Bretford TPMUNI2 Manuel utilisateur
TPMUNI2
Basic Flush Ceiling Mount
with Quick Release
AssemblyInstructions
PARTS LIST
Qty Description
1 Arm Assembly with Ceiling Plate
1 MountingBracketHead
1 PressurePlatew/ 4 Countersunk Boreholes
1 PressurePlate
4 SwivelArms
Qty Description
4 CountersunkPhillipsScrews
4 ClampingScrews
1 Pkg. M3 Distance Bolts with Screws & Washers
1 Pkg. M4 Distance Bolts with Screws & Washers
1 Pkg. M5 Distance Bolts with Screws & Washers
1 Pkg. M6 Distance Bolts with Screws & Washers
4 Countersunk Phillips Bolts
(These bolts can be used to replace the
clampingscrews for security)
2 AllenWrenches
HARDWARE LIST
STEP 1
Removethe mounting bracket head fromthe arm assembly by unscrewingthe knob as shown
in FIGURE 1. Position the pressure plate (the one with the countersunk boreholes) onto the
mountingbracket head. Using supplied Allen wrenchsecure together with the countersunk
screws as shown in FIGURE 2.
FIGURE 1 FIGURE 2
TurnKnobtoRelease
MountingHead
WARNING: Thisarm mountis intendedto supportprojectors witha maximumweight of26lbs. If your
projectordoes nothave mountingnutsembedded inthe bottom,it cannotbeattached tothis armmount.
THIS ARM MOUNT IS INTENDED AS A CEILING MOUNT ONLY. A QUALIFIED PROFESSIONAL
SHOULD BE USED TO PROPERLY INSTALL THIS UNIT TO THE CEILING. BRETFORD DOES NOT
RECOMMEND THE USE OF POWER TOOLS AND WILL NOT BE LIABLE FOR THE IMPROPER
USE OR INSTALLATION OF ITS PRODUCTS.
STEP 2
STEP 3
Alignpressure plate assembly,swivel arms and remainingpressure plate as shown. Loosely tighten together
using the clamping screws. The number of arms you attach (either 3 or 4) will be determined by the number
of mounting nuts embedded in the bottom of your projector. Lay your projector on its top (protected by a soft
cloth or other suitable protection) to expose the bottom and the embedded mounting nuts.
ClampingScrews
PressurePlate
Assembly
SwivelArms
SwivelArms
Remaining
PressurePlate
ClampingScrews
Select correct size distance bolts for your projector and align hardware as shown. Use the
same hardware on all swivel arms. Swivel arms may be adjusted based on the size of the
projectorandthe configuration of the embedded mounting nuts. Tightlysecureclamping
screws once swivel arms are in place. NOTE: The distance bolt mounts into your projector.
Distance Bolt (Mounts to
yourProjector)
TightenClampingScrewsafter
SwivelArmsareAdjusted
STEP 4
Slide the entire assembly (including projector) into the bottom of the
arm assembly as shown. Turn knob tightly to secure in place.
TightenKnobto
Secure Assembly
in Place
Part#031-6646
Rev.01.14.04 CH
ARM SWIVEL
NEVER MAKE ANY HANDLE ADJUSTMENTS WHEN CLAMPING IS TIGHTENED
Thishandle isfor theBall and
SocketJoint Adjustment
Bretford Bretford Ltd.
11000 Seymour Avenue Technology House
Franklin Park, IL 60131 2 Etongate, 110 Windsor Road
TEL: 847.678.2545 Slough, Berkshire SL1 2JA England
800.521.9614 TEL: 01753 53 99 55
FAX: 847.678.0852 FAX: 01753 53 94 78
800.343.1779 www.bretford.com
Table des matières
Autres manuels Bretford Accessoires pour projecteur
