BraunAbility HAL2 Manuel utilisateur

HAND ACTUATED

LOCKABLES

User Manual

EN Instructions for tting and use

2HAL2, HAL3

Thank you for choosing

Hand Actuated Lockables

from BraunAbility!

The following manual is an important part of the product, providing

you with information on how to achieve maximum performance

and safe operation. Keep the manual in a safe place so that you can

refer to it when necessary.

If you have any questions about your equipment, please contact us.

Once again, thank you for placing your condence in our products!

Safe vehicle adaptation solutions

For your safety BraunAbility products are

designed and tested according to current

directives and standards.

Safety information

Fit and use

After care

Limitation of use

Fitting the Hand Actuated Lockable (HAL) to the seat leg

Adjusting HAL setting to the rail

Operating HAL

Equipment storage and maintenance

Warranty

HAL2, HAL3

Index

“Declaration of conformity” at the end of the manual.

Limitation of use

Safety information

4HAL2, HAL3

HAL2 - 2 Fixing Studs HAL3 - 3 Fixing Studs

HAL2, HAL3

Fit and use

Fitting the Hand Actuated Lockable (HAL) to the seat leg

Fit and use

1. First, remove all M10 nyloc nuts and washers from sliding stud assemblies with a 17mm wrench (Fig. 1).

2. Ensure the seat is placed facing towards the front of the vehicle. Fit sliding studs through the seat leg bracket

holes as shown above. Position both seat legs at approximately 5mm (1/4”) from the front of the handle, ensuring

alignment (Fig. 2).

3. Replace all washers and nuts and loosely fasten with a 17mm wrench (Fig. 3). Finally tighten the M10 nyloc nuts with

a torque wrench to a recommended torque of : 35-40Nm (18-22lb.ft)

Note: Two removable seat xtures are normally required for each seat. It is important

that the seat legs are set to the identical rail width where the seat is to be tted.

Both HAL need to be aligned parallel to each other in the rail.

6HAL2, HAL3

WARNING

In 3 stud version, the rear most xing MUST NOT be used in isolation.

If it is intended that the seat should face the rear, please contact BraunAbility.

M10 Nyloc Nut

17mm wrench

M10 Nyloc Nut

17mm wrench

Sliding Stud

Seat Leg

Front of Vehicle

Figure 1 Figure 2 Figure 3

HAL2, HAL3

Fit and use

Adjusting HAL setting to the rail

Fit and use

HAL lockable comes with variable adjustable setting to accommodate different rail proles and

thicknesses. Each setting relates to a different thickness depth.

Setting 1: Thinner Rail Setting 2: Standard Rail Setting 3: Thicker Rail

1. Once HAL has been tted to the seat leg, check that the lockables are on the right setting to

t the rail in your vehicle.

2. Place the seat in the rail with HAL unlocked (Fig. 4).

3. Try and lock the seat by pushing the handle forward to the locked position (Fig. 5):

A. The handle locks smoothly and the seat doesn’t rattle; HAL is set correctly.

B. The handle is difcult to push forward; looking from the front, adjust HAL by inserting a

3mm allen key and rotating half turn clockwise . Once this is done try locking HAL again.

(Repeat operation as necessary).

C. The handle locks too easily and rattles; looking from the front, adjust HAL by inserting a

3mm allen key and rotating half turn anti-clockwise. Once this is done try locking HAL again.

(Repeat operation as necessary).

IMPORTANT: Tighten by hand only. Do not use tools of any kind.

8HAL2, HAL3

Setting

Adjustment

Unlock Lock

Figure 4 Figure 5

HAL2, HAL3

Fit and use

Operating HAL

Fit and use

1. Before locating the seat into the rail, unlock HAL, by pressing the silver trigger

(Fig 6) and then pull the handle fully back (Fig 7).

2. To locate the seat in the rail, align both HAL wheels into the rail, tilt the seat

backwards slightly and wheel it along the rail to the right location. Once this is

found, lower the seat into the rail gently push it forwards or backwards until it

is located into the rail.

3. To lock the seat into the rail, push the handle forward to the upright position

(Fig 8) until you hear it click.

Anti-tamper device

The anti-tamper device, which is supplied with HAL, is an optional accessory.

1. Should you choose to use this device during transportation, just clip it on to

the silver trigger, making sure it is safely tted (Fig 9).

2. To remove the device, simply push it sideways to release the silver trigger.

Stow away securely.

Removing seat from rail

1. To release the seat from the rail,

unlock HAL, by pushing handle

forward while pressing the silver

trigger (Fig 6), then pulling the

handle fully back (Fig 7).

2. Tip the seat backwards and

remove from the rail.

10 HAL2, HAL3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels BraunAbility Fauteuil roulant

BraunAbility

BraunAbility I-RQE10MK Manuel utilisateur

BraunAbility

BraunAbility KIT 8 Manuel utilisateur

BraunAbility

BraunAbility T-ROBK Manuel utilisateur

BraunAbility

BraunAbility T-WBB Manuel utilisateur

BraunAbility

BraunAbility TOR HD QUATTRO EXPRESS Manuel utilisateur

BraunAbility

BraunAbility Turny 6-Way Manuel utilisateur

BraunAbility

BraunAbility Carony Series Manuel utilisateur

BraunAbility

BraunAbility EASISIT Manuel utilisateur

BraunAbility

BraunAbility RBC Manuel utilisateur

BraunAbility

BraunAbility 3 Point Retractable Occupant Restraint Manuel utilisateur

BraunAbility

BraunAbility Carolift 100 Manuel utilisateur

BraunAbility

BraunAbility RQ10MH Manuel utilisateur

BraunAbility

BraunAbility I-SQE16MK Manuel utilisateur

BraunAbility

BraunAbility P-SABB Manuel utilisateur

BraunAbility

BraunAbility P-LBS Manuel utilisateur

BraunAbility

BraunAbility DI-RQMH Manuel utilisateur

BraunAbility

BraunAbility PIN AND PIN HEAVY-DUTY Manuel utilisateur

BraunAbility

BraunAbility DI-RQ10PK Manuel utilisateur

BraunAbility

BraunAbility Under-Vehicle Lift NUSP34S31X48RWO Manuel utilisateur

BraunAbility

BraunAbility T-RQ10PK Manuel utilisateur

BraunAbility

BraunAbility KIT9 Manuel utilisateur

Manuels Fauteuil roulant populaires d'autres marques

Otto Bock

Otto Bock Skippi plus Manuel utilisateur

Invacare

Invacare Action 4NG series Manuel utilisateur

SORG

SORG LoopSORG 802 Manuel utilisateur

Designability

Designability WizzyBug Instructions d'installation

Vermeiren

Vermeiren RAPIDO Manuel utilisateur

Excel

Excel G5 KIDS 0285 Manuel utilisateur

M. Bartels

M. Bartels SA-3 Manuel utilisateur

nino robotics

nino robotics NIno Manuel utilisateur

Vermeiren

Vermeiren Turios Manuel utilisateur

Invacare

Invacare MK5 EX Manuel utilisateur

Invacare

Invacare Solara Spree GT Manuel

Nova

Nova TKW-12 Manuel utilisateur

BCW

BCW Advantage Manuel utilisateur

You-Q

You-Q Luca Manuel utilisateur

interco

interco Ortolight Standard Mode d’emploi

Nova

Nova 7190L Manuel utilisateur

Vermeiren

Vermeiren EZ1 Manuel utilisateur

PaceSaver

PaceSaver Scout M-300 Manuel utilisateur