Brother BAS-416 Manuel utilisateur
Page 1 of 3
An increased resistance that makes it either hard or impossible for the main motor to turn the
degree wheel or pulley causing a motor lock error. Listed below are some causes of the
problem. Listed in the order that they occur most.
Lack of Lubrication
• Oil the machine as specified under initial unpacking procedure. Make sure and oil the
rotary hook.
Thread tangled in rotary hook
• Open bobbin case cover and look for thread tangled in the rotary hook around it or
behind it and remove thread. Rotate pulley back to stop position after finished. This
can be caused by bird’s nest, which is created by various things. Such as
• Incorrect threading of machine
• Incorrect needle size or type of needle for application
• Needle being installed backwards
• Worn needles
• Incorrect backing for the application.
• Loose upper thread tension
• Inner rotary hook adjuster set incorrectly
Foreign object stuck in the rotary hook
To check if something is causing binding in the rotary hook see if you can
move the bobbin basket clockwise and counter-clockwise. The bobbin
basket is part of the rotary hook. This is part that the bobbin case fits into.
To check the play put two fingers on the bobbin case latch and rotate your
fingers in both directions. You should have a little play in both directions. If
not then there is something lodged in the raceway of the rotary hook. Clear
obstruction or replace rotary hook. This can be caused by
• Broken pieces of needle lodged somewhere in hook
• Thread badly entangled in rotary hook.
Rotary Hook
Check for broken bits of
needles in this area.
Motor Locks – Causes and Solutions
For Technical Assistance Please Call Toll Free 1-877-4BROTHER
Page 2 of 3
A buildup of thread is behind the moving knife
o Remove needle plate and remove the thread build up behind the moving and fixed
knife. This build up is causing the moving knife not to be able to complete its cycle
Needle hitting presser foot
o Adjust presser foot so that is aligned with the hole in the
needle plate.
o Replace bent presser foot and adjust presser foot height.
o Replace bent needle.
Needle hitting needle plate
o Adjust the alignment of the needle plate. Rotate pulley to
150 degrees and see if needle goes through the middle of the
hole in the needle plate. If not, loosen the two screws that
hold on the plate and move the plate to align with needle
and retighten screws. Turn pulley backwards to stop position
(100 degrees).
Needle hit the hoop while sewing
o Loosen the needle holding setscrew of the needle that is stuck in the hoop. Rotate the
pulley to bring the needle up. Remove hoop from machine and turn pulley back to
stop position (100 degrees). Remove needle from hoop with pliers.
Moving knife is not at proper position
o Remove needle plate and check position of
moving knife. If knife is out of position try
manually moving it back into position with
your fingers. Cycle the trimmer with the
button on the keypad and recheck
adjustment.
Motor Locks – Causes and Solutions
For Technical Assistance Please Call Toll Free 1-877-4BROTHER
Page 3 of 3
Moving knife is out of adjustment
o Before adjusting moving knife check the fixed
knife to see if it is 10mm from the needle and
against the pin. Usually if the fixed knife is
pushed all the way back against its adjustment
slot that is approximately 10mm. If needed
adjust clearance of moving knife to 1.2 mm.
You will need to remove the chrome are cover
to gain access to the adjustment bolts.
Inner rotary hook adjuster set incorrectly
• Check clearance of inner rotary hook stopper,
also known as the positioning finger. It may be in to
far causing thread to wrap around it.
Thread take up lever striking the needle case cover
o Adjust thread take up driving lever so that all take up levers are even. Make sure this
is done at stop position (100 degrees). You will need to remove the tension base to
gain access to the adjustment bolt.
Needle depth or 0 degree stopper out of position
o Adjust needle depth first and then 0 degree stopper. Please refer to your instruction
manual for adjustment.
Motor Locks – Causes and Solutions
For Technical Assistance Please Call Toll Free 1-877-4BROTHER
Autres manuels pour BAS-416
9
Ce manuel convient aux modèles suivants
18
Table des matières
Autres manuels Brother Machine à coudre
Brother
Brother DA-9270 Manuel utilisateur
Brother
Brother Innov-is 2500D Mode d’emploi
Brother
Brother LK3-B430E Manuel utilisateur
Brother
Brother LZ2-B856E Manuel utilisateur
Brother
Brother XL-5500 Manuel utilisateur
Brother
Brother S-7300A Manuel utilisateur
Brother
Brother LS-2125i Manuel utilisateur
Brother
Brother SCANNERII Guide de dépannage
Brother
Brother BE-0901E PC Manuel utilisateur
Brother
Brother BAS-416 Manuel
Brother
Brother Duetta 4500D Instructions de montage
Brother
Brother CS-6000i Manuel utilisateur
Brother
Brother XL-3010 Manuel utilisateur
Brother
Brother 2340CV Manuel utilisateur
Brother
Brother Innov-is NV4000D Manuel utilisateur
Brother
Brother NV10 Manuel utilisateur
Brother
Brother XC4953-021 Manuel utilisateur
Brother
Brother Innov-is 900D Manuel utilisateur
Brother
Brother BA-15 Manuel utilisateur
Brother
Brother PQ-1300 Manuel utilisateur
