BYOC Scrambled Octave Manuel utilisateur

Build Your Own Clone

Scrambled Octave

Kit Instructions

Warranty:

BYOC, LLC guarantees that your kit will be complete and that all parts and

components will arrive as described, functioning and free of defect. Soldering,

clipping, cutting, stripping, or using any of the components in any way voids this

guarantee. BYOC, LLC guarantees that the instructions for your kit will be free of

any majors errors that would cause you to permanently damage any components

in your kit, but does not guarantee that the instructions will be free of typos or

minor errors. BYOC, LLC does not warranty the completed pedal as a whole

functioning unit nor do we warranty any of the individual parts once they have

been used. If you have a component that is used, but feel it was defective prior to

you using it, we reserve the right to determine whether or not the component was

faulty upon arrival. Please direct all warranty issues to:

[email protected] This would include any missing parts issues.

Return:

BYOC, LLC accepts returns and exchanges on all products for any reason, as long as

they are unused. We do not accept partial kit returns. Returns and exchanges are for the

full purchase price less the cost of shipping and/or any promotional pricing. Return

shipping is the customer’s responsibility. This responsibility not only includes the cost of

shipping, but accountability of deliver as well. Please contact

[email protected] to receive a return authorization before mailing.

Tech Support:

BYOC, LLC makes no promises or guarantees that you will successfully complete your

kit in a satisfactory manner. Nor does BYOC, LLC promise or guarantee that you will

receive any technical support. Purchasing a product from BYOC, LLC does not entitle

you to any amount of technical support. BYOC, LLC does not promise or guarantee that

any technical support you may receive will be able to resolve any or all issues you may

be experiencing.

That being said, we will do our best to help you as much as we can. Our philosophy at

BYOC is that we will help you only as much as you are willing to help yourself. We

have a wonderful and friendly DIY discussion forum with an entire section devoted to the

technical support and modifications of BYOC kits.

www.buildyourownclone.com/board

When posting a tech support thread on the BYOC forum, please post it in the correct

lounge, and please title your thread appropriately. If everyone titles their threads

“HELP!”, then it makes it impossible for the people who are helping you to keep track of

your progress. A very brief description of your specific problem will do. It will also

make it easier to see if someone else is having or has had the same problem as you. The

question you are about to ask may already be answered. Here are a list of things that you

should include in the body of your tech support thread:

1. A detailed explanation of what the problem is. (not just, “It doesn’t work, help”)

2. Pic of the top side of your PCB.

3. Pic of the underside of your PCB.

4. Pic that clearly shows your footswitch/jack wiring and the wires going to the PCB

5. A pic that clearly shows your wiring going from the PCB to the pots and any other

switches(only if your kit has non-PC mounted pots and switches)

6. Is bypass working?

7. Does the LED come on?

8. If you answer yes to 6 and 7, what does the pedal do when it is "on"?

9. Battery or adapter.(if battery, is it good? If adapter, what type?)

Also, please only post pics that are in focus. You're only wasting both parties' time if you

post out of focus, low-res pics from your cell phone.

Revision Notes:

Rev 1.0 There are no known errors.

Rev 1.1 Changed Q2 to 2N3904

Copyrights:

All material in this document is copyrighted 2018 by BYOC, LLC

SCRAMBLED OCTAVE KIT

INSTRUCTION INDEX

Parts Checklist……………………..............…….....page 4 - 5

Populating the Circuit Board…………...................page 6 - 13

Main PCB Assembly…….........................................page 14 - 17

Wiring........................................................................page 18 - 21

Operation Overview.................................................page 22

Schematic...................................................................page 23

Parts Checklist for BYOC Scrambled Octave Kit

Resistors:

1 - 220ohm (red/red/black/black/brown)

1 - 1k (brown/black/black/brown/brown)

1 - 2k2 (red/red/black/brown/brown)

3 - 4k7 (yellow/purple/black/brown/brown)

1 - 8k2 (gray/red/black/brown/brown)

1 - 10k (brown/black/black/red/brown)

2 - 47k (yellow/purple/black/red/brown)

2 - 220k (red/red/black/orange/brown)

1 - 470k (yellow/purple/black/orange/brown)

3 - 1M (brown/black/black/yellow/brown)

Capacitors:

1 - 10n or .01µfilm (may say ‘103’ on the body)

2 - 1µaluminum electrolytic

3 - 4.7µf aluminum electrolytic

2 - 100µf aluminum electrolytic

Diodes:

5 - 1N456 (small black plastic with a silver or white stripe)

Transistors:

1 - 2N3904

3 - 2N5306

Potentiometers: Be sure to snap off the small tab on the side of each panel mounted

pot.

1 - B10k linear (TEXTURE)

1 - B50k audio (BLEND)

Hardware:

1 - drilled enclosure w/ 4 screws

1 - byoc classic Scrambled Octave PCB

1 - 3PDT footswitch

2 - knobs

2 - Lock Washers

1 - AC adaptor jack

1 - ¼”mono jack

1 - ¼”stereo jack

1 - red LED

1 - battery snap

4 - bumpers

hook-up wire

for a larger pic, go to www.buildyourownclone.com/scramblerguts.pdf

Populating the Circuit Board

STEP 1: Add the diodes. Be sure to match the end of the diode with the stripe to the

layout on the PCB. The stripped end should go in the square solder pad.

STEP 2: Add the resistors. Resistors are not polarized, so it does not matter which end

goes in which solder pad. Take your time and be sure not to confuse similarly banded

resistors such as the 470k with the 4k7 or the 220k with the 220 ohm. If you have

difficulty reading the color bands, use a digital multimeter to test the value of each

resistor.

Step 3: Add the film capacitor. These are not polarized and can be inserted into the PCB

either way.

Step 4: Add the Transistors. Be sure to orient the transistosr so that the flat side of the

tansistor body matches up with the flat side on the PCB layout. Make sure to insert the

2N3904 transistor into the Q2 space highlighted in yellow.

Table des matières

Autres manuels BYOC Pédale musicale

BYOC

BYOC Green Pony Manuel

BYOC

BYOC BA6110 Manuel utilisateur

BYOC

BYOC Classic Fuzz Manuel utilisateur

BYOC

BYOC Parametric EQ Manuel utilisateur

BYOC

BYOC Ultimate Fuzz Kit Manuel utilisateur

BYOC

BYOC El Distorto Segundo Manuel utilisateur

BYOC

BYOC Tremelo Manuel utilisateur

BYOC

BYOC Soaring Skillet Manuel utilisateur

BYOC

BYOC Shredder Manuel utilisateur

BYOC

BYOC Reverb Manuel utilisateur

BYOC

BYOC Classic Overdrive Kit Manuel utilisateur

BYOC

BYOC E.S.V. Fuzz Germanium Manuel utilisateur

BYOC

BYOC Lazy Sprocket Manuel utilisateur

BYOC

BYOC Classic Delay Manuel utilisateur

BYOC

BYOC Parametric Multi-Band Compressor Manuel utilisateur

BYOC

BYOC Octavefuzz Manuel utilisateur

BYOC

BYOC 27V Boost Manuel utilisateur

BYOC

BYOC Overdrive 2 Manuel

BYOC

BYOC Silver Pony 2 Manuel

BYOC

BYOC Octave Fuzz Manuel

BYOC

BYOC Gray 1976 Manuel utilisateur

BYOC

BYOC ESV Fuzz Silicon Manuel utilisateur

BYOC

BYOC Phase Royal Manuel utilisateur

BYOC

BYOC Divided Octave Manuel utilisateur

Manuels Pédale musicale populaires d'autres marques

Behringer

Behringer ULTRA WAH UW300 Manuel utilisateur

Whirlwind

Whirlwind oc-bass Manuel utilisateur

Strymon

Strymon Lex-rotary Manuel utilisateur

Behringer

Behringer PB600 Manuel utilisateur

Lexicon

Lexicon MX200 Manuel utilisateur

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manuel utilisateur

Matthews Effects

Matthews Effects Whaler V2 Manuel utilisateur

Grid 1

Grid 1 Pedal Jeanie Manuel utilisateur

Amptweaker

Amptweaker tightboost Manuel utilisateur

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manuel utilisateur

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manuel utilisateur

Dimavery

Dimavery EPVP-50 Manuel utilisateur

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manuel utilisateur

Pro-MIDI

Pro-MIDI G25 Manuel utilisateur

DW 7000 Manuel utilisateur

FAMC

FAMC Liquid-Foot Jr. Series Manuel utilisateur

Dimavery

Dimavery EPOD-50 Overdrive Manuel utilisateur

TREX

TREX ToneBug Totenschläger Manuel utilisateur