Brightline I-Series Guide de démarrage rapide

i-Series Videoconference Fixture

Operation and Installation Guide

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

Safety

Owner’s Record

Product Description

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

To prevent risk of fire or electric shock, do not expose this fixture to water or moisture. i-Series fixtures are

listed for indoor use only.

Do not open fixtures, as this may damage internal components and will void the warranty.

The model number for this product can be found on top of the power supply. You should note the model

number in the space provided and retain this book for future reference as a permanent record of your

purchase.

Model No.

Date of Purchase

i-Series Fixture

The i-Series, a sleek, cool-to-the-touch, energy efficient LED fixture, is scalable to virtually any monitor or

display. The i-Series fixtures make it easy to look your best on camera, allowing individuals to conference

remotely without sacrificing critical visual details.

i-S/48/D

i-S/48

i-S/36

i-S/22

i-S/16

Specifications

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

Housing:

.078” thick aluminum extrusion, aluminum cast end caps.

Reflector:

.09” aluminum reflector, powder-coated gloss-white.

Finish:

Fixture body and end caps are painted with a smooth, gloss-black powder-coating.

Transformer:

A low-voltage transformer with a 6-foot power cord. The plug is a NEMA 1/15P (single pin

connection). Input: 100-240 VAC 50/60Hz

Lamp:

LED - Warm white. 3200K - 50,000 hours

Optional Accessories:

VESA mounting bracket plate in 75mm - 100mm, 100mm-200mm sizes (i-S/16 and i-S/22 only)

VESA large pattern brackets

Dimensions:

Overall body dimensions are:

i-S/16: 16” x 1.71” x 3.5” (406.4mm x 43.44mm x 88.9mm)

i-S/22: 22” x 1.71” x 3.5” (558.8mm x 43.44mm x 88.9mm)

i-S/36: 36” x 1.71” x 3.5” (914.4mm x 43.44mm x 88.9mm)

i-S/48: 48” x 1.71” x 3.5” (1219.2mm x 43.44mm x 88.9mm)

i-S/48/D: 48” x 3.21“ x 3.5” (1219.2mm x 81.54mm x 88.9mm)

Labels:

CE, UL, cUL, CCC, and PSE certifications pending. Patent pending.

Installation - Small Pattern VESA

ATTACHING VESA PLATE TO MONITOR

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

Unpack the fixture.

Locate the VESA plate and mounting screws.

On the reverse of the monitor, locate the VESA mounting pattern (figure 1).

Align VESA plate to mounting pattern. Use provided screws to attach the VESA plate to the monitor.

Make sure that the attached VESA bracket angle is facing away from the monitor and that it is

oriented to achieve the desired fixture position (figure 2).

NOTE: Flip VESA bracket for additional height options

Figure 1 - 100mm VESA pattern shown

Figure 2 - Attaching VESA plate to monitor

Installation - Small Pattern VESA

ATTACHING THE FLEX ARM

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

Using the bracket angle, the provided screw, and

the provided Allen wrench, attach the flex arm to

the bracket angle as shown (figure 3).

ATTACHING THE FIXTURE

Attach to the fixture to the flex arm with the

provided screw. Secure through bracket on the

back of the fixture (figure 4).

Figure 3 - Attaching the flex arm to the VESA plate

Figure 4 - Attaching the fixture to the flex arm

Installation - Large Pattern VESA

ATTACHING FLEX ARMS TO BRACKETS

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

It’s strongly recommended that you attach the

flex arms to the brackets before attempting any

installation. You can use the top of the flex arm to

guage the approximate location of the fixture

when adjusting the height on the brackets.

Note the dimensions in figure 7 when positioning

the brackets. If the top flange of the bracket falls

below 6” under the top of the display, there may

be interference with the i-Series fixture. To

achieve the best possible user experience, install

the brackets so that 1” to 3” of the flex arm are

exposed above the display. This will provide the

best possible articulation (figure 5).

Locate the flex arms, brackets and hex head

screws.

Use the provided Allen wrench to attach each

flex arm to a bracket.

Insert, but do not over tighten, the remaining

hex head screws into the top of both flex

arms.

Figure 6 - Assembling the bracket and flex armFigure 5 - Recommended Height Figure 7 - Bracket dimensions

6.18”

14.13”

1“ - 3”

Installation - Large Pattern VESA

INSTALLING BRACKETS WITH AVAILABLE VESA HOLES

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

If your display has multiple VESA patterns (e.g., 400x600 &

400x800) or if your display is not wall-mounted, you may

mount the i-Series brackets to the unused holes without

uninstalling your existing VESA bracket (if applicable).

Unpack fixture and and accessories.

Unmount your display (If necessary) and place face-down on a clean, soft surface.

If your display takes size M6 screws, use the M6x12mm screws to mount the brackets. If your display takes

size M8, use the M8x16mm screws. When using the M6, you must also use the metal washer (figure 8).

Take two (2) nylon washers and align them with the topmost unused holes. They should be evenly spaced

from the center (figure 9). If you have more than one set available, use the widest set.

Position bracket with flat side facing display. Align appropriate slot with the hole depending on your

height requirement (figure 10). Use only the top five (5) slots.

Secure with screws provided. Ensure brackets are parallel before tightening. If your mounting hole is too

shallow, insert another nylon washer (figure 11). Add only as many as you need. Screw should be as deep

as possible.

Figure 8 - LEFT: M8 - RIGHT: M6 with washer

Figure 9 - Components in line with mount holes

Figure 10 - Adjusting height of bracket

Figure 11 - Additional washer

Installation - Large Pattern VESA

INSTALLING BRACKETS WITH EXISTING VESA BRACKETS

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

If your display has only one VESA pattern and it

is in use by an existing VESA bracket, you may

install the i-Series bracket one of two ways. If the

VESA bracket is wide enough and there is no

interference with the mounting apparatus

(figure 12), then the i-Series bracket can nest

within the VESA bracket. If the VESA bracket is

too narrow or too shallow or otherwise incom-

patiple with this method, please see page 3.

Unpack fixture and and accessories.

Unmount your display (If necessary) and place face-down on a clean, soft surface.

If your display takes size M6 screws, use the M6x16mm screws to mount the brackets. If your display takes

size M8, use the M8x20mm screws. When using the M6, you must also use the metal washer (figure 13). If

the screws used to install your VESA brackets are longer than our provided size, you may reuse them.

Remove all screws used to install your VESA bracket. Separate them from the screws provided with the

i-Series bracket.

Take four (4) nylon washers and align them with the VESA holes (figure 14).

Reposition VESA brackets on top of nylon washers. Position i-Series brackets in VESA brackets with flat

side facing display. Align appropriate slot with the topmost hole depending on your height requirement

(figure 15). Use only the top five (5) slots.

Secure VESA bracket and i-Series bracket with screws provided. Ensure brackets are parallel before tight-

ening. If your mounting hole is too shallow, insert another nylon washer for each screw (figure 16). Add

only as many as you need. Screw should be as deep as possible.

Figure 13 - LEFT: M8 - RIGHT: M6 with washer

Figure 14 - Components in line with mount holes

Figure 15 - Adjusting height of bracket

Figure 16 - Additional washer

Figure 12 - i-Series

bracket nested inside

VESA bracket : no interference

.4375”

Installation - Large Pattern VESA

INSTALLING BRACKETS WITH EXISTING VESA BRACKETS (PART 2)

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

If your display has only one VESA pattern and it

is in use by an existing VESA bracket, you may

install the i-Series bracket one of two ways. If the

VESA bracket is too narrow to nest the i-Series

bracket inside it or if the mounting aparatus

would interfere with the i-Series bracket if

nested, you may mount the bracket between the

VESA brackets and the display.

Unpack fixture and and accessories.

Unmount your display (if necessary) and place face-down on a clean, soft surface.

Take i-Series bracket and snap off lower portion on each (figure 17). Do not discard either portion.

If your display takes size M6 screws, use the M6x25mm screws to mount the brackets. If your display takes

size M8, use the M8x30mm screws. When using the M6, you must also use the metal washer (figure 18). If

the screws used to install your VESA brackets are longer than our provided size, you may reuse them.

Remove all screws used to install your VESA bracket. Separate them from the screws provided with the

i-Series bracket.

Take four (4) nylon washers and align them with the VESA holes (figure 19).

Position i-Series brackets with flat side facing display. Align appropriate slot with the topmost hole

depending on your height requirement (figure 20). Use only the top five (5) slots. Use the smaller,

snapped-off portion as a shim on the lower holes.

Reposition VESA brackets on top of i-Series brackets. Make sure the VESA bracket is fully supported by

both the i-Series bracket and the shim.

Secure with screws provided. Ensure brackets are parallel before tightening. If your mounting hole is too

shallow, insert another nylon washer for each screw (figure 21). Add only as many as you need. Screw

should be as deep as possible.

Figure 18 - LEFT: M8 - RIGHT: M6 with washer

Figure 19 - Components in line with mount holes

Figure 20 - Adjusting height of bracket

Figure 21 - Additional washer

Figure 17 - Bend back and

forth to snap off

Installation - Wall

INSTALLING BRACKETS TO WALL BEHIND DISPLAY

580 Mayer Street, Building #7, Bridgeville, PA 15017 • Phone: 412.206.0106 • Fax: 412.206.0146

When you are unable or unwilling to use any of the VESA mount

options, you may also mount the brackets to a wall behind the

display. Brightline does not provide any hardware for wall-

mounting your i-Series brackets. It is recommended that you

consult with a professional regarding the correct type of

hardware to suit your needs. Make sure your hardware will fit.

Unpack fixture and and accessories.

Mount your display, if it is not already mounted, and mark its top edge on the wall behind it. Use a tape

measure to find the center line. Unmount your display and put aside in a safe place.

Place one i-Series bracket against wall with round flange facing up and position to your preference. This

flange shoud be no lower than 5” below the line indicating the top of the display (figure 22).

Mark the two slots indicated in figure 23 and mark a line indicating the top flange of the bracket. Measure

the distance from the center.

Repeat for the other bracket, using the line you marked for the top flange as a reference. Brackets must

be no less than 20” apart for the I-36 and the I-46. Brackets must be no more than 32” apart for the I-36

and no more than 44” apart for the I-48 (figure 3).

Install bracket hardware as determined by what type of surface to which you are mounting.

NOTE: With wall mounting, you will need to bend the goosenecks forward so that the power connector

does not press into the wall when plugged in. This is normal. Typical large display i-Series installations

require that the fixture is bent forward to illuminate the target as best as possible.

Figure 22 - Adjusting height Figure 24 - Maximum mounting distance

5.00” I-36: MAX 32”

I-48: MAX 44”

Figure 23 - Mounting Bracket

.75”

.34”

1.10”

USE THESE SLOTS

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Brightline Système de conférence

Brightline

Brightline Stealth-T Guide de démarrage rapide

Manuels Système de conférence populaires d'autres marques

Kramer

Kramer VIA GO Manuel utilisateur

AVT

AVT MAGIC AC1 Go Manuel utilisateur

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuel utilisateur

Sony

Sony PCS-I150 Manuel utilisateur

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuel utilisateur

Prentke Romich Company

Prentke Romich Company Vanguard Plus Mode d’emploi

Speakerbus

Speakerbus iD 712 Manuel utilisateur

Trelleborg

Trelleborg SafePilot CAT PRO Manuel utilisateur

Sennheiser

Sennheiser ADN Manuel utilisateur

ADTRAN

ADTRAN NetVanta 7100 Manuel utilisateur

AINA

AINA PTT Voice Responder Manuel utilisateur

Yamaha

Yamaha ProjectPhone PJP-100H Manuel utilisateur

vissonic

vissonic VLI Series Manuel utilisateur

Panasonic

Panasonic KX-VC500 Manuel utilisateur

Poly

Poly Trio 8300 Manuel utilisateur

Crestron

Crestron Mercury CCS-UCA-SMK Dessin dimensionnel

Inmarsat

Inmarsat mini M Manuel utilisateur

Tenveo

Tenveo ALL-IN-ONE Manuel utilisateur

Brightline i-Series Guide de démarrage rapide

Manuels Système de conférence populaires d'autres marques