Bushnell Image View 111026 Manuel utilisateur
Model #: 111026
LIT. #: 980828/0710
Instruction
Manual Version 2.0
3
WARNING
Do NOT look directly at the sun through your binoculars.
Doing so may cause permanent eye damage.
NOTE: To reset the camera if you experience problems or if the display becomes
unresponsive, remove the batteries for at least one minute, then re-install them.
4
Congratulations on your purchase of the Bushnell ImageView®binocular!
The Bushnell ImageView binocular takes the technology of digital
photography and combines it with a high-quality compact binocular.
This allows you to observe sporting events, wildlife, scenic vistas or
anything you would normally use a binocular for, and then save the
image in a built-in attached digital camera. You can then download these
images to your computer and e-mail them to your friends and family,
print out the pictures, or save them in a photo album for future use.
Before using the product, please read the instructions contained in this
manual and take time to familiarize yourself with the different parts and
features of the product.
5
Camera and Binocular Parts Guide
Power/
MODE
Button
Camera
Lens
Binocular
Focus
SNAP
Button
USB
Port
Remote
Jack
SD Card Slot
Tripod
Socket
Battery
Compartment
6
CAMERA PARTS
Setup and Basic Operation
The camera is powered by two AAA alkaline, lithium, or NiMh batteries (not1.
included). Insert batteries into the compartment, with the springs in contact with
the negative (at) end of each battery. A power meter on the left center of the
display indicates battery condition.
Insert an SD card ("upside down" with metal contacts facing up) in the slot if greater2.
storage is desired. You may use SD cards (not MMC cards) up to 8 GB capacity.
Press and hold the MODE button until the camera turns on. The camera will turn3.
o automatically after about one minute if no buttons are pressed. Note: when the
camera is connected to a computer via the supplied USB cable, the camera will power
on automatically, and draw power from the computer with no battery drain.
Hold the ImageView steady and press SNAP to take a picture (or start/stop4.
shooting a video, when the camera is in video mode). The camera focus is preset
to take sharp photos from appoximately 35 feet to innity.
When using a tripod, you can help avoid the eects of camera shake by plugging5.
the supplied remote shutter release into the jack next to the SD card slot, and
using the button on the remote rather than SNAP to take photos.
7
Setting Date & Time/ Using the Operational Modes
The ImageView will imprint the date and time in the bottom right corner of your photos.
To set the current date and time, after turning on the camera, press and hold both the
MODE and SNAP buttons at the same time, until the display begins to ash. The display
now shows the last two digits of the year. Press the MODE button to move the cursor to
the second digit if necessary. Press the SNAP button to advance the digit to the current
year ("10" for 2010, etc). Then press MODE to go to the next number, which is the month.
Again, use SNAP to change this to the current month. Following the month display is:
date, hour (24hr format), and minute-continue to set these following the same process
using the MODE and then SNAP buttons. When you have completed all of the date/time
settings, the display will stop ashing and return to normal. Note that you will need to
reset the date/time after replacing batteries.
Your ImageView is already setup to produce high quality results right out of the box,
and it is not necessary to use the MODE settings and make any changes to get good
results by simply pressing the SNAP button to take photos. However, as you might want
to shoot a video clip, delete one or more previous photos, or explore other options,
we recommend you review the available mode options listed on the following pages.
Briey pressing the MODE button will step through these operational modes in the
listed order, and you will see the icon for each mode along with its current setting on
the display. Use the SNAP button to select the desired setting for any mode. If you make
no changes, and the SNAP or MODE button is not pressed within 5 seconds, the camera
will return to normal operation and display.
8
Mode Icon Settings Description
Video Video
Camera
OFF, High
(640x480
pixels per
frame, 29 fps),
Low (320x240
pixels)
Select "Hi" (recommended) or "Lo" video
resolution instead of "OFF" to put the camera in
video mode. Wait a few seconds for the camera to
automatically return to the normal display, then
begin shooting by pressing SNAP. The counter
will show the elapsed time while recording the
video clip. Press SNAP again to stop shooting. The
counter will advance by one, indicating the video
le has been saved. Return to the video mode
setting and select OFF to reset the camera to still
photo mode.
Quality Hq or Lq High, Low Select "Hi" (recommended) or "Lo" quality to
choose the amount of le compression, which
aects the size of the photo le. "Lo" allows more
photos to be stored in memory, but at reduced
quality.
Resolution Hi or Lo High (2.0MP*),
Low (1.3 MP)
*via software
interpolation
Select "Hi" or "Lo" resolution, based on your
preference for more detailed photos (Hi) or being
able to take a greater number of photos (Lo).
Using the Operational Modes (Bold indicates default settings)
9
Mode Icon Settings Description
Line
Frequency
60 or 50 60 Hz, 50 Hz Set to match the AC power frequency (cycles) of
your country. This ensures that stills and videos
shot under uorescent lighting appear normal.
Continuous CT OFF, 3, 5 Select 3 or 5 frames to shoot a rapid series of
photos instead of a single frame when SNAP is
pressed (in normal still photo mode). To cancel,
enter this mode again and select OFF.
Memory
Access
MEM Sto (USB Mass
Storage), PC
(USB Camera)
Select "Sto" to access the SD card les when the
camera is connected to a computer with the USB
cable. "PC" allows the camera to be used as a live
USB/PC camera (note that the 8x magnication
and lack of close focus capability limits usefulness
in most size rooms.)
Delete Last LSt+Trash
Can
None-press
SNAP to delete
the last photo
or video
Select this mode and press SNAP to delete only
the last photo or video you took. The counter will
go down one number.
Using the Operational Modes
10
Mode Icon Settings Description
Delete All ALL+Trash
Can
None-press
SNAP to delete
all photo and
video les
Select this mode and press SNAP to erase the
entire memory contents (the counter resets to
zero). Use this after downloading your les, to
clear the memory so you can take new photos. If
"Delete All" is selected accidently, simply wait a
few seconds and the camera will return to normal
operation.
Format FOr+Trash
Can
None-press
SNAP to
format card
or internal
memory
If you are using a new SD card, or one previously
used in other devices, we recommend you select
Format and press SNAP before you start taking
photos, to the card is setup with the correct data
le system for this camera. Note that formatting a
card erases its contents-please be sure you have
backed up any previous les rst.
Self-Timer Clock OFF or On Photo is taken after a 10 second delay when SNAP
is pressed (in normal still photo mode.) This can be
used to avoid accidently shaking the camera when
the SNAP button is pressed. If the remote shutter
cable is available, it should be used instead of the
self timer when the camera is tripod mounted.
The timer automatically cancels after use.
Using the Operational Modes
Table des matières
Autres manuels Bushnell Jumelles
Bushnell
Bushnell ImageView 11-1026 Manuel utilisateur
Bushnell
Bushnell 190125 Manuel utilisateur
Bushnell
Bushnell Equinox Z 260501 Manuel utilisateur
Bushnell
Bushnell PRIME BP1025B Manuel utilisateur
Bushnell
Bushnell Infinity 61-8545 Manuel utilisateur
Bushnell
Bushnell ELITE1500ARCTM 20-5101 Manuel utilisateur
Bushnell
Bushnell 161001CM Manuel utilisateur
Bushnell
Bushnell ENGAGE X-10x42 Manuel utilisateur
Bushnell
Bushnell Night Vision 26-2036 Manuel utilisateur
Bushnell
Bushnell IMAGE VIEW 111024 Manuel utilisateur
Bushnell
Bushnell 260650 Manuel utilisateur
Bushnell
Bushnell LYNX 260401 Manuel utilisateur
Bushnell
Bushnell ImageView 118328 Manuel utilisateur
Bushnell
Bushnell NIGHT WATCH 263230CL Manuel utilisateur
Bushnell
Bushnell Marine 13-7500 Manuel utilisateur
Bushnell
Bushnell 11 0834 Manuel utilisateur
Bushnell
Bushnell Eddie Bauer Manuel utilisateur
Bushnell
Bushnell MATCH PRO BMP1556G Manuel utilisateur
Bushnell
Bushnell 62-0726 Manuel utilisateur
Bushnell
Bushnell ImageView 11-8200 Manuel utilisateur
