Brice 590XEC Manuel utilisateur

The 590XEC Two-speed Electric Can Opener is the fast, efﬁcient

and tireless way to open all sorts of cans in busy kitchens.

• Two speed operation

Avoid mess and spills. Switch located on

top of unit for easy access.

• Hardened Steel blade

Fully reversible for double the life.

• Opens a huge range of cans

From 50mm to 270mm.

• Stainless steel construction

For maximum durability and easy cleaning.

• Removable opening head

Opening head unit can be removed without

tools.

• Gas strut assisted action

Raise and lower the motor and opening

assembly effortlessly.

• Sturdy base plate

Strong, stable surface able to handle even

heavy cans.

• Output up to 400 cans continuous use

• Can turning disc available

• Available in 1 or 3 Phase

Two-speed

Electric Can Opener

Model 590XEC Brochure/Manual

Heavy Duty; Manual operation

Speciﬁcations

Motor: Two-speed, 240V single phase

– 50Hz / 60Hz

Power: 75W

Height with the lever up right: 750mm

Width: 300mm

Depth: 300mm

Net weight: 32kg

IP: 55

Assembly Instructions

Position the guide bar at the rear of the

stainless steel base plate and secure with

the supplied nuts and bolts (1).

2. Position the gas strut (2) behind the guide

bar and secure the strut arm to the base

plate with the supplied nut. Note that the

narrowest part of the strut is down.

3. Position the guide channel on the back

of the motor unit onto the guide bar, and

ﬁt the other end of the gas strut into the

small hole provided at the top and back

of the guide channel. Secure the gas strut

using the domed nut provided. Tighten the

knurled knob (3) on the side of the guide

channel to lock the motor unit in place.

4. Loosen the handle securing thumbscrew

on the right side of the opening head (as

you face the machine) and insert the end of

the opening handle, ﬂat side facing inwards

(5). Tighten the thumbscrew to secure the

handle.

5. Fit the two supplied guide handles (A) to

either side of the guide channel behind the

motor unit. Tighten ﬁrmly.

The machine is now ready to operate.

Removal of opening head and other

components for cleaning

Using and maintaining the 590XEC Can Opener

The opening head assembly is secured by a

stainless steel pin at the top and back of the

opening head/cog drive assembly, and by a

knurled steel knob.

To remove the entire opening assembly,

proceed as follows:

1. For ease of access, remove the handle by

undoing the thumbscrew.

2. With one hand underneath the opening

head to support it, draw out the stain-less

steel pin (B) from the right side of the

handle hinge (as you face the machine).

The hinge also holds the blade assembly.

The pin can be quite awkward to get to,

so it may help to push on the head of the

securing pin from the left side of the hinge

assembly.

NB: To prevent the accidental loss of the

securing pin, replace it in position while the

opening head is being cleaned.

3. Lift the hinge assembly away from the

machine.

4. With one hand under the opening head to

support it, locate the large knurled steel

knob (A) behind the opening head assembly

and completely undo it. The opening head

will drop down into your hand.

5. Clean the components using a mild

dishwashing detergent.

6. Reﬁtting is the reverse of removal

The cog drive assembly may be removed

independently, and without removing any other

components, by following the instructions from

point 4, above.

Replacing the Cog Wheel

1. With the opening head assembly in place

on the machine, use the keyed wrench

supplied by locating the two pins on the

wrench in the holes on the underside of the

cog wheel.

2. Supporting the wrench to prevent it falling

away, strike the handle of the wrench to

loosen the cog wheel. Unscrew the cog by

hand. It unscrews in a clockwise direction.

3. Reﬁtting is the reverse of removal, but note

that the lettering and direction arrow on the

replacement cog must face down.

Replacing the Blade

1. Using a screwdriver, undo the blade

securing screw, remove it, the steel washer

and the elastic buffer ring.

2. The blade is reversible so, if only one side

is worn, simply reverse the blade, reﬁt the

screw, washer and buffer and tighten.

3. If replacing the blade, ﬁt the new blade,

together with a new screw, washer and

buffer supplied in the blade replacement

kit. Tighten to secure.

Operating instructions

NB: The can opener can only be operated

with two hands.

1. Position the can on the base plate so that

the edge of the can is below the guide stop

(A).

2. Using the guide handles (B), draw the

motor unit down until the guide stop

contacts the crimped can seal.

3. Clamp the motor head in position by ﬁrmly

tightening the clamping knob (C).

These three steps must be repeated each

time a different height can is opened.

4. Reposition the can under the opening head

so that the can seal is between the blade

and the cog wheel

5. Grasping the opening handle ﬁrmly, draw

it down to force the blade to pierce the tin.

This will also force the lip of the tin against

the cog wheel.

6. Keep pressure on the opening handle and

operate the speed switch. Hold the switch

in position until the lid is completely cut

through.

The speed you select will depend upon

the type and contents of the tin. Speed

1 is best for high ﬂuid content products

that are likely to spill or splash (e.g. tinned

pineapple pieces in syrup). Speed 2 is

better suited to heavy soups and similar.

Cleaning & Maintenance

1. All components of the can opener are easily

disassembled for cleaning.

2. Clean daily with a damp sponge.

3. Never immerse the can opener in water

or put in dishwasher.

4. Regularly brush the blade with a brush to

remove any remnants.

5. To clean behind the cog wheel or to replace

when worn, unscrew the front blade cover,

gently clamp the cog wheel and rotate

handle in an anti-clockwise direction.

Gently brush the area to remove any food

product.

NB:Never sharpen the blade, reverse or

replace the blade when blunt.

BA028.590XEC 5/17

BRICE HEAD OFFICE:

11 Holloway Drive,

Bayswater, Victoria 3153 Australia

Ph: 1300 664 880

www.briceaust.com.au

email: [email protected]

Brice Australia Pty. Ltd. ABN 71 413 589 669

100% Australian owned and operated

Autres manuels Brice ouvre-boîte

Brice

Brice 540N Manuel utilisateur

Manuels ouvre-boîte populaires d'autres marques

Clatronic

Clatronic DO 2852 Caractéristiques techniques

Coopers

Coopers Can Magic Manuel utilisateur

Black & Decker

Black & Decker LIDS OFF JW260 Instructions d'installation

Oster

Oster 3118 Manuel utilisateur

Emerson

Emerson BO61 Manuel utilisateur

Black & Decker

Black & Decker Gizmo EM200 Series Instructions d'installation

Hamilton Beach

Hamilton Beach 76606 - Pop-Top Electric Can Opener Manuel utilisateur

Kalorik

Kalorik USK DO 36918 Manuel utilisateur

Black & Decker

Black & Decker CO451 Instructions d'installation

Hamilton Beach

Hamilton Beach Walk-n-Cut 76503 Manuel utilisateur

Hamilton Beach

Hamilton Beach 76370 - Extra Tall Can Opener Manuel utilisateur

Kenwood

Kenwood CA-P70 Manuel utilisateur

Hamilton Beach

Hamilton Beach Open Ease Can Openers Manuel utilisateur

Black & Decker

Black & Decker EC100 Series Instructions d'installation

Windmere

Windmere WCO103S Instructions d'installation

Rival

Rival CN-742 Manuel utilisateur

aidapt

aidapt Spill Not Manuel de programmation

Orbegozo

Orbegozo CU 6500 Manuel utilisateur