Bunker Hill Security 62447 Instructions de montage

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

REV 14h

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 62447

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future reference.

1. Position batteries in proper polarity

and do not install batteries of

different types, charge levels,

or capacities together.

2. Keep installation area clean.

Cluttered areas invite accidents.

3. Observe installation area

conditions. Keep work area

well lit during installation.

4. Check for damaged parts. Before

using any product, any part that appears

damaged should be carefully checked

to determine that it will operate properly

and perform its intended function.

Check for any broken or damaged

parts and any other conditions that may

affect its operation. Replace or repair

damaged or worn parts immediately. Do

not use the Alert System if any switch

does not turn on and off properly.

5. Replacement parts and accessories.

When servicing, use only identical

replacement parts. Use of any

other parts will void the warranty.

6. Keep children away. Mount the Sensor

and Receiver out of children’s reach.

7. Dress properly. Protective,

electrically non-conductive

clothes and nonskid footwear are

recommended when working with

the Alert System. Wear restrictive

hair covering to contain long hair.

Page 3For technical questions, please call 1-888-866-5797.Item 62447

8. Use eye protection. Wear ANSI-

approved impact safety goggles

when setting up this product.

9. Maintain products with care. Keep the

Alert System clean for better and safer

performance. Inspect the components

periodically. If damaged, have it

repaired by a qualified technician.

10. Do not overreach. Keep proper footing

and balance at all times. If a ladder

is to be used during installation, it

should be supported by an assistant.

11. Do not set up the Alert System

if under the influence of alcohol

or drugs. Read warning labels on

prescriptions to determine if your

judgement or reflexes are impaired

while taking drugs. If there is any

doubt, do not set up the Light.

12. Have your power tool serviced by

a qualified repair person using

only identical replacement parts.

This will ensure that the safety of

the power tool is maintained.

13. The warnings, precautions, and

instructions discussed in this instruction

manual cannot cover all possible

conditions and situations that may

occur. It must be understood by the

operator that common sense and

caution are factors which cannot

be built into this product, but must

be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Page 4 For technical questions, please call 1-888-866-5797. Item 62447

Functional Description

Specifications

Sensor Module

Passive Infrared (PIR) motion detector

Transmitter: 433 MHz, range up to 400'

Sensor Detection: 40° angle coverage at 30', mounted at 4' high

Battery: 1 9V (not included)

Low battery LED indicator

Receiver Module

Range: Up to 400' from Sensor Module

Battery: 3 C (not included)

Switch with three settings: Off/Hi/Low

Input connector for 6V DC Adapter (not included)

Low battery LED indicator

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC ID: YI6RL-9816B

Components and Controls

Figure A

Sensor

Receiver

Switch

(On Side)

DC Jack

(On Side)

Page 5For technical questions, please call 1-888-866-5797.Item 62447

Setup Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the

beginning of this document including all text under subheadings therein

before set up or use of this product.

Installing Batteries

CAUTION: Position batteries in

proper polarity and do not install

batteries of different types, charge

levels, or capacities together.

1. Using a screwdriver (not included),

remove the Battery Cover of the

Sensor, and insert one 9V battery (not

included). Replace the Battery Cover.

2. Using a screwdriver (not included),

remove the Battery Cover of the

Receiver, and insert three

C batteries (not included).

Replace the Battery Cover.

Note: An optional 6 volt, 200 mA power

adapter (not included) can be used to

power the Receiver instead of batteries.

Installing the Sensor and Receiver

CAUTION: Verify that installation

surface has no hidden utility lines

before drilling or driving screws.

1. Consider the following when

choosing a location for the Sensor:

a. The passive infrared sensor detects

heat. Avoid aiming it towards

areas that produce heat such as

heater vents, windows where the

sun hits, or outdoor spotlights.

b. Mount the Sensor at least three

feet above the ground. If placed

under the garage eaves, be sure

that the Sensor is not blocked

by the roof facia board.

c. If placed above eight feet high,

the Sensor should be aimed

downward so that it is pointed

toward the area being monitored.

2. Mount the Sensor to a flat

surface with hardware (3).

3. Place the Receiver within

400 feet of the Sensor.

Note: Obstructions may reduce

the receiving range.

4. Mount the Receiver to a flat surface

with hardware, or stand on a

flat surface. The receiver is not

intended to be weather resistant.

Note: Do not install the receiver in a

location that will get wet or directly

exposed to the elements.

Page 6 For technical questions, please call 1-888-866-5797. Item 62447

Operation

Power Switch

The Power Switch has three settings:

a. Off: Power is off.

b. Hi: A loud beep will sound

(approximately 92dB) and the LED

will flash when motion is detected.

c. Low: A short beep will sound

(approximately 80dB) and the LED

will flash when motion is detected.

Operation

1. To operate the Security Alert, slide

the Power Switch on the Receiver

to the “Hi” setting. Allow 30 seconds

for warm-up. Two short beeps will

sound, indicating the unit is working.

2. Test the Sensor by walking or

driving into the protected area.

Another person should be listening

for the alarm to sound.

3. If the Sensor does not activate,

Sensor relocation or aiming

adjustment will be required.

4. If the Receiver does not activate with the

sensor, reposition them closer together.

5. Once you have determined that the unit

is working properly, leave in the “Hi”

setting or adjust to the “Low” setting.

Low Battery

1. Replace the Sensor batteries when

the LED on the Sensor turns on.

2. Replace the Receiver batteries when

the LED on the Receiver turns on.

Page 7For technical questions, please call 1-888-866-5797.Item 62447

Parts List

Part Description Qty

1 Sensor 1

2 Receiver 1

Part Description Qty

3 Hardware 1

Record Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Maintenance

Procedures not specifically explained in this manual must be performed

only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:

Do not use damaged equipment. If abnormal noise or vibration

occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the

general condition of the tool. Check for:

• leaking, swollen, or cracked batteries,

• loose hardware,

• misalignment or binding of parts,

• cracked or broken parts, and

• any other condition that may

affect its safe operation.

2. AFTER USE, wipe external surfaces

of the tool with clean cloth.

3. Replace the batteries in the

Receiver or Sensor when their low

battery LED indicator lights.

4. There are no replaceable parts on

the Receiver or Sensor units.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality

and durability standards, and warrants to the original purchaser that this product is free from

defects in materials and workmanship for the period of 90 days from the date of purchase.

This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence

or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,

normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,

injuries to persons or property, or for incidental, contingent, special or consequential damages

arising from the use of our product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to you.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation

charges prepaid. Proof of purchase date and an explanation of the complaint must accompany

the merchandise. If our inspection verifies the defect, we will either repair or replace

the product at our election or we may elect to refund the purchase price if we cannot readily

and quickly provide you with a replacement. We will return repaired products at our expense,

but if we determine there is no defect, or that the defect resulted from causes not within

the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797

Table des matières

Autres manuels Bunker Hill Security Système de sécurité

Bunker Hill Security

Bunker Hill Security 68332 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security RL-9816B Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 60565 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 62368 Instructions de montage

Bunker Hill Security

Bunker Hill Security 94799 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 57937 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 93068 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 68332 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 62284 Instructions de montage

Bunker Hill Security

Bunker Hill Security 64734 Instructions de montage

Bunker Hill Security

Bunker Hill Security 66704 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur