Bretford EDUIWB Manuel utilisateur
EDUIWB &DIWB
Mobile Interactive White Board
1 of 25
Assembly Instructions
022-3188 - Qty 1
Bottom Frame Assembly
022-3187 - Qty 1
Upper Frame Assembly
030-1546 - Qty 1
300N Gas Spring
022-3312
Qty 1
Projector
Mount
Support
060-0952 - Qty 1
Lifting Handle Assembly
030-1545 - Qty 1
White Board
010-6120 - Qty 1
Board Retention Bracket
017-1232
Qty 1
Guide Tube
022-3331 - Qty 1
Projector Slide Assembly
060-0926 - Qty 1
Dual Arm Assembly 010-6227 - Qty 1
Laptop Tray
010-6228 - Qty 2
Outer Bracket
010-6127 - Qty 1
Cable Retention Bracket
060-0961 - Qty 2
Mounting Bar Assembly
031-9454 - Qty 1
Owners Guide
Owners
Guide
030-0538 - Qty 13
1/4-20 x 1 1/4” Carriage Bolt
030-0207 - Qty 15
1/4-20 Hex Nut
030-1026 - Qty 2
1/4-20 x 3/4” Phillips Screw
030-1234 - Qty 8
M4 x 0.7, 12mm Phillips Screw
015-0176 - Qty 4
4” Stem Caster w/Brake
030-0845 - Qty 8
M4 x 0.7 20mm Pan Hd Screw 030-1267 - Qty 4
M4 Nut
012-0692 - Qty 2
Black Vinyl Cap
012-0696 - Qty 2
1” Knurled Knob
030-0240 - Qty 2
1/4” Lockwasher
030-1569 - Qty 2
Foam Pad
030-1571 - Qty 4
1” Square Black Foam
030-1621 - Qty 2
Foam Pad
030-0272 - Qty 2
1/4-20 x 1/2” Carriage Bolt
030-0291 - Qty 4
#10-32 x 1/2” Truss Head Screw
030-0962 - Qty 2
10-32 x 1/2” Pan Hd Screw
030-1398 - Qty 4
#10 Nylon Spacer
030-1397 - Qty 12
3/16, #10 Nylon Washer 030-1657 - Qty 4
10-32 x 1.25”L Button Hd Screw
2 of 25
030-1695 - Qty 4
10-24 x 5/8” Carriage Bolt
030-0159 - Qty 4
10-24 Hex Nut
1
LOCK
LOCK
LOCK
022-3188
1x
015-0176
4x
3 of 25
2
Correct Position
Faces
shorter
side
030-0538
030-0207
030-0538
8x
030-0207
8x
022-3187
1x
4 of 25
3
030-0538
030-0207
030-1546
1x
030-0538
1x 030-0207
1x
5 of 25
4
022-3312
1x
Correct Position
6 of 25
030-0538
030-0207
030-0207
1x
030-0538
1x
7 of 25
5
022-3182
1x
030-0291
4x
030-0291
8 of 25
6
9 of 25
Follow this step ONLY if you are using an Espon Ultra Short Throw
projector. If you are not, SKIP this step.
You need to attach this bracket (#010-6662) to your projector.
Attach the bracket to the monitor as shown. You will use the following hardware:
Bolt 030-1695, Washer 030-1397 & Nut 030-0159.
The bolt and washer will go on top of the bracket and the nut goes underneath.
030-1397
030-1695 030-0159
NOTE: This bracket may not t on some older versions of the Espon projector.
If this bracket does not t on your projector, do not use it.
7
Install mounting bar assembly to your projector. NOTE:
Nylon spacers are included in the hardware pack if you need
them. Keep ALL screws loose for adjustment after projector
is mounted onto the cart.
060-0961
2x
030-0845 or 030-1234
Screw depends on the length
you need with your porjector.
030-1397
4x
030-1398
May not be necessary
with your projector
Attach projector to slide assembly.
022-3331
1x
FRONT OF PROJECTOR MUST
FACE THIS DIRECTION ON
SLIDE ASSEMBLY
030-1657
4x
030-1397
4x
10 of 25
THIS PROJECTOR IS JUST AN
EXAMPLE, YOUR PROJECTOR
MAYBE INSTALLED IN
DIFFERENT LOCATIONS IN THE
SLOTS DUE TO THE MOUNTING
HOLE LOCATIONS.
Keep ALL screws loose for adjustment after projector is mounted onto the cart.
Lens MUST
be centered
with this hole.
Ce manuel convient aux modèles suivants
1
Autres manuels Bretford Tableau blanc
