exploitation et d'entretien
Cabletron Systems
Cabletron Systems EMC32-12 Manuel utilisateur
Cabletron Systems
Cabletron Systems COFOT-F1 Manuel utilisateur
Cabletron Systems
Cabletron Systems F6019 Manuel utilisateur
