Breville vkj784 Manuel utilisateur
HotCupHotCup™ water dispenser
boils water in secondsboils water in seconds
®
®
®
2
Important Safety Instructions
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children unless they are
older than 8 and supervised. Keep the appliance and its cord
out of the reach of children aged less than 8 years.
Never use a power base other than the one supplied with the
appliance.
Never ll the kettle above the MAX marking. If the kettle is
overlled, boiling water may be ejected.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied persons
in order to avoid a hazard.
3
Important Safety Instructions
!This appliance generates heat during use. Adequate precaution must be taken to
prevent the risk of burns, scalds, res or other damage to persons or property caused
by touching the exterior whilst in use or during cooling.
!Never use this appliance for anything other than its intended use. This appliance is for
household use only. Do not use this appliance outdoors.
!Always ensure that hands are dry before handling the plug or switching on the
appliance.
!Always use the appliance on a stable, secure, dry and level surface.
!This appliance must not be placed on or near any potentially hot surfaces (such as a
gas or electric hob).
!Do not use the appliance if it has been dropped, if there are any visible signs of
damage or if it is leaking.
!Ensure the appliance is switched off and unplugged from the supply socket after use
and before cleaning.
!Always allow the appliance to cool before cleaning or storing.
!Never immerse any part of the appliance or power cord and plug in water or any other
liquid.
!Never let the power cord hang over the edge of a worktop, touch hot surfaces or
become knotted, trapped or pinched.
!Never leave the appliance unattended when in use.
!Beware of steam coming from the spout or lid especially during relling. Never open
the lid during the boiling cycle.
!Never ll the appliance when it is positioned on the power base.
!Never use the appliance without sufcient water in it for it to operate correctly.
!Never allow the appliance to boil dry.
!Always operate the appliance with a cup or suitable container placed below the
dispensing nozzle.
4
1. Removeable drip tray
No mess, just lift it off the power base and rinse under the tap. Holds over 1 cup of
water before it needs emptying.
2. Removable stainless steel drip tray cover
3. Dispensing nozzle
4. Stop button
Press to immediately stop the boil sequence or to stop water that is being dispensed.
5. Start button
Press to start the boil sequence.
6. Dispensing control
This control allows you to select the amount of water dispensed by your HotCup™
water dispenser. Move it towards for less water or for more water.
7. Lid
8. Lid release button
Press to open the lid and ll the water tank.
9. Illuminated water reservoir
Easy ll water reservoir holds up to 2 litres.
10. Heating chamber
11. Power base
Identifying the Parts
5
t
q
w
e
r
yu i
o
a
s
6
Using Your HotCup™ Water Dispenser
Before using your HotCup™ water dispenser for the rst time
• Remove your HotCup™ water dispenser carefully from the box. Remove any
packaging and promotional material and position your HotCup™ water dispenser on
a dry, level, secure work surface away from the edge.
• Follow the instructions below on using your HotCup™ water dispenser and discard
the rst ve measures of boiling water (i.e. the rst full tank of water). This will
remove any residues that may remain from the manufacturing process.
Using your HotCup™ water dispenser
Always position your HotCup™ water dispenser in such a way that the start
button cannot be accidentally operated, especially by children. As you use your
HotCup™ water dispenser, a certain portion of the water boiled will be transferred
back to the water reservoir. This will mean the water reservoir may become hot.
Always use care when handling your HotCup™ water dispenser.
1. Press the lid release button.
2. Fill the water reservoir from your cold tap. The water level should be between the
MIN and MAX markings.
3. Close the lid and press the stop button. This will make sure that your HotCup™ water
dispenser will not immediately start a boil cycle when you place it onto the power
base.
4. Connect your HotCup™ water dispenser to a mains supply socket.
5. Place a suitable cup or container with a tea bag, coffee, sugar, etc. below the
dispensing nozzle. Never operate your HotCup™ water dispenser without a cup or
suitable container placed below the dispensing nozzle. Adjust the dispensing control
to the required setting. The control adjusts the quantity of boiling water dispensed
by your HotCup™ water dispenser. For smaller cups like teacups, set the control
towards the setting; for larger cups like coffee mugs, set the control towards the
setting. If you are not sure which setting to use, it’s best to use a lower setting until
you gain experience using your HotCup™ water dispenser.
6. Press the start button. The water tank will light up and your HotCup™ water
dispenser will start to boil.
7. The selected quantity of boiling water will be dispensed into the cup. Your HotCup™
water dispenser is now ready to use again. If, after just having boiled, the start button
doesn’t stay in the down position, simply wait a few seconds before trying it again.
Stopping your HotCup™ water dispenser
If you have started the boil procedure and then decide you want to stop your HotCup™
water dispenser for any reason, simply press the stop button. You can also stop water
that is being dispensed by pressing the stop button. The boiled water will be safely
transferred back into the water reservoir.
7
MAX
MIN
MIN
MAX
qw
e
r
t
yu
SMALL
CUP
LARGE
CUP
8
Cleaning
Always switch off and unplug your HotCup™ water dispenser and allow it to
completely cool before cleaning. Never immerse the base unit, power cord or
plug in water or any other liquid. Do not use harsh abrasives, chemicals or oven
cleaners.
Emptying your HotCup™ water dispenser
1. After your HotCup™ water dispenser has completely cooled down, unplug it from the
mains supply socket.
2. Press the lid release button.
3. Hold your HotCup™ water dispenser over a sink and pour the water out.
4. Still holding your HotCup™ water dispenser over the sink, turn it the right way up
and allow any water to drain out of the dispensing nozzle. If no water drains out of
the nozzle, it may be because the stop button has been accidentally or intentionally
pressed. Press the start button to allow water to drain from the nozzle.
5. Repeat steps 3 and 4 until all the water has been emptied from your HotCup™ water
dispenser.
If your HotCup™ water dispenser will not be used for an extended period (e.g. if you are
on holiday), we recommend that you rst empty it. Before using your HotCup™ water
dispenser again, carry out several boil cycles discarding the water each time.
Cleaning
Clean the exterior surface of your HotCup™ water dispenser with a damp cloth and then
polish it with a soft, dry cloth. Do not use steel wool pads or harsh/abrasive cleaners.
9
q
w
e
r
10
safety and efficiency
To ensure the safe and efcient operation of your HotCup™ water dispenser it is
important to descale it regularly. The harder your water the more regularly it will need
doing. Your water company should be able to tell you how hard the water is in your
area. Untreated scale deposits prevent the element conducting heat efciently therefore
wasting electricity. Scale can also cause your HotCup™ water dispenser to malfunction or
even cause premature failure.
Descaling using a proprietary descaling product
1. Fill your HotCup™ water dispenser to the MAX ll level and place an empty cup on
the drip tray. Press the start button and wait for the water to be dispensed into the
cup.
2. Add a citric acid-based proprietary descaling product to the hot water in the cup and
stir.
3. Tip the contents of the cup into your HotCup™ water dispenser and close the lid.
4. Place the empty cup on the drip tray and press the start button.
5. Wait for the water to be dispensed into the cup.
6. Discard the water from the cup.
7. Repeat steps 4, 5 and 6 until the water level is at the MIN mark. Open the lid and
empty any remaining water into the sink. Rinse your HotCup™ water dispenser by
lling it with clean water and emptying it into the sink (see Emptying your HotCup™
water dispenser on page 8).
Fill your HotCup™ water dispenser with fresh water to the MAX ll level and place an
empty cup on the drip tray.
8. Pres the start button and wait for the water to be dispensed into the cup.
9. Discard the water in the cup. Repeat steps 8 and 9 until the water level is at the MIN
mark. Open the lid and empty any remaining water into the sink.
Descaling using vinegar or citric acid
1. You can use ordinary vinegar (white or malt) or citric acid to descale your HotCup™
water dispenser. Inexpensive, ordinary vinegar can be purchased in large bottles
from any supermarket. Citric acid can be bought from pharmacies, home brewing/
winemaking suppliers or on-line retailers.
2. If you are using vinegar, make up a solution of 1 cup of vinegar to 1 cup of water. If
you are using citric acid, mix 30g of the citric acid with 500ml of water.
3. Pour the solution into the tank, close the lid and allow it to stand for 1 hour.
4. Cycle your HotCup™ water dispenser (as described in steps 4-6 above) until the
level is at the MIN mark. Open the lid and empty any remaining solution into the sink.
Rinse your HotCup™ water dispenser several times by lling it with clean water and
emptying it into the sink.
5. Fill your HotCup™ water dispenser with fresh water to the MAX ll level and place an
empty cup on the drip tray.
6. Press the start button and wait for the water to be dispensed into the cup.
7. Discard the water in the cup. Repeat steps 6 and 7 until the water level is at the MIN
mark. Open the lid and empty any remaining water into the sink.
8. Finally, rinse your HotCup™ water dispenser several times with clean water.
Autres manuels pour vkj784
1
Table des matières
Autres manuels Breville Distributeur
