Bunn JDF-2 Instructions d'installation

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

www.bunnomatic.com

JDF-2

S/N JDF0005473 & UP

Preliminary copy

INSTALLATION & OPERATING MANUAL

To obtain the Illustrated Parts Catalog, visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE,

and the quickest way to obtain the catalog. Contact Buun-O-Matic Corporation at 1-800-286-6070 to obtain a paper

copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service.

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:

1) All equipment other than as speciﬁed below: 2 years parts and 1 year labor.

2) Electronic circuit and/or control boards: parts and labor for 3 years.

3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.

4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis:

parts and labor for 3 years or 30,000 pounds of coffee, whichever comes ﬁrst.

These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by

it will be commercially free of defects in material and workmanship existing at the time of manufacture and

appearing within the applicable warranty period. This warranty does not apply to any equipment, component or

part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect,

alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is

conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone

at (217) 529-6601 or by writing to Post Ofﬁce Box 3227, Springﬁeld, Illinois 62708-3227; 2) if requested by

BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior

authorization from BUNN that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR

ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN

are not authorized to make modiﬁcations to this warranty or to make additional warranties that are binding on

BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and

should not be relied upon.

If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its

exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts

and/or labor (during the applicable parts and labor warranty periods speciﬁed above) to repair the defective

components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace

the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF

THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S

SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost proﬁts, lost sales,

loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute

equipment, facilities or services, or any other special, incidental or consequential damages.

BUNN, and JDF-2 are either trademarks or registered trademarks of Bunn-O-Matic Corporation.

CONTENTS

Introduction & Warranty .....................................................................................2

User Notices .......................................................................................................3

Initial Set-Up & Electrical Requirements .............................................................4

Plumbing Requirements .....................................................................................4

Operating Controls..............................................................................................7

Initial Fill .............................................................................................................5

Dispenser Use.....................................................................................................9

Cleaning............................................................................................................10

Adjustments & Optional Settings ......................................................................13

Function Lists ...................................................................................................18

Troubleshooting ................................................................................................21

Coolant Diagram ...............................................................................................28

Schematic Wiring Diagram ...............................................................................29

38310 010406

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual. They were written for your protec-

tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels.

27442.0000

00986.0002

33461.0001

12559.0003

00656.0000

38310 010406

PLUMBING REQUIREMENTS

This dispenser must be connected to a COLD WATER system with operating pressure between 20 and 100

psi (138 and 690 kPa). This water source must be capable of producing a minimum ﬂow rate of 3 ﬂuid ounces

(88.7 milliliters) per second. A shut off valve should be installed in the line before the dispenser. Install a regula-

tor in the line when pressure is greater than 100 psi (690 kPa) to reduce it to 50 psi (345 kPa). Also if the install

location experiences pressure ﬂuctuations greater than 20 psi (138kPa). The main water inlet is a 3/8” (9.52

mm) MFL connection.

Additionally, the dispenser’s rinse connection may be connected to a HOT WATER system.

Caution:

MAXIMUM RINSE WATER TEMPERATURE: 170 degrees F (76.6 degrees C)

Use BUNN-O-MATIC tubing, part number 34325.10_ _ (see Illustrated Parts Catalog for complete part num-

ber) for hot water connection.

The rinse water operating pressure must be between 20 and 100 psi (138 and 690 kPa). A shut off valve

should be installed in the line before the dispenser. Install a regulator in the line when pressure is greater than

100 psi (690 kPa) to reduce it to 50 psi (345 kPa). The rinse water inlet is a 1/4” (6.35 mm) MFL connection.

INITIAL SET-UP

CAUTION: The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or

move the dispenser. Place dispenser on a sturdy counter or shelf able to support at least 150 lbs. (68 kg). The

JDF-2 is designed for indoor use only.

Set the dispenser on the counter where it will be used. The JDF-2 requires a minimum of 4 inches (102 mm)

of air clearance at the rear and 8 inches (203 mm) of air clearance above the dispenser. Minimal clearance is

required between the dispenser sides and the wall or another appliance. For optimum performance, do not let

warm air from surrounding machines blow on the JDF-2. Leave some space so the dispenser can be moved for

cleaning.

ELECTRICAL REQUIREMENTS

CAUTION: The dispenser must be disconnected from the power source until speciﬁed in Electrical Hook-Up.

The 120V rated dispensers have an attached cord set and require a 2-wire, grounded, individual branch circuit

rated 120 volts ac, 15 amp, single phase, 60Hz. The mating connector must be a NEMA 5-15R. (Refer to the data

plate for exact electrical requirements.)

The 230V rated dispensers have an attached cord that requires an attachment plug cap rated at least 10a,

230V. The attachment plug cap must meet with applicable national/local electrical codes.

ELECTRICAL HOOK-UP

CAUTION: Improper electrical installation will damage electronic components.

1. An electrician must provide electrical service as speciﬁed.

2. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

3. Connect the dispenser to the power source.

4. If plumbing is to be hooked up later, be sure the dispenser is disconnected from the power source. If plumb-

ing has been hooked up, the dispenser is ready for Initial Fill.

38310 062205

NOTE- At least 18 inches (457 mm) of an FDA approved ﬂexible beverage tubing, such as reinforced braided

polyethylene, before the dispenser will facilitate movement to clean the countertop. It can be purchased direct

from BUNN-O-MATIC (part number 34325.10_ _ [see Illustrated Parts Catalog for complete part number.])

BUNN-O-MATIC does not recommend the use of saddle valves to install the dispenser. The size and shape of the

hole(s) made in the supply line(s) by saddle valves may restrict water ﬂow.

Note- A water strainer (Bunn-O-Matic part number 23720.1000) should be installed in line, prior to the ﬂex-

ible water line. This strainer is supplied loose with the dispenser. (See Fig. 2 for proper locations)

This equipment must be installed to comply with the Basic Plumbing Code of the Building Ofﬁcials

and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the

Food and Drug Administration (FDA). For models installed outside the U.S.A., you must comply with

the applicable Plumbing/Sanitation Code for your area.

INITIAL FILL

CAUTION: The dispenser must be disconnected from the power source throughout the initial ﬁll except when

speciﬁed in the instructions.

1. Remove drip tray assembly and splash panel from the dispenser.

2. Pull the overﬂow tube from its retaining clip and connect it to the main water source (black gasket is supplied

in install kit).

3. Connect dispenser to the power source.

4. Slowly open the water shut off valve and ﬁll the water bath until water trickles from the overﬂow. The dispenser

will beep for three seconds when bath is approaching full. Reduce the ﬂow rate at this time.

5. After 3 minutes of power, slowly add more water to the tank until water trickles from overﬂow again.

6. Once water bath is ﬁlled, remove water source, cap dispenser ﬁll line, and store the ﬁll tube in it’s holder (the

ﬁll tube can now be used as a sight glass).

7. Replace the splash panel and drip tray.

8. Place refrigeration switch to the “ON” position. It will take approximately three hours at 75° F (24° C) ambient

to create the ice bank required for full dispenser performance. During this time, some further trickling from

the water bath is expected due to expansion caused by ice bank formation. While the refrigeration system is

creating the ice bank, the dispenser may be readied for use as described in Plumbing, Loading, Priming and

Adjustment.

PLUMBING REQUIREMENTS (cont)

FIG 1 Initial Fill Connection

P2655

38310 010406

Frozen Concentrates

1. Thaw the frozen concentrate in a refrigerated 35-40 degrees F (1.6-4.4 degrees C) environment for 36 to 48

hours before use.

2. Thoroughly mix the thawed concentrate by vigorously shaking the product container.

3. Open the dispenser door.

4. Prior to placing the product container in the dispenser, make sure that the o-ring on the container adapter is

lubricated. This will ease removal of the container when it becomes necessary.

5. Place the product container in the desired position and press it ﬁrmly into the bottle adapter opening.

6. Open the vent hole in the product container.

Note: Concentrate in the container must be completely thawed and be within the temperature range of 35-40

degrees F (1.6-4.4 degrees C.) Product outside of this temperature range, especially below, will produce an

“out of brix” drink.

Ambient Concentrates (Optional)

1. Install an Ambient Concentrate Conversion Kit (BUNN-O-MATIC part number 33699.0001) per the instruc-

tions provided in the kit.

2. Attach the concentrate product hose to the appropriate concentrate line located at the rear of the dispens-

er.

3. Attach the other end of the product hose to the product container through an appropriate ﬁtting.

PRIMING

1. Open the dispenser door

2. Load concentrate per instructions in section titled Loading.

3. Close the dispenser door. NOTE: The dispenser will not operate with the door open.

4. Place a large container under the appropriate dispense nozzle.

5. Dispensers with Press and Hold Feature:

Press and hold the “Product Dispense Switch” Fig 4, until concentrate dispenses from the dispense

nozzle.

Dispensers with Portion Control Feature:

Press and hold the “+/STOP Switch” Fig 5, until concentrate dispenses from the dispense nozzle.

Note: This may take several seconds, depending on the installation and programmed pump speed.

FIG 2 Plumbing Connections

PLUMBING HOOKUP

All plumbing connections are located on the rear of the dispenser. For Models prior to the Water Inlet Valve,

both the rinse and potable water line must be connected to a water source.

P2656

38310 012207

Models w/Water Inlet Valve Prior to Models w/Water Inlet Valve

P3805

OPERATING CONTROLS

FIG 3 Refrigeration Switch

FIG 4 Sanitize Switch P2657

P2261

38310 062205

Refrigeration Switch

The refrigeration switch is located on the top of the dispenser near the

left rear corner. This switch controls power to the compressor and the

condenser fan motor.

Sanitize Switch

The sanitize switch is located behind the drip tray in the lower left

corner of the chassis. The drip tray can be removed to provide easy

access to the switch. The sanitize switch is used to enter and exit the

sanitize mode and to initiate the sanitize automatic cycle. Refer to

Weekly Sanitizing in the Cleaning section for detailed instructions on

the use of this switch.

OPERATING CONTROLS (cont.)

FIG 5 Press and Hold Models

A. Product Dispense Switch

Pressing and holding switch will initiate product ﬂow from the respective nozzle; releasing the switch will

stop the ﬂow.

B. Hidden Switch

These switches are used to access, change and exit the dispenser program mode.

C. Lock Switch

This switch is used to lockout the dispensing capabilities.

FIG 6 Portion Control Models

B. Hidden Switch

These switches are used to access, change and exit the dispenser program mode.

C. Lock Switch

This switch is used to lockout the dispensing capabilities.

D. Product Dispense Switch

Momentarily pressing and releasing one of the switches will initiate a timed dispense. Each station has three

different timed dispenses which are preset at the factory. Refer to DISPENSER USE section for preset volumes

and adjustment procedures.

E. Plus/Stop Switch

This switch can be used to “top-off” a beverage. Pressing and holding switch will initiate product ﬂow from

the respective nozzle; releasing the switch will stop the ﬂow. Momentarily pressing this switch during a timed

dispense will stop the ﬂow.

EEC

38310 062205

DISPENSER USE

Press and Hold Models (Refer to Fig 5)

1. Place a cup on the drip tray beneath the desired dispensing nozzle.

2. Press and hold the “Product Dispense” switch until the beverage reaches the desired level, then release.

Portion Control Models (Refer to Fig 6)

1. Place a cup on the drip tray beneath the desired dispensing nozzle.

2. Momentarily press the appropriate cup size switch to dispense the beverage. The dispenser is factory preset

to produce the approximate beverage sizes as follows:

Small (4.0 seconds): approximately 7 ﬂ.oz. (207 ml)

Medium (6.9 seconds): approximately 12 ﬂ.oz. (355 ml)

Large (9.1 seconds): approximately 16 ﬂ.oz. (473 ml)

The dispense times can be individually programmed by following the procedures described in ADJUST-

MENT - Cup Size Programming.

To stop a timed dispense, momentarily press the “+/Stop Switch”.

3. To “top-off” a beverage, press and hold the “+/Stop Switch” until the beverage reaches the desired level, then

release.

38310 062205

CLEANING & PREVENTIVE MAINTENANCE

General Cleaning and Sanitizing Procedures

Note: The Bunn Juice Dispenser incorporates a rinse reminder feature which

lights the rinse led on the front panel when it is time to rinse. See dip switch

function list to activate this feature.

Daily: Rinse Procedure

Tools required: 32 oz. (946 ml) minimum empty container

1. Open the refrigerated compartment’s door to access the “DISPENSE/RINSE”

Knobs Fig 7.

2. Select the stations that will be rinsed and then rotate the appropriate Knob(s)

to the rinse position. It is recommended that ALL dispense heads be rinsed

daily. Note: If a station is in service lockout, leave its knob in the Dispense

position.

3. Close the refrigerated compartment’s door.

4. Place the empty container under the dispense nozzle to catch the rinse water.

(CAUTION: THE BUNN JUICE DISPENSER CAN BE PLUMBED FOR A HOT WATER RINSE. RINSE WATER CAUGHT

IN THIS STEP SHOULD BE HANDLED WITH EXTREME CARE.)

5. Press and release the appropriate “Product Dispense Switch” Fig 5. This will initiate a timed rinse cycle. Por-

tion control users can press any of the 3 “Product Dispense Switches” Fig 6, to initiate a timed rinse cycle.

6. Repeat for each dispense head.

7. Open the refrigerated compartment’s door and return each knob to the dispense position.

8. Actuate the station’s Dispense Switch until concentrate appears from the dispense nozzle.

Daily: Parts Washing

1. Remove and wash the dispense nozzle(s), mixing element(s), drip tray and drip tray cover in a mild detergent

solution. Rinse thoroughly.

2. Wipe splash panel, areas around dispense nozzle(s), and drip trough in refrigerated compartment with a

clean, damp cloth.

Weekly: Sanitizing

Tools required: Nozzle tubing (BUNN-O-MATIC part number 03289.1002) recommended when sanitizing multiple

dispense heads simultaneously, 1 empty 5 gallon (18.9 L) bucket, 2 packets of Kay 5 sanitizer, and clean, empty

concentrate containers.

Note: The Bunn juice dispenser features a semiautomatic sanitizing program. When sanitizing multiple heads

simultaneously, attach Bunn sanitize tubing (BUNN-O-MATIC part number 03289.1002) on the end of each

dispense nozzle and run tubing to the 5 gallon (18.9 L) bucket.

1. Remove any juice concentrate from the dispenser and store in a separate refrigerated compartment.

2. Perform the rinse procedures as previously described. (Note: If the dispenser is plumbed for hot water rinse,

proceed to step 9.)

3. Fill clean empty concentrate container(s) with approximately 128 oz. (3.8L) of the hot tap water (approxi-

mately 140°F (60°C). Load the containers of hot water into the dispenser (just like concentrate). Verify the

rinse knobs are in the “DISPENSE” position.

4. Remove the drip tray and verify that the nozzle tubes are positioned within the empty bucket.

5. Press and hold the “Sanitize Switch” Fig 5, located on the front left portion of the base, for 5 seconds. The

“SANITIZE” indicator on the front panel will begin to ﬂash and the beeper will sound twice indicating that

you have entered the sanitize mode.

FIG 7 Dispense/Rinse Switch

38310 062205

Autres manuels pour JDF-2

Table des matières

Autres manuels Bunn presse-agrumes

Bunn

Bunn JDF-2 Guide de référence rapide

Manuels presse-agrumes populaires d'autres marques

GE 169201 Manuel utilisateur

Exquisit

Exquisit ZP 3001 WET Manuel utilisateur

Philips

Philips HR1851 Manuel utilisateur

Sam Cook

Sam Cook MASTERCHEF EXECUTIVE PSC-50 Manuel utilisateur

Termozeta

Termozeta spremiagrumi Manuel utilisateur

ElectrIQ

ElectrIQ WF1000 Manuel utilisateur

Bella

Bella WHOLE FRUIT JUICER Manuel utilisateur

HAEGER

HAEGER Little Juice CJ-025 006A Manuel utilisateur

Havells

Havells Fusion Manuel utilisateur

Siemens

Siemens MK554 SERIES Manuel utilisateur

Beper

Beper 90.302B Guide rapide

NATURSAFT

NATURSAFT 015.401.3 Manuel utilisateur

Moulinex

Moulinex BKB 2 Manuel utilisateur

Royal Catering

Royal Catering RCJU-01 Manuel utilisateur

camry

camry CR 4002 Manuel utilisateur

AIGOSTAR

AIGOSTAR 30HIM Manuel utilisateur

ZUMEX

ZUMEX MINEX Manuel utilisateur

Skymsen

Skymsen EX Manuel utilisateur