Bulldog Security IMMOBILIZER Manuel utilisateur

CONTENTS

REMOTE STARTER IMMOBILIZER • SILENT GUARD

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

System Features ......................................1

System Components ....................................1

Required Tools .......................................1

Technical Assistance .................................1

Before You Begin .....................................1

Precautions ........................................1-2

Making Connections .................................2-3

Locating and Making Connections ....................3-4

Antenna Placement ....................................4

How to use Your Remote Transmitter ...................4

OEM Wiring Chart .....................................5

TECHNICAL ASSISTANCE

Should you need help. First check our website at www.bulldogsecurity.com/wires.htm or call our toll-free

Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM EST at 800-878-8007.

You must give the following information:

•Name

•Telephone Number with Area Code (Fax number if applicable)

•Year, Make, and Model of the vehicle

•The model number of the system you are installing

•The type of assistance you are requesting

If you give the above information you will be called back as soon as possible, usually within 10 minutes.

SYSTEM FEATURES

SYSTEM COMPONENTS

REQUIRED TOOLS

BEFORE YOU BEGIN

PRECAUTIONS

Congratulations, you have purchased the most advanced remote control immobilizer system ever made. Your

new system is a technological breakthrough utilizing the most advanced state of the art technology and

components. It is computer controlled and manufactured in the U.S.A. The dependability and variety of

features make Bulldog Security the leader in the industry. Enjoy your new system for years to come!

We recommend you read this installation manual thoroughly before starting the installation. This manual

will supply you with time-saving information. Each step will guide you to a correct installation.

You will need to decide where you will be placing the L.E.D. before you begin the installation.

Since there are many different makes and models of vehicles, it is impossible for this manual to cover

every wiring configuration. Instead, this manual will help you determine the correct connections and testing

procedures for your vehicle.

SAFETY FIRST!

A periodic safety check is recommended to ensure that your system is in proper working order.

DO NOT use mechanical wiring connections, such as crimp or snap together taps. Follow instructions on

pages 6-8.

DO NOT disconnect the battery if the vehicle has an anti-theft-coded radio or is equipped with an airbag.

Doing so may cause a warning light to be displayed and may require a trip to the dealer to be corrected.

Two-Button Extended Range Remotely immobilize your car’s engine Remote Control from an extended distance.

Valet Mode Remotely turn your immobilizer on and off.

Limited Lifetime Warranty Guarantees life-long protection.

Your system includes:

1-Installation & Operation Guide

1-Main Control Module and Harness 2-Two Button Remote Transmitters

1-High luminescence L.E.D. status indicator

You will need a computer-friendly test light, electrical tape, extra 16 awg wire and wire strippers or

cutters.

TESTING YOUR WIRES

MAKING WIRING CONNECTIONS

4. Insert the wire from the unit through the hole as shown.

6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the

connection. First pull the wire that you have just connected along side the wire you connected

to, tape and wire tie them together. Use this method for all connections.

CAUTION: All wires must be wrapped and taped.

5. Wrap the wire around one side then the other and finally around itself as shown.

Wire Tie

Electrical Tape

1. Strip back two inches of insulation on the wire from the keyless entry.

2. Strip back one inch of insulation on the wire you need to connect to.

One Inch of Bare Wire

Two Inches of Bare Wire

3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire

through.

MAKING END TO END CONNECTIONS

FOLLOW THESE INSTRUCTIONS

When testing for a positive or negative voltage, you must use a computer friendly test light (logic probe)

or a volt/ohm meter. Make sure to probe and test each wire before making your connections.

DO NOT leave the interior or exterior lights on for an extended period of time as it may cause battery

drain. Remove the dome light fuse from the vehicle’s fuse box.

DO NOT mount the control module until all connections have been made and tested. Using wire ties or double

sided tape MOUNT THE MODULE UNDER THE DRIVER’S DASH.

4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection.

Secure with wire ties as shown.

3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires

up to meet the left wire as shown.

2. Twist upper wires together, twist lower wires together as shown.

1. When tying two separate wires together at their ends, strip back 1” of insulation on both

wires and separate the strands of wire as shown below.

Use this method ONLY when connecting two separate wires end to end.

Wire Tie

Electrical Tape

Wire Tie

LOCATING & MAKING CONNECTIONS

GROUND

Connect the ground wire #7 to a clean unpainted metal surface under the dash.

12 VOLT CONSTANT

Connect the wire marked #8 (constant +12 volts) to constant 12 volts located at the ignition harness.

NOTE: Silent Guard will emit a series of chirps to indicate the unit is powered up.

IGNITION INPUT / IGNITION OUTPUT

Locate the primary factory ignition wire located at the ignition harness near the steering wheel column,

cut in two. Connect the wire marked #1 (ignition input) to the vehicle’s factory ignition wire leading

from the ignition key side. Connect the wire #4 (ignition output) to the other half of the factory

ignition wire.

Note: Remove any paint from

under bolt.

Factory Bolt Wire #7

ANTENNA PLACEMENT

ANTENNA

For best results, run the antenna (small gauge unmarked wire

from the front of the unit) as straight as possible. Do not

place the antenna next to any metal parts or the vehicle’s

main computer control module. MODULE

L.E.D.

FUEL INPUT

FUEL OUTPUT

IGNITION INPUT

IGNITION OUPUT

STARTER INPUT

STARTER OUTPUT

ANTENNA

GROUND

+12 VOLT CONSTANT

38752416

BUTTON #1

Disarm/Valet Off

BUTTON #2

Valet On

BULLDOG

Disarm

To be able to start the vehicle, press and release Button

#1. The LED will stop flashing and the Silent Guard will

emit one chirp. After disarming the unit, a 30 second window

will open to allow the user to start the vehicle. If the

vehicle is not started within 30 seconds the unit will

automatically immobilize your vehicle. After this 30 second

window has expired, and the LED will flash.

Arm

The Silent Guard is designed to automatically arm 30 seconds

after the ignition is turned off, unless the system is in

valet mode.

HOW TO USE YOUR REMOTE TRANSMITTER

Enter Valet Mode

Press and hold Button #2 for 5 seconds. The LED will light up constantly and the Silent Guard will emit two

chirps. While in valet mode, the Silent Guard will constantly chirp when the ignition is in the ON position.

Exit Valet Mode

Press and release Button #1. The LED will shut off and the Silent Guard will emit one chirp. The Silent Guard

will automatically arm in 30 seconds.

STARTER INPUT / STARTER OUTPUT

Locate the crank (starter solenoid) wire in the ignition harness, cut in two. Connect the wire marked

#2 (starter input) to the vehicle’s factory crank wire from the ignition key side. Connect the wire

marked #5 (starter output) to the other half of the factory crank wire leading out to the starter solenoid

(engine).

FUEL INPUT / FUEL OUTPUT

Locate the fuel pump power wire, in some vehicles you can find this wire located at the factory fuse

panel, it will be labeled fuel pump or injectors. If your vehicle doesn’t have this, please refer to

your vehicle’s wire schematic. Once you locate the wire, cut it in two. Connect wire #3(fuel pump input)

to the 12 volt supply going to the fuel pump ignition key side. Connect wire #6 (fuel pump output) to

the half of the factory fuel pump wire leading out to the fuel pump.

L.E.D.

Locate a good spot for the L.E.D., visible from all sides of the vehicle. If you wish to drill a hole,

use a 5/16 inch drill bit to mount the L.E.D. If you or your customer wishes not to have the L.E.D.

permanently mounted, use the included double-sided adhesive L-bracket to mount the L.E.D.

OEM WIRING CHART

MAKE CONST.12V+ STARTER IGN 1 IGN 2 IGN 3 ACCESS. LOCATION

GM RED YELLOW PINK WHITE GREEN ORANGE IGN. HARNESS

VIOLET PNK/WHT BROWN

BLUE/WHT

FORD CORP. YELLOW RED/BLUE RD/L.GRN BLK/GRN RED/BLK GRAY/YEL IGN. HARNESS

WHT/PINK BRN/PINK PNK/BLK

CHRYSLER CORP.RED YELLOW BLUE BLK/WHT N/A BLK/OR IGN. HARNESS

HONDA CORP. WHITE BLK/WHT BLK/YEL YELLOW N/A BLK/WHT IGN. HARNESS

MAZDA BLACK BLK/YEL BLK/WHT BLK/RED N/A BLUE IGN. HARNESS

BLK/BLUE

MITSUBISHI RED/BLACK BLK/YEL BLK/WHT BLUE/BLK N/A BLUE IGN. HARNESS

BLK/RED WHITE

NISSAN CORP. WHITE/RED BLK/YEL BLK/RED BLK/PNK N/A WHT/BLUE IGN. HARNESS

BLK/WHT RED/YEL

SUBARU BLK/YELLOW BLK/YEL BLACK BLUE N/A BLUE IGN. HARNESS

BLK/WHITE RED/YEL

TOYOTA CORP. WHITE BLK/WHT BLK/OR BLK/YEL N/A BLUE/RED IGN. HARNESS

WHITE/RED BLACK BLUE/RED PNK/BLUE

VW RED RED/BLK BLACK BLK/YEL N/A BRN/RED IGN. HARNESS

BLK/YEL BRN/RED

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bulldog Security Démarreur à distance

Bulldog Security

Bulldog Security 1200E Mode d’emploi

Bulldog Security

Bulldog Security RS82 Mode d’emploi

Bulldog Security

Bulldog Security selling remote starter Manuel utilisateur

Bulldog Security

Bulldog Security RS1100 Manuel utilisateur

Bulldog Security

Bulldog Security RS1300E Mode d’emploi

Bulldog Security

Bulldog Security Deluxe 62 Mode d’emploi

Bulldog Security

Bulldog Security RS1100 Mode d’emploi

Bulldog Security

Bulldog Security Remote Starter Manuel utilisateur

Bulldog Security

Bulldog Security RS102 Manuel utilisateur

Bulldog Security

Bulldog Security Deluxe 62I Mode d’emploi

Bulldog Security

Bulldog Security Deluxe 22I Mode d’emploi

Bulldog Security

Bulldog Security Deluxe 12I Mode d’emploi

Bulldog Security

Bulldog Security RS202 Mode d’emploi

Bulldog Security

Bulldog Security RS302 Mode d’emploi

Bulldog Security

Bulldog Security Deluxe 22I Mode d’emploi

Bulldog Security

Bulldog Security DELUXE 12 Mode d’emploi

Bulldog Security

Bulldog Security RS79 Mode d’emploi

Bulldog Security

Bulldog Security DELUXE 12 Manuel utilisateur

Bulldog Security

Bulldog Security RS102 Mode d’emploi

Bulldog Security

Bulldog Security DELUXE 200 Instructions d'installation

Bulldog Security

Bulldog Security RS82P Manuel utilisateur

Bulldog Security

Bulldog Security RS1200 Manuel utilisateur

Bulldog Security

Bulldog Security KE100, KE150, 1702 Manuel utilisateur

Bulldog Security

Bulldog Security Deluxe 62I Mode d’emploi

Manuels Démarreur à distance populaires d'autres marques

AstroStart

AstroStart 803U Manuel utilisateur

Durite

Durite 0-649-20 Manuel

EINHELL

EINHELL BT-PS 1000 Manuel

Linear

Linear ACCESS AK-21 Caractéristiques techniques

Soundstream

Soundstream TARANTULA RS.2 Manuel utilisateur

Jaycar Electronics

Jaycar Electronics MB3752 Manuel utilisateur

Ultra Start

Ultra Start 72 Series Manuel utilisateur

ADS

ADS FLASHLOGIC FLRSVW1 Manuel utilisateur

Selecta

Selecta JS012 Manuel utilisateur

Black Widow Security

Black Widow Security BW RAS 400 Manuel utilisateur

Vector

Vector Power City DK080706 Supplément

Code Alarm

Code Alarm CA-535 Manuel utilisateur

Ozito

Ozito OJS-800 Manuel utilisateur

Profi-Partner

Profi-Partner 46387 Manuel utilisateur

EZ STARTER

EZ STARTER EZ-45 Manuel utilisateur

Viper

Viper 4204 Manuel utilisateur

Essex Electronics

Essex Electronics KE-1701 Manuel utilisateur

EINHELL

EINHELL EGS 3600 Manuel