BSD BSD-9300L Manuel utilisateur

OPERATION AND MAINTENANCE MANUAL

BSD-9300L

BSD-9400L

BSD-9500L

BSD-9300LF

BSD-9400LF

BSD-9300P

BSD-9400P

BSD-9500P

BSD-9300PF

BSD-9400PF

LOW VOLTAGE

METAL ASSEMBLY SCREWDRIVER

KILEWS INDUSTRIAL CO., LTD.

http://www.kilews.com.tw

Y20049-4-002

Metal Assembly Screwdrivers are designed for installing threaded fasteners in light industrial and appliance

manufacturing applications.

KILEWS is not responsible for customer modification of tools for applications on which KILEWS was not

consulted.

Important safety information enclosed.

Read all these instructions before placing tool in service or operation this tool and save these instructions. It is

the responsibility of the employer to place the information in this manual into the hands of the operator. Failure

to observe the following warnings could result in injury. When using electric tools. Basic safety precautions

should always be followed to reduce the risk of fire, electric shock and personal injury, including the following:

1. General Safety Rules

2. Operations Cautions

3. Specifications

4. Description Of Operation

5. Torque Adjustment Operation

6. Accessories

7. Servicing

NOTICE

WARNING

WARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock

fire and/or serious injure. The term “power tool” in all of the warning listed below refer to your mains operated

(corded) power tool or battery operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Electrical Safety

a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.

b) Do not operate power tools in explosive atmosphere, such as in the presence of flammable liquids,

gases or dust. Power tools create sparks which may ignite the dust of fumes.

c) Keep children, and bystanders away while operating a power tool. Distractions can cause you to lose

control.

2) Electrical Safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord to carry, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric

shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of cord

suitable for outdoor use reduces the risk of electric shock .

3) Personal Safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use

power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of

inattention while operating power tools may result in serious personal injury.

b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power

tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d) Remove any adjusting keys or wrench before turning the power tool on. A wrench or a key that is left

attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power

tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from

moving parts. Loose clothes, jewellery, or long hair can be caught in moving parts

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are

connected and properly used. Use of these devices can reduce dust related hazards.

4) Power tool Use and Care

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will

do the job better and safer at the rate for which it was designed.

b) Do not use power tool if switch does not turn it on or off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source before making any adjustments, changing accessories, or

storing the power tools. Such preventive safety measures reduce the risk of starting the power tool

accidentally.

1. General Safety Rules

d) Store idle power tools out of reach of children and do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any

other condition that may affect the power tools operation. If damaged, have the power tool repaired

before use. Many accidents are cause by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tools, accessories and tool bits etc., in accordance with these instructions and in the

manner intended for the particular type of power tool, taking into account the working conditions and

the work to be performed. Use of the power tool for operations different from intended could result in a

hazardous situation.

5) SERVICE

a) Have your power tool serviced by qualified repair person using only identical replacement parts, This

will ensure that the safety of the power tool is maintained.

Additional information shall be provided

a) Instruction for putting into use.

1. Setting-up or fixing power tool in a stable position as appropriate for power tools which can be mounted

on a support.

2. Assembly.

3. Connection to power supply, cabling, fusing, socket type and earthing requirements.

4. Illustrated description of functions.

5. Limitations on ambient conditions.

6. List of contents.

b) Operating Instructions.

1. Setting and testing.

2. Tool changing.

3. Clamping of work.

4. Limits on size of work piece.

5. General instructions for use.

c) Maintenance and servicing.

1. Regular cleaning, maintenance, and lubrication.

2. Servicing by manufacture or agent, list of addresses.

3. List of user-replaceable parts.

4. Special tools which may be required.

1) Whenever changing a bit, make certain the Forward / Reverse Switch is in the “ OFF ”position and tool is

unplugged.

2) Do not allow chemicals such as acetone, benzene, thinner, trichloroethylene ketone, or other similar

chemicals to come in contact with the screwdriver housing as damage will result.

3) Do not drop or abuse the screwdriver.

4) Do not adjust the torque setting higher than 8 on the torque scale.

5) There should be a tool rest interval when cycles three seconds or longer. This tool is intended for a duty

cycle of 0.8 sec on, 2.4 sec off.

6) Do not use this screwdriver for tightening wood screws. This is “ Metal Assembly Screwdriver ”.

7) Do not operate the Forward / Reverse Switch the motor is running.

8) Whenever a tool is not being used, move the Forward / Reverse Switch to the “OFF” position and unplug

the screwdriver.

● Do not drop or abuse the tool.

● Whenever a tool is not being used, position the Power Switch to the “OFF” position and unplug the power

cord.

2. Operations Cautions

CAUTION

REQUIREMENTS

This tool requires an power controller：

BSP-32HL-60W(input：100-240VAC 50/60Hz output：24/32VDC)

BSP-32VR-60W(input：100-240VAC 50/60Hz output：24-32VDC)

MODEL BSD-9300L/P BSD-9400L/P BSD-9500L/P BSD-9300LF/PF BSD-9400LF/PF

Input voltage(DC) 24/32VDC or 24-32VDC

Rated input 55W

Bit torque

(kgf.cm) 6-22 10-30 15-45 5-12 10-30

(Lbf.in) 5.22-19.12 8.67-26.02 13.0-39.02 4.34-10.44 8.67-26.02

(N.m) 0.59-2.16 0.98-2.94 1.47-4.41 0.49-1.18 0.98-2.94

Torque Accuracy (%) ±3%

Torque Adjustment Stepless

Unloaded

Rotation Speed

(R.p.m) ±10%

HI 1000 750 530 2000 1000

LO 700 520 350

Metal

assembly

screw

Machine

screw(mm)

2.6-4.0 3.0-5.0 4.0-6.0 2.0-3.0 3.0-5.0

Tapping

screw(mm) 2.0-3.5 2.6-4.0 3.0-5.0 2.0-2.6 2.6-4.0

·Weight (g) 700

Length (mm) 260

Model of Torque Fixing

Ring

KC-1

Power controller BSP-32HL-60W ；BSP-32VR-60W

Model of Suspension Rack

KH-3 (KC & KH-1)

Bit Type

HEX 5mm HEX 6.35mm

* 1N.m=10.2Kgf.cm 1N.m=8.85Lbf.in

3. Specifications

Attaching / detaching bit and bit type

Push up the holder clamp by fingertip, and it will be unlocked. Thus, the bit can be freely attached and

detached (single finger notion type) select such a bit whose shank is equal to the size shown below.

▓Insert the power plug into a receptacle and set the changeover switch to “F”position.

▓Apply the bit to the screw head and press the lever or push main body to, then the switch will be turned

ON to start the motor running.

▓When the screw is tighten and reach the torque that you had set. The tool will stop automatically.

▓To reset the tool by releasing the lever to the original position or releasing the bit From the screw head.

▓To return the screw, set the changeover switch to “R” position.

To adjust the torque on these screwdrivers. Proceed as follows:

1. Determine the torque output of the tool by checking a tightened Fastener with a torque wrench.

2. Increase or decrease the torque by rotating the Spring Adjusting Ring. Rotating the Ring clockwise to a

higher number on the torque Scale increase torque output while rotating the Ring counterclockwise to a

lower number decreases the torque output.

3. Check the adjustment with a torque wrench. A number of factors will affect torque output from one job to

another. Final torque adjustment should be made at the job through a of series of gradual increase. Always

start below the desired torque and work upward.

4. Adjust the bit torque by changing the driving in length of the adjust ring at the end.

5. The relationship between torque scale and bit torque is as shown Ring, in the torque diagram. The figures

of torque scale do not indicate bit torque values. However, the clamping torque of screw itself is different

form type, size, material of the screw and the material of its mating part. Use it as standard to obtain an

appropriate clamping torque.

6. The (Return torque method) in which once-clamped screw is returned with torque wrench or the like is

available as one of torque control methods, however, note that the measured values by the return torque

method generally appear in 10%~30% lower than the actually clamping torque.

7. The torque checker measures the torque of screwdriver. The clamping torque of screw itself is different

from the clamped conditions. Understand the correlation between clamping torque values and the torque

checker values perform the torque control properly.

4. Description of Operation

5. Torque Adjustment Operation

1. Also in reverse rotation, the clutch is turned off in such manner as in normal rotation, stopping the motor

running. Accordingly, when the screw tightened at a large torque, set it to a higher torque scale.

2. The number from zero to eight on the Torque Scale are reference number only and not an indication of

actual torque output.

1. BIT Type ：No. 00 ．．．．Bit use in dia 1.3-1.8mm screw

No. 0．．．．．Bit use in dia 1.6-2.0mm screw

No. 1．．．．．Bit use in dia 2.0-2.6mm screw

No. 2．．．．．Bit use in dia 3.0-4.0mm screw

BSD-9300L/P with BIT 1# & 2# 1 Pce. Each

BSD-9400L/P with BIT 2# 2 Pce.

BSD-9500L/P with BIT 2# 2 Pce.

BSD-9300LF/PF with BIT 1# & 2# 1 Pce. Each

BSD-9400LF/PF with BIT 2# 2 Pce.

2. Carbon Brush :2 Pcs, those 2 Pcs brush are spare parts.

3. Suspension rack and Torque fixing ring acceptable for use with the tool are available from KILEWS

catalogue.

6. Accessories

CAUTION

Maintenance and Inspection:

1. The screwdriver must be operated in top condition. one day working hour must be not more than eight

hours.

2. Periodically check for wear of motor carbon brush, one day for eight hours use is normal, replace it after

every five to six months.

3. Please note don’t let the motor get over heated, every minute use 10~15 screws to operate.

4. The frequency use of this electric screwdriver is over than eight hours a day, still it needs periodically

testing and treatment. Every 5-6 months.

5. Inspect tool cords periodically and if damaged, have them repaired by an authorized service facility.

Inspect extension cords periodically and replace if damaged.

6. Do not remove any labels. Replace any damaged label.

1. The use of other than genuine KILEWS replacement parts may Result in decreased tool performance and

increased maintenance and may invalidate all warranties.

2. All repairs and maintenance of this tool and its word must be performed by an authorized service center.

3. KILEWS is not responsible for customer modification of tools for applications on which KILEWS was not

consulted.

4. Repairs should be made only by authorized, trained personnel. Consult your nearest KILEWS authorized

service center.

5. It is the responsibility of the employer to place the information in this manual into the hands of the

operator.

DO NOT ATTEMPT TO REPAIR THIS

ELECTRIC SCREWDRIVER

SAVE THESE INSTRUCTIONS

DO NOT DESTROY

7. Servicing

CAUTION

CUSTOMER

ITEM NO:

TITLE:

DWG NAME

MATERIAL

DES. BY

CHKD.BY

APPD.BY

SHRINK

DATE

PRODUCTION NO.

THIRD ANGLE PROJECTION.

UNITSCALESHT NO.

OF SHTS.

MODEL:

BSD-9300L

BSD-9400L

BSD-9500L

BSD-9400LF

DWG NO:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels BSD Tournevis électrique

BSD

BSD TKS-1300 Manuel utilisateur

Manuels Tournevis électrique populaires d'autres marques

Makita

Makita DFT085F Manuel utilisateur

Parkside

Parkside 345138 2004 Manuel utilisateur

Makita

Makita DFL650F Manuel utilisateur

AEG

AEG BST 18BLX2-0 Manuel utilisateur

Ingersoll-Rand

Ingersoll-Rand D5000 Series Manuel utilisateur

BGS technic

BGS technic 956 Manuel utilisateur

Hilti

Hilti SD 6000 Manuel utilisateur

Parkside

Parkside PEPS 3 A1 Manuel utilisateur

Festool

Festool TI 15 Manuel utilisateur

Makita

Makita DWT190 Manuel utilisateur

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Manuel utilisateur

Skil

Skil 2346 Instructions de montage

DeWalt

DeWalt XR LI-ION DCD931 Manuel utilisateur

Festool

Festool DWC 18-2500 Manuel utilisateur

EINHELL

EINHELL TE-CD 12/1 Li Series Manuel utilisateur

Makita

Makita BFT043F Manuel utilisateur

Stanley

Stanley SCD2 Manuel utilisateur

Atlas Copco

Atlas Copco LUM12 SR Feuille d'instructions