Bushranger MT2601 Manuel utilisateur

MULTI-TOOL

MT2601

OPERATOR’S MANUAL

Thank you for purchasing your Bushranger® Multi-Tool Trimmer.

This instruction manual will aid in the assembly, safe operation and maintenance of your Multi-Tool. Please read the following

warnings to ensure safety and the long life of your product.

Refer to page 7 - choke position.

Safety Markings and Symbols

IMPORTANT NOTES

Warning!

Read the directions for use

before operating the machine.

Wear safety goggles, a helmet

and ear protection.

Wear sturdy, non-slip footwear.

Wear safety gloves.

Protect the machine

from rain and damp conditions.

Be careful of objects

being thrown out!

Always switch off the machine

and pull off the spark plug

boot.

Read the direction before

carrying out any maintenance

work.

Do not use rigid cutting disk.

Do not use solid saw edged

All bystanders must be kept at

least 15 m from the machine.

Tool continues to run some

seconds after switching off

CAUTION: Hot machine parts.

Keep your distance.

• Read the instructions carefully. Ensure you are familiar with all controls & safety precautions outlined in this document

before operating the machine.

• Stay alert and watch what you are doing when operating the machine. Do not operate the multi-tool under the inﬂuence

of alcohol, drugs or medication or when you are tired or sick.

• Operate the multi-tool at reasonable hours only - not early in the morning or late at night or when people might be

disturbed. Check with your local council for operation times.

• Do not operate the multi-tool indoors or in conﬁned spaces.

• While the multi-tool is running, always keep hands and feet away from thetool head.

(Keep away from any bystanders or animals when in use.)

• Use only manufacturer’s genuine recommended replacement parts and accessories.

03 - 05

Do not use rigid cutting disk.

All bystanders must be kept at

least 15 m from the machine.

Tool continues to run some

seconds after switching off

CAUTION: Hot machine parts.

Keep your distance.

TABLE OF CONTENTS

Safety & Handling

Safety Instructions

Hazards

Personal Safety Equipment

Features & Deﬁnitions

Feature Deﬁnitions

Assembly Procedures

Handle

Guards

Split Shaft Assembly

Connection Of Attachment

Trimmer Line Fitting

Fitting Trimmer Head

Operating Instructions

Oil Fill Procedures

Fuelling procedures

Starting Instructions

Stopping Instructions

Maintenance & Care

Oil

Air Filter

Spark Plug

Storage

Maintenance Chart

Troubleshooting

10 - 11

15 - 17

22 - 23

Safety Instructions

SAFETY & HANDLING

Do not operate the Multi-Toolbefore reading all Instructions & reading all

Safety & Handling sections.

Operator Safety

• Wear the necessary safety equipment, as listed on page (6), in the Personal Safety Equipment Section.

• Always wear heavy, long pants. Do not wear loose clothing, jewellery, short pants, sandals or go barefoot. Secure hair

so it is above shoulder length.

• Do not operate the unit if you are tired, ill or under the inﬂuence of alcohol, drugs or medication.

Unit Safety

• The product is intended for garden maintenance trimming of organic ground covering such as grass and lawn. The

product must not be used for or modiﬁed for uses other than is intended, unless approved by the manufacturer.

• Inspect the entire unit and cutting head before each use.

• Ensure that the guard is properly attached.

• Do not use the unit if it is running erratically. Have it serviced promptly.

• Keep handles free of oil and fuel.

• Learn how to stop the engine quickly in an emergency.

• Stop the engine when the unit is unattended. Never leave engine running while unattended.

• Never allow children or unauthorised persons to operate the unit.

• Do not leave the unit on dry cuttings when it is Hot, as a risk of ﬁre is present. Do not cover mufﬂer or restrict airﬂow to

mufﬂer.

Fuel Safety

• Use a container approved for fuel and a funnel to avoid spillage.

• Pour fuel outdoors where there are no sparks or ﬂames.

• Frequently check for fuel leaks.

• Do not smoke or allow smoking near fuel, or near the unit, or while using the unit.

• Add fuel before starting the unit.

• Never remove the fuel tank cap while the engine is running or hot, allow to cool before refuelling.

• Never allow the unit to run out of fuel before refuelling.

Do not operate the Multi-Toolbefore reading all Instructions & reading all

Safety & Handling sections.

SAFETY & HANDLING

Fuel Safety Continued

• Move at least 3 metres away from the fuelling site before starting the engine.

• Wipe all traces of fuel on the unit before starting the engine.

• Change your clothes before starting the unit if fuel has been spilt on them.

Starting Safety

• Start the engine with feet well away from the cutting head.

• Ensure that the area of starting and operation is clear of sticks, stones, glass, nails, wire, string and debris, which could

be thrown by the cutting head.

Cutting Safety

• Use only in good visibility and favourable weather conditions.

• Keep children, animals and bystanders outside the 15 metre hazard zone. Stop the engine immediately if approached.

• Keep the engine to the right of your body, holding the unit with both hands.

• Keep a ﬁrm footing and balance. Do not over reach.

• Keep the cutting head below waist level and do not raise the engine above your shoulder. The cutting head can come

dangerously close to your body.

• Keep your body away from the cutting head and mufﬂer when the unit is running.

• Do not strike objects that may cause harm or damage to the unit.

Maintenance Safety

• Stop the engine and disconnect the spark plug before clearing blockages, checking or working on the unit. Clean

carbon from the mufﬂer at exhaust outlet frequently.

• Stop the engine, disconnect the spark plug and inspect the unit if it begins to vibrate abnormally or if it strikes a foreign

object.

• Use only genuine trimmer line. Never use wire, rope, string, etc.

• Use only genuine replacement parts.

SAFETY & HANDLING

Transporting and Storage

• Hand carry the unit with the engine stopped and the mufﬂer away from your body.

• Allow the engine to cool, empty the fuel tank and secure the unit before storing or transporting in a vehicle.

• Empty the fuel tank after each use and before storing the unit.

• Store the unit and fuel well away from sparks or open ﬂames from water heaters, electric motors, switches or furnaces,

etc.

• Store the unit out of reach of children and unauthorised persons.

Hazards

The following safety precautions must be strictly observed to avoid the risk of damage or personal injury.

Prior to using the unit, clear the operating area of objects which may be thrown up by

the cutting head, such as rocks, glass and other debris.

Do not start or operate the unit inside a closed room or building.

Breathing exhaust fumes can kill.

Be careful when operating the unit on slippery ground or overgrown terrain. Be

attentive for concealed hazards, such as ditches, tree stumps and roots.

Maintain solid footing and balance while operating the unit. Cut only on ground level.

Never use the unit without the guard securely in place.

Do not touch the cutting head in motion. When handling blade for assembly or

maintenance tasks, always wear protective gloves.

Bystanders must be at least 15 metres away during operation of the unit, as rocks and

other materials may be thrown at high velocities. Switch the unit off immediately if

approached.

Keep body away from hot mufﬂer parts.

Personal Safety Equipment

Always use the following safety equipment when working with your Multi-Tool:

• A safety helmet ﬁtted with a visor or suitable eye protection.

• A set of ear muffs.

• A pair of protective gloves.

• A pair of safety boots.

FEATURES & DEFINITIONS

Bent Shaft Trimmer

1. Bumphead Assembly

2. Oil Fill Bottle

3. Shaft Guard (inc 2 screws)

4. Loop Handle

5. Engine Stop Switch

6. Throttle Lever “Release”

7. Throttle Lever

8. Throttle Lever “Lock”

9. Choke Lever

10. Starter Cord

11. Fuel Cap

12. Air Filter Housing Cover

13. Fuel Tank

14. Engine Shroud - Cowling

15. Fuel Pump “Primer”

16. Shoulder Strap

17. Spark plug Wrench

18. Allen Key (4mm)

19. Allen Key (5mm)

20. Trimmer Attachments

21. Polesaw Attachment (Optional)

22. Hedge Trimmer Attachment (Optional)

85002 Pole Saw

Optional Accessory

85003 Hedge Trimmer

Optional Accessory

713 11

17 18

ASSEMBLY PROCEDURES

Handle Assembly

Fitting The Handle

1. Components - 4x Screws, Loop Handle & Clamp.

2. Place Handle (1) over the shaft in the desired location.

3. Insert Clamp (2) from the bottom side of the handle.

4. Insert screws (3) and washers (4) through loop handle and into threads of the clamp.

5. Tighten screws to lock handle into position.

CAUTION! Not too loose or too tight. Over tightening may damage the unit.

Fig. 1

Guard Assembly

Fitting The Straight Shaft Guard

1. Position the guard (3) by lining up the mounting holes on guard mount (2).

2. Secure the guard with two screws (1).

Fig. 2

ASSEMBLY PROCEDURES

Adjusting The Oil Flow Adjusting Chain Tension

Attaching Pole Saw Attachment

Attaching Hedge Trimmer Attachment / Adjusting Angle

Adjust Angle Of Gear Box

Fig. 3 Fig. 4 Fig. 5 Fig. 6

Fig. 7 Fig. 8 Fig. 9

Fig. 10 Fig. 11 Fig. 12 Fig. 13

Fig. 14 Fig. 15

Loosen Knob (1) Pull locating pin (2) Once attachment is located in

the drive release locating pin

(2) and tighten knob (1).

Loosen Lever (1). Move the blades to the

desired angle and re-tighten

lever (1).

Loosen knob (1). Pull locating pin (2). Once attachment is located in

the drive release locating pin

(2) and tighten knob (1).

Loosen screw (1). To adjust oil ﬂow, adjust

screws (2) anti-clockwise to

increase oil ﬂow clockwise

to decrease oil ﬂow. Once

adjusted tighten screw (1).

Loosen nut (1). Screw adjustment (2)

clockwise to tension chain to

required tension and retighten

nut 1.

Fig. 16 Fig. 17

ASSEMBLY PROCEDURES

Trimmer Line Assembly - Bump Head

Fitting The Handle

1. Press two cover clips inwards on the housing & remove the cover slowly.

Note: Retain the spring within the housing.

2. Remove the remains of worn line from the spool (if any remains).

Note: Remaining line may be sufﬁcient to rewind and reuse if has been tangled or has retracted back into the housing.

Note: Ensure inside of housing and spool are clean and free of grass & soil before reﬁlling.

3. Use 4 meters of diameter 2.4mm nylon line*. Fold the full length of line in the center and insert the centre fold into one

of the slots in the spool middle plate.

4. Wind the upper half of the line tightly CLOCKWISE onto the upper spool.

Note: ‘ CLOCKWISE ‘ direction when looking at the top of the spool as shown by the arrow in Fig. 21.

Continue winding until approximately 10cm remains at the end of the line and hold line end by locking into one of the four

notches on the top of the spool.

Repeat process with other half of the line winding in the SAME DIRECTION on thelower spool and hold the line end in an

opposite notch.

5. Put the spool back into the cover. Remove one end of the line from the spool notch & push it into an Eyelet slot. Repeat

for the other end of the line into the opposing Eyelet slot. Pull both ends of line tightly through the eyelets to remove any

excess slack in spool winding.

6. Push the spool and cover back into the housing so that the housing clips align with the cover and clicks back into place.

Upper Spool

Middle

Plate

Top of Spool

Notches in top

of spool

ASSEMBLYPROCEDURES

Trimmer Line Assembly - Bump Head

1. Press two cover clips inwards on the housing & remove the cover slowly.

Note: Retain the spring within the housing.

2. Remove the remains of worn line from the spool (if any remains).

Note: Remaining line may be sufficient to rewind and reuse if has been tangled

or has retracted back into the housing.

Note: Ensure inside of housing and spool are clean and free of grass & soil

before refilling.

3. Use 6 meters of diameter 2.4mm nylon line*. Fold the full length of line in the center

and insert the centre fold into one of the slots in the spool middle plate.

4. Wind the upper half of the line tightly CLOCKWISE onto the upper spool.

Note: ' CLOCKWISE ' direction when looking at the top of the spool as shown

by the arrow in Fig.4.

Continue winding until approximately 10cm remains at the end of the line and hold

line end by locking into one of the four notches on the top of the spool.

Repeat process with other half of the line winding in the SAME DIRECTION on the

lower spool and hold the line end in an opposite notch.

5. Put the spool back into the cover. Remove one end of the line from the spool notch

& push it into an Eyelet slot. Repeat for the other end of the line into the opposing

Eyelet slot. Pull both ends of line tightly through the eyelets to remove any excess

slack in spool winding.

6. Push the spool and cover back into the housing so that the housing clips align with

the cover and clicks back into place.

* 2.4mmø nylon line is recommended to provides best performance. The bump head can

be fitted with line diameters from 2mm to 3mm. The maximum length of the line that

can fit the head varies according to the line diameter. The maximum length capacity

using 2.4mmø is 6 metres. Do not overfill the head spool with excessive lengths of

line as it will result in ineffective spool feeding of line.

cover

spool

housing upper spool

middle

plate

Top of Spool

Notches in top

of spool

Housing

Spool

Cover

Fig. 18 Fig. 19 Fig. 20

Fig. 21 Fig. 22 Fig. 23

Table des matières

Autres manuels Bushranger Tondeuse

Bushranger

Bushranger HT2601 Manuel utilisateur

Bushranger

Bushranger B2600 Manuel utilisateur

Bushranger

Bushranger HT2600 Manuel utilisateur

Bushranger

Bushranger HT231 Manuel du propriétaire

Bushranger

Bushranger B2301 Manuel utilisateur

Bushranger

Bushranger L2501 Manuel utilisateur

Bushranger

Bushranger AHT261 Manuel du propriétaire

Bushranger

Bushranger 85003 Manuel utilisateur

Bushranger

Bushranger L2601 Manuel utilisateur

Bushranger

Bushranger MC-PX-2 Manuel du propriétaire

Bushranger

Bushranger HTS261 Manuel du propriétaire

Bushranger

Bushranger BRU36v9101 Manuel utilisateur

Bushranger

Bushranger HT241 Manuel du propriétaire

Bushranger

Bushranger BRU36v9301 Manuel utilisateur

Bushranger

Bushranger MCH252 Manuel du propriétaire

Bushranger

Bushranger 36V Battery powered Hedge Trimmer Manuel utilisateur

Manuels Tondeuse populaires d'autres marques

MTD

MTD HT 51 E Manuel utilisateur

McCulloch

McCulloch T22 LS Manuel utilisateur

COCKRAFT

COCKRAFT PRO HL36-S Manuel utilisateur

Grizzly

Grizzly CT 1800 Li Manuel utilisateur

Peco

Peco Z Trimmer ZT-3000 Manuel utilisateur

Solo

Solo 116 Manuel utilisateur

Stiga

Stiga ST 1200 Manuel utilisateur

Echo

Echo GT-225 - 10-09 Manuel utilisateur

RedMax

RedMax BT17 Manuel utilisateur

GreenWorks

GreenWorks STA806 Manuel utilisateur

Parkside

Parkside PHSL 900 A3 Manuel utilisateur

Gardeo

Gardeo PRO GPTHT2560 Manuel utilisateur

Park

Park DT-810870 Manuel utilisateur

Worx

Worx WG209 Manuel utilisateur

Gardenline

Gardenline 43671/HTKS26 Manuel utilisateur

Makita

Makita 3710 Manuel utilisateur

Champion

Champion 100683 Manuel utilisateur

Stihl

Stihl FS 311 Manuel utilisateur