Bruno VPL-3100 Manuel utilisateur

MAN-3100-1

06-02-2008

1780 EXECUTIVE DR., P.O. BOX 84, OCONOMOWOC, WI 53066 USA

TELEPHONE:(262) 567-4990

FAX: (262) 953-5501

1-800-882-8183

DEALER: INSTALLATION MANUAL

VPL-3100

Technical Service email: [email protected]

www.bruno.com

VERTICAL PLATFORM

LIFT

• Check for shipping damage immediately upon receipt. Contact

the shipper with any damage claims.

• Check the contents against the packing list before leaving the

shop to begin on-site installation. Immediately report any

discrepancies to Bruno Independent Living Aids, Inc.®.

Read and understand the installation manual prior to proceeding

with the installation.

Throughout this manual, safety precautions are provided

to identify potentially hazardous situations and to advise how to

avoid them.

Warning– Indicates a potentially hazardous situation

that, if not avoided, could cause serious bodily

injury and / or property damage.

Caution–Indicates a potentially hazardous situation

that, if not avoided, could cause damage to the

unit and / or moderate injury.

Electrical Hazard–Indicates a potentially hazardous

electrical situation that, if not avoided,

could cause damage to the unit and /

or moderate injury.

Lubriplate® is a registered trademark of Lubriplate Division (Fiske Brothers).

Vise-Grip® is a registered trademark of Petersen Manufacturing Co.

VPL-3100 06-02-2008

TABLE OF CONTENTS

Specications ........................................... 4

Tools ................................................. 5

Safety................................................. 6

Pre-Installation Checks ................................. 7-8

Installation

Main component .....................................9-10

Adjusting top landing/nal limit switches ..................... 11

Standard gate installation .............................12-14

Cam/actuator installation and adjustment (standard gate) .......15-16

Wide gate installation ................................17-19

Cam/actuator installation and adjustment (wide gate) ..........20-21

Wiring the call/send and gate ...........................23-24

Mounting the call/send box .............................16-17

Securing the unit ...................................... 25

Testing ............................................. 25

Completing the installation ............................... 26

Moving the ramp, ramp actuator and vertical bar to the opposite side .27-31

Optional gate interlock installation .........................32-33

Optional electric door interlock installation ...................34-35

Emergency and cold-weather operation ........................ 36

Troubleshooting .......................................37-38

Wiring schematic ......................................39-40

Exploded views and drawings .............................41-53

Warranty.............................................. 54

SPECIFICATIONS

Load Capacity 750 lbs. (340 kg)

Weight of Unit

VPL-3153 752 lbs. (341 kg)

VPL-3175 825 (374 kg)

Rated Speed 9 FPM (2.75 m/mn)

Power Supply 120 VAC, 15A, single phase, 60 Hz

Motor 1 HP, 120 VAC

Control Voltage 24 VAC, motor 120 VAC

Maximum Travel 53” (1.3 m) unit and 75” (1.9 m) unit

Platform Size standard: 34” x 48” (86 x 122 cm); optional: 34” x 54”

(86 x 137 cm)

Emergency Operation provision for manual hand wheel

Standard Features keyed, constant-pressure controls on platform with

emergency stop switch; all-weather protected controls

and switches; platform bottom safety panel, top and

bottom limit switches, automatic folding ramp

Optional Features landing call/send station with key; top landing gate

including call/send station with key and Bruno interlock;

34”x54” non-skid platform

Recommended Bolt Torque

Size Recommended Torque

Grade 5 Grade 8 18-8 S/S

Coarse Fine Coarse Fine Coarse Fine

1/4 8 10 12 14 6.3 7.8

5/16 17 19 24 27 11 11.8

3/8 31 35 44 49 20 22

7/16 49 55 70 78 31 33

1/2 75 85 105 120 43 45

9/16 110 120 155 170 57 63

5/8 150 170 284 323 93 104

3/4 270 295 510 568 128 124

Units are ft.-lbs.

These torque values are provided for

reference only. If specic torque is

required for an installation operation, it

will be indicated.

VPL-3100 06-02-2008

Tools Needed for Installation

TOOLS

• 1/2” dia. x 3” lg. masonry anchors

• Sawzall® or similar reciprocating saw

• Circular saw

• Straight and Phillips screwdrivers (or bits)

• Combination wrench sets (SAE)

• Allen wrench set (SAE)

• Socket wrench set (SAE)

• Level (4-foot) or inclinometer

• Torque wrench (20 lb.-ft to 133 lb.-ft) low-prole,

open-end wrench style preferred

• Voltohmmeter and probes

• Wire stripper

• Crimping tool

• Tape measure

• Pry bar

• Hammer and mallets

• Extension cord for power tools (50’ minimum)

• Vise-Grips®

• Appliance dolly

• Hammer drill

• Masonry bits, 1/2” and 3/8”

• Reversible drill, 3/8”, and bits

• File

• Hammer drill, 1/2” for concrete fasteners

• Never exceed the maximum rated lift

capacity of 750 lbs. (340 kg).

• Never use the VPL-3100 to lift freight or

other materials than intended by design.

• Read and understand the installation

manual prior to installing the VPL-3100.

• Wear appropriate safety protection equip-

ment for your head, eyes, hands and feet

during all phases of the installation.

• Lift components are heavy. Use extreme

caution when lifting them to the installa-

tion position to avoid personal injury and

damage to the equipment.

• Keep panels and protective coverings in

place to avoid potentially fatal injury.

• Disconnect power from the unit before

performing any electrical or mechanical

service operations.

• Never bypass sensor switches which prevent

accidental start up when protective panels

are removed.

• Do not work alone.

• Be aware of the location of others in the

work zone.

• Do not wear jewelry or loose clothing.

• Lock the wheels of any mobility device

riding on the platform.

• Use only recommended anchor fasteners.

• Check for applicable local codes and

regulations.

• Failure to comply with the above could

render the warranty nulL and void.

RISK OF

ELECTROCUTION

AND

DEATH

WARNING

Remove all metal

jewelry (rings, bracelets

etc.) which might

accidentally come in

contact with an

electrical terminal.

SAFETY

There are no USER

serviceable parts in

the electrical box.

VPL-3100 06-02-2008

• Visit the installation site.

• Verify that a dedicated 15A electrical circuit

is available for installation of the VPL-3100

and that it has been installed by a qualied

electrical contractor in compliance with local

codes and regulations.

• Check for correct voltage and supply wire

size.

• Conrm the structural integrity of the fascia.

• Conrm the existence of a properly constructed

concrete base that is level and at.

• Verify that the walls and oors are level.

• Verify hoistway clearances, nished openings

for gates and doors, ceiling break clearances

and electrical layout.

• Locate and eliminate possible pinch points.

• Determine the path to be used to move the

unit into place. Make sure it is free of obstacles.

• Double-check the order form to verify receipt

of all parts needed for installation.

• Make sure that the ramp and the ramp actua-

tor are on the correct side (right or left) for

the installation.

To move the ramp/ramp actuator to the

opposite side, see “MOVING THE RAMP AND

RAMP ACTUATOR TO THE OPPOSITE SIDE”

appearing later in this manual.

PRIOR TO INSTALLATION

A solid foundation is key

to a successful

installation.

Never install the

VPL-3100 on an asphalt

driveway, patio stones,

concrete blocks or other

unstable surfaces.

PRE-INSTALLATION CHECKS

The fascia must be

smooth, vertical and

structurally sound.

Check all applicable

local codes.

• VSL-3175

The VSL-3175 is shipped disassembled.

Prior to installation, mount the platform to

the tower.

1. From the platform, remove the vertical

panel with the pushbutton controls.

2. Move the platform into position next to the

tower.

NOTE: A skate dolly works well for this purpose.

3. Attach the platform to the tower using the

bolts, washers, lockwashers and nuts

provided.

4. Remount the vertical panel with the

pushbutton controls.

PRIOR TO INSTALLATION

(continued)

PRE-INSTALLATION CHECKS

VPL-3100 06-02-2008

INSTALLATION

The VPL-3100 must be installed on a level,

smooth concrete base with a minimum thick-

ness of 4” (10 cm), in place prior to installa-

tion and not provided by Bruno.

1. Decide on which side of the unit the call/

send and gate wire harnesses will be routed.

This is easier to do before placing the unit in

the installation position.

2. Place the VPL-3100 in its approximate nal

position on the concrete base.

3. Align the platform to the opening provided at

the top landing for exiting the VPL.

4. Connect the VPL-3100 power cord to the

dedicated power source (provided by others

and in place prior to installation).

5. Test operation of the VPL-3100 using the

platform control.

6. Verify that the unit is plumb, side-to-side

and front-to-back. Shim base if necessary.

NOTE: Align the shims (provided-see left) with

the mounting holes to keep the shims in

place when fasteners are inserted.

7. If the height of the unit was ordered based on

a specic installation, run the platform to the

top landing.

Otherwise, skip to the next step.

8. Run the unit up until it stops at the factory-

set maximum height.

9. Measure from the platform to the top of the

landing. If the landing is above the plat-

form, you will measure this number of inches

ABOVE the mark placed on the channel at the

factory, near the limit switch. If the landing is

below the platform, you will measure BELOW

the mark.

INSTALLATION OF MAIN COMPONENT

Per ASME Code

A18.1, there must be

a clearance of 3/8”

to 3/4” (10 mm to

19 mm) between

the platform and the

fascia.

shim

INSTALLATION

NOTE: Steps 10—14 may have been done

when the unit was removed from the ship-

ping pallet. If so, proceed to the next section.

10. Loosen but do not remove the (3) screws

at the bottom of the front panel.

11. Loosen the (2) screws on each side of the

top cover.

12. Slide the top cover up and off.

13. Remove the (3) screw along the top of the

front access panel.

14. Slide the front access panel up and off.

Set to the side.

NOTE: Removal of the top cap opens the top

housing sensor switch. This

prevents accidental movement of the

platform. See left and below.

15. ALWAYS replace the top cover after com-

pletion of installation/service operations.

Top Cover Safety Switch

This is a push-pull switch.

When the top cap is in place,

the switch is closed, permitting

the unit to operate normally.

When the top cover is

removed, the switch is open,

and the unit will not operate.

DURING INSTALLATION

AND SERVICE WORK ONLY,

enable unit operation by

pulling up on the switch until it

snaps into position.

Remounting and securing the

top cover pushes the switch

down to its normal operating

position.

pull up for service

with top cover in

place, switch is

pushed down and

unit operates.

with top cover

removed, switch is

in middle position

and unit will not

operate

Moving parts can

crush and cut.

Use extreme caution

around open drive

components when

switch is up.

Table des matières

Autres manuels Bruno Système de levage

Bruno

Bruno OUTDOOR ELITE CRE-2110E Manuel utilisateur

Bruno

Bruno JOEY VSL-4400 Manuel utilisateur

Bruno

Bruno ELECTRA-RIDE SRE-1540 Guide de maintenance et de service

Bruno

Bruno VPL-3100B Manuel utilisateur

Bruno

Bruno CRE-2110 Manuel utilisateur

Bruno

Bruno CURB-SIDER VSL-6000G Manuel utilisateur

Bruno

Bruno JOEY VSL-4400G Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur